GE Interlogix S700VT-MST User manual

Instruction Manual
S700VT-MST
FIBER-OPTIC
MINIATURE VIDEO TRANSMITTER
GE Interlogix
Fiber Options
g
x

This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used properly in strict accordance
with the instructions contained herein, may cause interference to
radio communication. It has been tested and found to comply with
the limits for Class A computing devices in accordance with the spec-
ifications found in Subpart J of Part 15 of FCC rules, which are
designed to provide reasonable protection against such interference
when the equipment is operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause
interference, in which case the user will be required to take whatev-
er means may be necessary to correct the interference at his own
expense.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
This apparatus does not exceed the Class A limits for radio noise
emission set out in the Radio Interference Regulation of Industry of
Canada.
Cet appareil numerique de la classe A respecte toutes les exigences
du Reglement sur le materiel brouilleur du Canada.
Federal Communications Commission
and Industry Canada Radio Frequency
Interference Statements
FCC PART 15
COMPLIANT

GENERAL
This manual is a guide to the installation and operation of the
S700VT-MST fiber optic video transmitter. Please read the
entire manual before installing the equipment.
NOTE: The series numbers S700VR is used the describe all
receiver models unless noted otherwise.
The S700VT-MST video transmitters system transmit one
video signal one from a camera to a monitoring station over
one multimode fiber. The S700VT-MST can be used with the
S700VR or S702VR series receivers.
A complete system consists of one transmitter and one
receivers.
Unpacking the Unit
In the event that anything is missing from the following list,
contact your authorized Fiber Options dealer or representa-
tive.
S700VT-MST Transmitter
Instruction manual
Save the original packing materials in case it becomes neces-
sary to return the unit.
Fiber Options 80 Orville Drive, Bohemia NY 11716-2533 [email protected]
US Tel: [phone] or 800-342-3748 Fax: 877-FiberFax (877-342-3732 toll free) or 631-567-8322
For international offices, see the back cover.
www.fiberoptions.com
GE Interlogix
Fiber Options
MODEL
S700VT-MMST
MINIATURE
VIDEO TRANSMITTER
g
FIGURE 1: BASIC SYSTEM DIAGRAM
one
optical fiber
Video Out
S700VT-MST S700VR
Video In
INSTRUCTION
MANUAL
FEATURES
The S700VT-MST transmitter housing is extremely small
measuring 1.5 in. (38 mm) by 1.04 (26 mm) by 24 mm
(0.94 in) . An ST optical connector is fixed to one end, while
a coaxial cable with BNC connector and a removable 2-pin
screw-terminal power connector are attached at the opposite
end.
The S700VT-MST transmitter can be used with any of the fol-
lowing receivers: S700VR-EST, S700VR-RST, S702VR-RST.
The S702VR-RST supports two transmitters.
All the receivers feature a diagnostic LEVEL/LOSSTM LED to
indicate the presence of valid fiber signal. (S702V cards have
two such LEDs).
Refer to TROUBLESHOOTING for more information. Rack-
mount receivers are designed to be mounted in a standard 19-
inch card cage (515R1 or 517R1). Electrical power input is
derived from the card cage.

