GCTek AlphaONE User manual

AlphaONE Instructions
Congratulations
on your new AlphaONE Filter
You have made a wise choice in choosing the AlphaONE filter. Your filter was
carefully thought out and designed to give you many years of faithful, worry free ser-
vice. Some of the care and planning of your filter is self evident in even the small things,
such as the Lifetime Warranty on the tank itself. The tanks are made of the ultimate filter
vessel material, fiberglass. This is a higher quality tank than the typical plastic tank
used on many filters.
Your clear spring check valve for the AlphaONE bead Agitator is designed so
in time (normally many, many years) when the check valve goes out you can simply
unscrew the union and replace just the valve seat itself in just a few minutes.
Your Multiport valve was carefully chosen to be the least restrictive backwash
valve on the market to give maximum flows for the least energy dollars. The internals
were carefully designed with maximum flows in mind to give further energy savings, by
allowing you to use the most energy efficient pumps on the market.
The AlphaONE Life Support System allows you to hook up a koi pond air
pump to the supplied fitting on the front of the multiport valve and supply life giving
oxygen to the filter bacteria during times of medical bypass or pump failure.
The AlphaONE Bead Agitator is a high quality air blower that injects huge
amounts of air into the vessel prior to backwash, this breaks up the bead pack which
allows for a very thorough backwash.
Rest assured that quality was the main consideration
when your AlphaONE filter was designed and assembled.
Getting to know your
AlphaONE filter
Taking a few minutes to get to know the
different components of your
AlphaONE will assure that you are using
it to it’s maximum potential.
Assembly of your
AlphaONE
AlphaONE
Tank enclosure
opening
AlphaONE
Air release valve
AlphaONE
Media Agitator
AlphaONE
Spring check valve
AlphaONE
Tank
AlphaONE
Water drain
AlphaONE
Multiport Valve
AlphaONE
Pressure gauge
AlphaONE
“ALISS”
AlphaONE
Life Support
System
1. Tighten Water
Drain being careful
to not over tighten.
2. Hand tighten
Multiport valve to
the tank. It just slips
into position and
hand tightens with
no solvent gluing.
NOTE: top fitting is
hidden in this pic-
ture.
3. Thread the
“ALISS” into place
on the front of the
Multiport valve
4. Set the MEDIA
AGITATOR in place
on top of the spring
check valve. You
may use a set screw
to attach it to the
pipe if desired. Do
not use glue to
attach.
5. Open Tank enclo-
sure with the supplied
special tool and pour
MEDIA into filter.
Replace Tank enclo-
sure cap and tighten
with special tool.
If you have any questions on your filter feel free
to give us a call and we’ll be glad to help.

AlphaONE
Life Support System
Your AlphaONE filter addresses the age old problem of
“how do I keep my beneficial bacteria from dying when I
have to do a medical bypass or I experience pump fail-
ure?”
Easy and simple. Just run a line from your koi pond
air pump and attach it to the barbed fitting on the front of
the multiport valve. Set the Multiport valve to the “RINSE”
setting prior to turning on the air pump. Turn on the air
pump and the oxygen supplied by the air pump will keep
the bacteria happy and safe for several days if necessary.
Remember, never run the water pump at the same time that
you are running your air pump. It will cause damage to the
air pump.
Winterizing the AlphaONE
1. Turn pump off and drain water from pump basket and volute.
2. Open water drain on filter. No media will come out, only wa-
ter.
3. Loosen the Multiport valve from the housing and back the
valve away from the tank to release any water in the valve.
4. Now just wait for Spring.
I
IF
F
YOU
YOU
HAVE
HAVE
QUESTIONS
QUESTIONS
ABOUT
ABOUT
YOUR
YOUR
FILTER
FILTER
SYSTEM
SYSTEM
AND
AND
NEED
NEED
HELP
HELP,
,
PLEASE
PLEASE
CONTACT
CONTACT
YOUR
YOUR
DEALER
DEALER
OR
OR
GC T
GC TEK
EK
AT
AT
405
405- -258 258- -5551 5551
F
FAX
AX 866
866- -728 728- -0678 0678
I
INFO
NFO@
@GCTEK
GCTEK.
.COM
COM
T
THANK HANK YOU YOU FOR FOR CHOOSING CHOOSING
A
ALPHA
LPHAONE ONE
— — G
GARY
ARY C
CRYER
RYER
Back washing the
AlphaONE filter
1. Turn off water pump. Move Multiport valve to “RINSE”. Turn on
AlphaONE Agitator. Run and cycle Agitator with 20 second on and 5
second off cycles for 5 or 6 cycles. Turn off Agitator.
2. While still in the “RINSE” mode, turn water pump on and run until
water starts to go out the waste line and then stop water pump.
3. Move Multiport valve to “BACKWASH” position, start water pump
and run until water is clear in sight glass. Usually 1-3 minutes. Stop
pump.
4. Move Multiport valve to the “RINSE” position, restart pump and run
until water is clear in sight glass. Stop water pump.
5. Move Multiport valve to the “FILTER” position and restart the water
pump. You’re done, it’s that simple.
Your AlphaONE filter was designed to get rid of the solids when back-
washed thus providing you with a more efficient filter and fewer back-
washings being needed.
AlphaONE
Plumbing hook up assembly
Make plumbing hook ups as shown in
the picture. Use 2” male threaded adapt-
ers to thread into the open ports of the
Muliport valve and then use unions to
secure plumbing to valve.
Waste line hook up.
Note: opening on
left side of valve. Return line back to
pond.
Water line from the
pump.
ALISS
Valve