GE FUF14SVRWW User manual

New 2008 Freezer ElectronicsNew 2008 Freezer Electronics
These models will be based on the existing 14/17/21 cabinets but These models will be based on the existing 14/17/21 cabinets but
will incorporatewill incorporate
new electronic control systems mounted in the new electronic control systems mounted in the
door.door.
ModelsModels
FUF14SVRWWFUF14SVRWW
FUF14DVRWWFUF14DVRWW
FUF17SVRWWFUF17SVRWW
FUF21SVRWWFUF21SVRWW

Electronic Temperature ControlElectronic Temperature Control
When the freezer is plugged in fWhen the freezer is plugged in f
or the first time, all LED’s willor the first time, all LED’s will
turn on and the control will beep turn on and the control will beep
three times.three times.
The temperature setting of “4”The temperature setting of “4”
will be displayed.will be displayed.
This setting will This setting will
provide satisfactory food storage temperatures.provide satisfactory food storage temperatures.
Setting SelectionSetting Selection
Adjust the temperature setting by pressing “Adjust the temperature setting by pressing “
ColderColder
””
oror
““
WarmerWarmer
”.”.
Allow several hours for the temperature to stabilize Allow several hours for the temperature to stabilize
betweenbetween
adjustments.adjustments.
44

CC
oo
m p m p
OO
ff
ff
CC
oo
m p m p
OO
nn
CC
oo
m p m p
OO
ff
ff
..
CC
oo
m p m p
OO
nn
CC
oo
m p m p
OO
ff
ff
..
CC
oo
m p m p
OO
nn
1 1
--
1 1
11
4 4
--
2 2
11
3 3
--
2 2
11
33
2 2
--
4 4
11
1 1
--
5 5
11
0 0
--
5 5
11
00
3 3
--
7 7
8 8
--
8 8
7 7
--
8 8
77
4 4
--
11
0 0
5 5
--
11
2 2
3 3
--
11
1 1
44
5 5
--
11
4 4
1 1
--
11
6 6
--
1 1
--
11
5 5
00
6 6
--
11
8 8
--
3 3
--
11
9 9
--
4 4
--
11
9 9
--
44
7 7
--
22
2 2
--
7 7
--
22
2 2
--
7 7
--
22
3 3
--
88
SettingSetting
UU
22
11
F F
((
MM
oo
dd
ee
l l
00
))
UU
11
77
F F
((
MM
oo
dd
ee
l l
11
))
UU
11
44
F F
((
MM
oo
dd
ee
l l
22
))
Set Points for Temperature ControlSet Points for Temperature Control
(ºF)(ºF)
44

“0”“0”
is displayed is displayed
when the when the
freezer is freezer is
turned off. turned off.
To turTo tur
nn
the freezer off,the freezer off,
press “Warmer”press “Warmer”
three timesthree times
after theafter the
“1”“1”
temperature temperature
setting setting
is displayed. is displayed.
OFF will OFF will
turn oturn o
ffff
the compressor, the fan, the defrost system, the compressor, the fan, the defrost system,
and anyand any
alarms, but the interior lights will continue to function.alarms, but the interior lights will continue to function.
To turn the freezer on,To turn the freezer on,
presspress
“Colder”“Colder”
three timesthree times
toto
get the “1”get the “1”
setting. setting.
Continue Continue
pressing pressing
“Colder”“Colder”
until theuntil the
desired setting appears.desired setting appears.
When the freezer is unplugged, the temperatureWhen the freezer is unplugged, the temperature
setting will be retained in memory.setting will be retained in memory.
00
Turning the unit OFF and ONTurning the unit OFF and ON
OO
NN
OO
FF
FF
Control LockControl Lock
This is done by pressingThis is done by pressing
“Alarm Reset”“Alarm Reset”
forfor
three seconds.three seconds.
““
LL
””
will then will then
appear on tappear on t
he display for he display for
one second. one second.
To unlockTo unlock
the control, press “Alarm Reset”the control, press “Alarm Reset”
for 3 seconds till the “for 3 seconds till the “
UU
””
appears in the display.appears in the display.

Showroom ModeShowroom Mode
Showroom Mode allows a person to demonstrate the freezerShowroom Mode allows a person to demonstrate the freezer
features without turning on the compressor and fan or goingfeatures without turning on the compressor and fan or going
through defrothrough defro
st. st.
During ShoDuring Sho
wroom Mowroom Mo
de, all de, all
buttons buttons
operateoperate
and after the temperature setting a “and after the temperature setting a “
. ”. ”
will be displayed.will be displayed.
The interior light will operate and there will be no alarms inThe interior light will operate and there will be no alarms in
the Showroom Mode. Note: this may require two people sincethe Showroom Mode. Note: this may require two people since
the buttons MUST be depressed during power up.the buttons MUST be depressed during power up.
To enter the Showroom Mode, pressTo enter the Showroom Mode, press
“Colder”“Colder”
and “Warmer”and “Warmer”
at the same time while the freezer is plugged in. at the same time while the freezer is plugged in.
An “An “
SS
””
willwill
appear for three (3) seconds on the display appear for three (3) seconds on the display
and then theand then the
temperature temperature
setting wsetting w
ill appear. ill appear.
The ShoThe Sho
wroom Mwroom M
ode isode is
retained if the freezer is unplugged.retained if the freezer is unplugged.
ToTo
EXITEXIT
the Showroom Mode, pressthe Showroom Mode, press
“Colder”“Colder”
and “Warmer”and “Warmer”
at the same time while the freezer is plugged in.at the same time while the freezer is plugged in.
4.4.

