GBS SureBind System Two User manual
SureBind®
System Two™
www.gbceurope.com
www.gbceurope.com
G
Instruction Manual
تﺎﻤﻴﻠﻌﺘﻟا ﻞﻴﻟد
o
AR
English 4
8
4
1
3 4 5
2
RECEIVING STRIP
SMALL HOLE
A
B
C
D
E
F
HI
G
J
4
20.9kg
597 x 457 x 274mm
220-240 VAC, 50-60Hz
22 sheets 80g/m
2
paper (3.46mm)
1 punch cycle per 15 seconds
Up to 51mm thick x 378mm wide
13-15 seconds
Subject to technical changes without prior notice.
m
m
m
• The equipment must only be operated from the type of power
source indicated in these operating instructions and the serial
label located on the rear panel of the unit.
• The socket outlet should be located near the equipment and
should be easily accessible.
• The three-pronged grounding plug is a safety feature and
outlet installed.
for an extended period of time.
• Do not operate the unit with a damaged power supply cord
or plug, after it malfunctions, or after it has been damaged in
any manner.
• Do not let the power supply cord contact hot surfaces or
sharp objects.
• Use the equipment only for its intended purpose of punching
and binding documents.
pressure bar.
• Do not place the equipment on an unstable, cart, stand or
table.The binding system may fall, causing serious bodily
the equipment, pull out the debris tray and discard pins and
YOUR SAFETY AS WELL AS THE SAFETY OF OTHERS IS
MANUAL AND ON THE PRODUCT ARE IMPORTANT
SAFETY MESSAGES. READ THESE MESSAGES
CAREFULLY.
INDICATES A POTENTIAL PERSONAL SAFETY HAZARD
THAT COULD HURT YOU OR OTHERS AS WELL AS CAUSE
PRODUCT DAMAGE OR PROPERTY DAMAGE.
OF THE PRODUCT.
Electrical shock hazard.
Do not open. No user
serviceable parts inside.
Refer servicing to qualified
service personnel.
WARNING
m
c
This safety message means that you could be seriously hurt or
killed if you open the product and expose yourself to hazardous
Hot surface.
CAUTION
m
This safety message means that some areas directly below are
hot and could burn you. Do not touch the hot areas.
5
G
Punching
1 Place the paper fully in the punch, slide the paper to the left
against the Punch Edge Guide and press the ‘Punch’ button.
2 2(20lbs bond)
paper should be punched at one time (fewer sheets if the
document and stack the punched sections on the binding
3 If you try to punch too much paper the Jam-Stopper™
feature will sense the high paper load and will retract the
punch pins and you will hear a beeping sound. Simply
separate the paper and lift and punch fewer pages at a time.
4 Remember to lay each punched segment of your documents
document on another surface can cause binding problems
Locating Pin).
Service
Unplug the unit from the electrical outlet and contact an
conditions:
- When the power supply cord or plug is damaged or frayed
- If liquid has been spilled into the equipment
- If the binding system has been exposed to rain or water
being dropped or rough handling
- If the unit does not operate normally when following these
Operating Instructions
Operating Instructions.
• Wipe exterior only with a damp cloth. Do not use any
The Debris Tray is located on the front side near the bottom
of the machine. It collects excess paper and pin segments.
The Tray should be emptied frequently.
holes.
An adjustable Guide positions the paper for punching.
Using the scale the Guide can be adjusted for 210mm,
placed for binding after it has been punched.
An adjustable Guide properly aligns the paper for binding.
The Locating Pin can be found near the lower left hand
printed.
scale that measures document thickness to help select the
contains the trigger which starts the bind cycle.
with holes).
When the equipment is turned on the indicator will light.
steady light when the bind cycle is complete.
The Tray Full indicator will light up when the Debris Tray is
full and must be emptied.
Power must be turned ‘ON’ for both punching paper and
the end of the day.
1 Adjust the Punch Edge Guide to the correct paper length.
2
correctly aligned punched paper on the strip, matching up
the holes and the strip so that the strip is not showing at the
top or bottom of the paper. Adjust the Guide if necessary by
loosening the thumb screw on top of the Guide and sliding
the Guide to the edge of the paper.