INSTALLATION
The S700VT-MST transmitter is intended to be located on or
near a CCTV camera. If the camera is mounted outdoors, the
S700VT-MST must be mounted inside the camera housing.
Make sure there is sufficient space for making the various
cable, electrical, and fiber connections.
VelcroTM fastener tape is provided for mounting the S700VT-
MST to any smooth, flat surface. See Figure 2 for unit dimen-
sions.
1. Adhere the fastener tape to the transmitter by removing the
protective backing from the gummed tape. Firmly press the
tape to the unit.
2. Fasten the other piece of Velcro to the selected surface in the
same way. The S700VT-MST can now be mounted to the sur-
face by attaching the two pieces of fastener tape to each other.
CONNECTIONS
All fiber-optic links convert electrical signals into a light
source at the transmitter and convert the light back to electrical
signals for output at the receiver.
CAUTION: Make sure all peripheral equipment that will be
connected to the fiber unit is turned OFF during installation.
Video Cable Connection
Connect the video equipment, such as a camera, to the
S700VT-MST transmitter using the attached coaxial cable.
Fiber Optic Cable Connection
The standard optical connector on S700VT-MST units is the
ST type. Connect the pre-terminated fiber to the two fiber
units.
Power Connections
A removable 2-pin screw-terminal connector is provided for
the electrical connection.
1. Make sure the power supply is not connected to any power
source and attach the leads from the power supply to the
appropriate terminals as follows:
Pin 1: +13.5 VDC (DC+) or 12 - 14 VAC
Pin 2: Ground (DC-) or 12 - 14 VAC
2. Plug the power supply into a suitable outlet.
Once the S700VT-MST has been installed and the other end of
the fiber connected to a suitable receiver, power up the periph-
eral equipment.
TROUBLESHOOTING
Operation of a system including an S700VT-MST transmitter
can be monitored with the LEVEL/LOSSTM LED on the
S700VR or S702VR receivers.
When green, LEVEL/LOSS indicates the presence of sufficient
optical and video signals being received from the transmitter. If
unlit, check fiber and all connections and splices. Also check
that the transmitter is connected to an operating video source, is
on, and is connected to the receiver via the fiber.
www.fiberoptions.com
[email protected] free phone: [phone] free fax: [phone]
2
FIGURE 2: MODULE DIMENSIONS

www.fiberoptions.com
[email protected] free phone: [phone] free fax: [phone]
3
NOTE: A blank video screen can be a valid video input.
If the S700V fails to operate and the cause of the failure can-
not be determined, it may be necessary to contact Fiber
Options.
MAINTENANCE
There is no operator maintenance other than keeping the units
clean.
CONTACTING FIBER OPTIONS
If you cannot determine the cause of your problem and are in
the U.S. or Canada, call the Fiber Options Headquarters in
Bohemia, NY. If you are outside the U.S. or Canada, call the
closest international office listed on the back page of this man-
ual.
Have the following information available: exact model number
and product code of your fiber-optic links, and a listing of the
diagnostic indicators and their respective color/condition.
SHIPPING AND PACKAGING
Before shipping or transporting your Fiber Options unit, pack
it securely to prevent damage that could occur in transit. Use
care to protect all connectors, LEDs, and corners from possible
damage.
RETURNS TO FIBER OPTIONS
If any equipment must be returned to Fiber Options for repair
or replacement, you must obtain authorization from our Return
Authorization department before shipping.
If you are in the U.S. or Canada, call our NY headquarters at
631-567-8320 or 800-342-3748.
Customers in other countries should contact their regional rep-
resentative listed on the back cover of this manual. A Return
Authorizations representative will provide full instructions for
returning your product at that time.
NOTE: All authorized returns must be clearly marked with the
Return Authorization information. Please follow the instruc-
tions completely.
NOTE: Fiber Options will not accept return delivery of any
product without prior authorization.

All specifications are subject to change without notice. Information furnished by FIBER OPTIONS is
believed to be accurate and reliable. However, no responsibility or liability is assumed by FIBER
OPTIONS for its use, nor for any infringement of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or other rights of FIBER
OPTIONS.
11-M700V-A
Copyright 2001 by FIBER OPTIONS.
All rights reserved.
030919
www.fiberoptions.com
80 Orville Drive, Bohemia NY 11716-2533
[email protected]
US Tel: [phone] Fax: [phone]
800-342-3748 877-FiberFax (877-342-3732)
UK Tel: [phone] Fax: [phone]
Australia Tel: [phone] Fax: [phone]
France Tel: [phone] Fax: [phone]
Germany Tel: [phone] Fax: [phone]
Hong Kong Tel: [phone] Fax: [phone]
Latin America Tel: [phone] Fax: [phone]
. . . light years ahead™
INSTRUCTION
MANUAL