Automatic Defrost TimingAutomatic Defrost Timing
After each 12 hours of accumulated compressor run time,After each 12 hours of accumulated compressor run time,
30 minute30 minute
s of defross of defros
t will bet will be
gin. gin.
During these During these
30 minutes30 minutes
the defrost heater will run the defrost heater will run
until the termination switchuntil the termination switch
opens. opens.
After the After the
thirty minutethirty minute
s, the s, the
compressor will compressor will
run.run.
Manual DefrostManual Defrost
To manually enter the defrost mode, turn the freezer off,To manually enter the defrost mode, turn the freezer off,
then press “then press “
WarmerWarmer
””
an an
additional additional
four four
times. times.
A A
““
dd
””
willwill
flash on the display for the flash on the display for the
thirty minutes of the defrostthirty minutes of the defrost
cycle. cycle.
To exit To exit
the manual the manual
defrost before defrost before
it is it is
complete,complete,
press “press “
WarmerWarmer
””
four four
times. times.
When When
the the
defrost defrost
mode mode
ends,ends,
the freezer will go the freezer will go
back to the previous temperature settingback to the previous temperature setting
and the compressor will run. “and the compressor will run. “
dd
””
is only displayed in thisis only displayed in this
mode, standard auto defrost displays the control setting.mode, standard auto defrost displays the control setting.
DefrostDefrost
dd

Error ModesError Modes
If the thermistor is open, the display will alternateIf the thermistor is open, the display will alternate
between “E”between “E”
and “9”and “9”
. .
If thIf th
e there ther
mistor mistor
is shoris shor
ted,ted,
the display will alternate between “E”the display will alternate between “E”
and “8”.and “8”.
If a key is If a key is
stuck for more than 30 seconds, thestuck for more than 30 seconds, the
display will alternate between “E”display will alternate between “E”
and “7”.and “7”.
If there is a thermistor error or a If there is a thermistor error or a
button is stuck forbutton is stuck for
more than 30 seconds, the compressor and fan willmore than 30 seconds, the compressor and fan will
run continuously with the standard defrost cycle.run continuously with the standard defrost cycle.
There is no capability in the control to store errorThere is no capability in the control to store error
codes.codes.

Service ModeService Mode
To enter the Service Mode,To enter the Service Mode,
lock the controllock the control
. This is done by. This is done by
pressingpressing
“Alarm Reset”“Alarm Reset”
forfor
three seconds.three seconds.
““
LL
””
will thenwill then
appear on the display for one second.appear on the display for one second.
Then press and holdThen press and hold
“Colder”“Colder”
and “Warmer”and “Warmer”
for threefor three
seconds.seconds.
When the diagnostics mode is entered, the compressor isWhen the diagnostics mode is entered, the compressor is
turned off and the digit “turned off and the digit “
8”8”
is displayed for three seconds.is displayed for three seconds.

After three seconds, the sequential information below will be displayed.After three seconds, the sequential information below will be displayed.
Blank for 0.5 seconds.Blank for 0.5 seconds.

Model Model
ID ID
for for
1 1
second, second,
““
00
””
fofo
r 2r 2
1 c1 c
ufuf
t, t,
““
11
””
ff
oo
r 1r 1
7 c7 c
uu
ftft
aa
nn
d “d “
22
””
fofo
r 1r 1
4 c4 c
ufuf
t.t.

Blank for 0.5 seconds.Blank for 0.5 seconds.

Software Version and LED test for 3 Software Version and LED test for 3
seconds.seconds.

Hi Temp LED illuminates during display of Hi Temp LED illuminates during display of
11
stst
digit of the version numberdigit of the version number
for one second.for one second.

Door Ajar LED illuminates during display of 2Door Ajar LED illuminates during display of 2
ndnd
digit of the versiondigit of the version
number for one second.number for one second.

Both LED’s illuminate during display of 3Both LED’s illuminate during display of 3
rdrd
digit of the version number fordigit of the version number for
one second.one second.

Blank for 0.5 secondsBlank for 0.5 seconds
Service Mode ContinuedService Mode Continued


Thermistor status (“Thermistor status (“
00
””
fofo
r or o
pepe
n, n,
““
CC
””
fofo
r sr s
hoho
rt rt
oror
“-”“-”
for good thermistor) forfor good thermistor) for
three seconds. Note: a bad, out of three seconds. Note: a bad, out of
spec thermistor will still showspec thermistor will still show
“-”“-”
good.good.

10 seconds for power check, using colder and warmer keys f10 seconds for power check, using colder and warmer keys f
or diagnosticor diagnostic
function of the compressor and defrost heater.function of the compressor and defrost heater.
During this 10 second time period each key activates a specific load.During this 10 second time period each key activates a specific load.
Colder Colder
button button
activates activates
the the
compressorcompressor
and lowercase “and lowercase “
cc
””
didi
spsp
laylay
eded
,,
Warmer Warmer
button button
activates activates
defrost defrost
heaterheater
and lowercase “and lowercase “
dd
””
didi
spsp
lala
yeye
d.d.
The test isThe test is
ONLYONLY
active while the button is depressed.active while the button is depressed.
10 seconds after the last key press, 10 seconds after the last key press,
the system will exit the diagnostic mode,the system will exit the diagnostic mode,
automatically assuming the default temperature setting.automatically assuming the default temperature setting.
Note:Note:
If the temperature is not satisfied by the If the temperature is not satisfied by the
control settings andcontrol settings and
the cabinetthe cabinet
temperature is below 23 degrees, the compressor has a delay start of temperature is below 23 degrees, the compressor has a delay start of
1313
minutes.minutes.
Service Mode ContinuedService Mode Continued