1
1
2
appropriate height for the comfortable operation.
3 Plug the power cord into the receptacle on the rear right side
of the unit and into a proper power source.
4
obstruction to protect the power receptacle and power cord.
m
6
Operation of this machine is guaranteed for 2 years from date of purchase, subject to normal use. Within the guarantee period, ACCO
.
machine to ACCO. If you return the machine, ACCO will, at its discretion, in accordance with law, either (i) repair the machine using either
Register this product online at
At the end of its useful life, your product is considered to be
WEEE. As such, it is important to note that:
WEEE is not to be disposed of as unsorted municipal waste. It
is to be collected separately such that it can be disassembled
so its components and materials can be recycled, re-used,
electricity).
the collection of WEEE, free of charge to you.
Please return your WEEE to the collection facility nearest your
sold you the product should accept your WEEE.
If you are no longer in contact with your retailer, please contact
ACCO for assistance with this matter.
disposal of waste. You can contribute to the success of these
goals by returning your WEEE to a collection facility.
Your product is marked with the WEEE symbol (wheelie bin with
an X through it). This symbol is to inform you that the WEEE is
not to be disposed of as unsorted municipal waste.
1
should be at your right with the formed studs heads up.
2 Holding the document in place with the left hand and using
the Debinder with the right hand, insert the blade between
3 With the Debinder tight against the right side of the document
and continuing to pull toward you, swing the handle of
the Debinder to the right, away from the document. This
4
next stud, swing to shear, pull to the next stud and so on. For
rapid debinding, the Debinder can be pulled toward the user in
Extreme caution should be used when using this method.
5
6 Replace the Debinder blade when it becomes dull.
54
Debinding a document which has already been bound can be
accomplished by using the Debinder Tool. A Debinder Tool is
packaged free with all systems. Additional Debinder Tools and
Binding
1
textured side down in the Strip Recess located in front of the
The Locating Pin is on the left
2
3 Now determine the correct size of the pin strip. Use the scale
beyond. Insert the strip through the document’s holes and
4
toward you and lowering it on top of the document.To
complete you will hear beeps and the Ready Indicator will
document.
If the binding cycle is not completed the Tray Full and Ready
and then on. Then rebind the document. If the binding cycle
32
7
G
properly on the Locating Pin.
Debind to take the document apart. Rebind the
document being careful to place the small hole in
comes apart easily.
Partially cut pins.
misaligned.
may need to be readjusted to ensure that the
The best way to check the machine, is to bind
is necessary.
unable to locate the cause of the problem.
The wrong strip is being used—pins
are too short for the document
thickness.
Choose a strip with longer pins. This machine
out of adjustment.
No power Incorrect electrical connection. Check the rear power plug and the wall socket to
be sure that all connections are tight.
unable to locate the cause of the problem.
punch.
Punching too much paper. Try punching less paper at one time. It is
recommended that you punch only 22 sheets
of 80g/m2(20lb bond) paper or four (4) sheets
than the recommended amount may damage
the punch.
Punched holes are torn or paper is
buckled around the holes.
Coated Paper: too many sheets Try punching less coated paper at one time.
80g/m2
housing.
If this problem occurs when you punch 22 sheets
of 80g/m2(20lb bond) paper, you should contact
Punched holes not equally spaced
from edge.
Obstruction in punch. Check punch area for jams (i.e. strip caught in
along the inside of the punch area to loosen any
trapped material.
Punched paper hangs from top or
bottom of document.
Punch misalignment.
or the right. Check punch alignment by folding
paper in half and making sure holes line up and
corners are square.
Debris Tray will not pull out. Debris Tray is too full. Push tray in and out until it pulls out freely. Empty
the Debris Tray more often.
Debinder Tool.
Incorrect use of the Debinder Tool. Make sure you use a twisting motion when
Make sure you insert the blade the
Dull Debinder Tool blade. Change the razor blade in your Debinder Tool.
8
SureBind System Two
20,9
274 × 457 × 597
60-50240-220
8022
3,46)
151
37851
15 - 13
m
m
m
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
ACCO
.
.
.
.
.
.
m
c
.
m
.
.
9
o
AR
.
:
-
-
-
-
.
-
.
.
.
.
.
.
.
51
.
1
2
3
4
m
.
.
.
.
1
2
1
A
.
.
.
B
.
C
.
8
½
)
297
210
.(
14
13
11
D
.
E
.
F
.
(
)
’‘
PIN
G
.
.
H
.
I
)
.(
J
.
K
.
.
.
.
.
(
)
’‘
ON
.
.
.
22
)
80
22
.(
4
.
.
3
Jam-Stopper
.
.
.
)
.(
1
2
3
4
10
.
.
.
.
.
.
.
.
.
.
.
.
1
2
3
4
5
6
5 4
.
.
.
ACCO
Europe
.
.
.
.
ACCO
Europe
.
.
.
.
ACCO
.ACCO
.
(2)
(1)
(
)
.
.
.
.
)
(
)
(
)
(
.
.
.
1)
25
(
1)
25
(
1)
25
.(
.(
2)
51
.(
1)
25
.
.
.
.
.
.
.
.
.
.
.
1
2
3
4
3 2
11
o
AR
215125
8022
4
3)
8022
80
ACCO Brands Europe
Oxford House
Oxford Road
Aylesbury HP21 8SZ
United Kingdom
www.accobrands.com
Ref: SureBindS2/0794
Issue: 1 (01/15)
Service
ACCO Service Division
Hereward Rise, Halesowen,
West Midlands, B62 8AN
0800 279 5102
service[email protected]
www.rexeleurope.com/service
ACCO Brands Benelux B.V.
Holtum Noordweg 11,
6121 RE Born, Holland
08000 234 931
service[email protected]
www.rexeleurope.com/service
ACCO Brands Nordic AB
80 251495
www.rexeleurope.com/service
ACCO Austria
0800 677671
www.rexeleurope.com/service
AU
ACCO France
08 05 63 02 55
www.rexeleurope.com/service
FR
ACCO Brands Nordic AB
0800 915871
www.rexeleurope.com/service
FI
ACCO Brands Nordic AB
800-7407
www.rexeleurope.com/service
IS
ACCO Brands Nordic AB
8000-4993
www.rexeleurope.com/service
LV
ACCO Brands Benelux B.V.
0800 48352
www.rexeleurope.com/service
BE
ACCO Brands Benelux B.V.
800 27649
www.rexeleurope.com/service
LU
ACCO Iberia SLP
800 8 55955
www.rexeleurope.com/service
PT
ACCO Brands Nordic AB
800 10953
www.rexeleurope.com/service
NO
Poland
00-800-1215218
www.rexeleurope.com/service
PL
ACCO Brands Nordic AB
0200899942
www.rexeleurope.com/service
SE
ACCO Hungária Kft
06-800-20886
www.rexeleurope.com/service
HU
Czech Republic
00-800-44858150
www.rexeleurope.com/service
CZ
Rexel Office Products (PTY) Ltd
011 837 7723
www.rexelsa.co.za
ZA
GBC Asia Pte Ltd
6776 0195
www.accobrandsasia.com
IN
ACCO Brands Japan K.K.
03 5351 1801
www.rexeleurope.com/service
JP
ACCO Australia
1300 366 376
www.rexeleurope.com/service
AU
Представительство компании
«АККО Дойчланд ГМБХ и КО. КГ»
8-10-8002-5585011
www.rexeleurope.com/service
RU
ACCO Iberia SLP
800 300655
www.rexeleurope.com/service
ES
ACCO Service Division
0800 939 254
www.rexeleurope.com/service
IE
ACCO Service Division
08002795103
www.rexeleurope.com/service
NI
ACCO Brands Italia S.r.l
800029359
www.rexeleurope.com/service
IT
ACCO Schweiz
0800 001790
www.rexeleurope.com/service
CH
ACCO Brands Benelux B.V.
08007238504
www.rexeleurope.com/service
DE
Table of contents
Languages:
