GE SpacemakerXL JVM1630 User manual

Installation
Instructions
Questions? Call 1-800-561-3344 or Visit our Website at: GEAppliances.ca
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Read these instructions completely and carefully.
•IMPORTANT –Save these
instructions for local inspector’s use.
•IMPORTANT –Observe all
governing codes and ordinances.
• Note to Installer –Be sure to leave these
instructions with the consumer.
BEFORE YOU BEGIN
• Note to Consumer –Keep these instructions
for future reference.
• Skilllevel – Installation of this appliance requires basic
mechanical and electrical skills.
•Proper installation is the responsibility of the installer.
•Product failure due to improper installation is not
covered under the warranty.
AbovetheCooktop
MicrowaveOven
JVM1630 and JVM1635
350A4502P740
49-40712
(06-13 ATS)
Popcorn
Convenience Cooking
Express Cook
Potato
Start
Pause
Cancel
Off
Beverage
Reheat
Set
Clock
Turntable
Surface
Light
Vent
Add
30 Sec.
Power
Level
0
8
5
2
7
4
1
9
6
3
Cook
Time
Defrost
Weight/Time
Timer
On/Off
Popcorn
Convenience Cooking
Express Cook
Potato
Start
Pause
Cancel
Off
Beverage
Reheat
Set
Clock
Turntable
Surface
Light
Vent
Add
30 Sec.
Power
Level
0
8
5
2
7
4
1
9
6
3
Cook
Time
Defrost
Weight/Time
Timer
On/Off

2
Outside Back Exhaust.................................. 20-23
Installation Overview ................................ 20
Preparing Rear Wall for
Outside Back Exhaust................................20
Attach Mounting Plate to Wall .......... 20, 21
Preparation of Top Cabinet.......................21
Adapting Blower for Outside
Back Exhaust.......................................... 21, 22
Mount the Microwave Oven ..............22, 23
BeforeYouUseYourMicrowaveOven ..................... 24
CONTENTS
General information
Important Safety Instructions........................................ 3
Electrical Requirements .................................................. 3
Tools You Will Need ......................................................... 4
Hood Exhaust ................................................................. 5,6
Damage – Shipment/Installation .................................. 7
Parts Included ................................................................... 7
Mounting Space ................................................................ 8
Step-by-step installation guide
Placement of Mounting Plate................................... 9-11
Removing the Mounting Plate............................. 9
Finding the Wall Studs.......................................... 9
Determining Mounting Plate Location ..............10
Aligning the Mounting Plate .............................. 11
Installation Types ..................................................... 12-23
Recirculating.................................................. 13-15
Attach Mounting Plate to Wall ................ 13
Preparation of Top Cabinet...................... 13
Installing the Charcoal Filter.................... 14
Mount the Microwave Oven .............. 14, 15
Installing the Charcoal Filter
without Top Access ............................ 15
Outside Top Exhaust..................................... 16-19
Attach Mounting Plate to Wall .................16
Preparation of Top Cabinet.......................17
Adjust Blower Motor ..................................17
Assemble and Install Adaptor ..................18
Mount the Microwave Oven .....................18
Adjust the Exhaust Adaptor......................19
Connecting Ductwork................................19
A
B
C
Installation Instructions

A qualified electrician must perform a ground continuity
check on the wall receptacle before beginning the
installation to ensure that the outlet box is properly
grounded. If not properly grounded, or if the wall
receptacle does not meet electrical requirements noted
(under ELECTRICAL REQUIREMENTS), a qualified electrician
should be employed to correct any deficiencies.
WARNING:
RiskofElectricShock.
Can cause injury or death:
Removehousefuseor
opencircuitbreakerbefore
beginninginstallationtoavoid
severeorfatalshockinjury.
WARNING:RiskofElectricShock.
Can cause injury or death: THIS APPLIANCE MUST BE
PROPERLY GROUNDED toavoidsevereorfatalshock.
120 V Models
The power cord of this
appliance is equipped with
a three-prong (grounding)
plug which mates with
a standard three-prong
(grounding) wall receptacle
to minimize the possibility
ofelectricshockhazard
from this appliance.
IMPORTANT SAFETY INSTRUCTIONS
3
ELECTRICAL REQUIREMENTS
Installation Instructions
Ensure proper
ground exists
before use.
CAUTION: For personal safety, the
mounting surface must be capable of supporting the
cabinet load, in addition to the added weight of this
63–85poundproduct,plusadditionalmicrowaveoven
loads of up to 50 pounds or a total weight of 113–135
pounds.
CAUTION: For personal safety, this product
cannot be installed in cabinet arrangements such as an
island or a peninsula. It must be mounted to BOTH a top
cabinetANDabackwall.
CAUTION:Toavoidtheriskofpersonal
injury(backinjuryorotherinjuriesduetoexcessive
weightofthemicrowave)orpropertydamage,youwill
needtwopeopletoinstallthismicrowave.
Where a standard two-prong wall receptacle is
encountered, it must be replaced with a properly
grounded three-prong wall receptacle, installed by a
qualified electrician.
WARNING:RiskofElectricShock.
Can cause injury or death: DO NOT, under any
circumstances,cut,deformorremoveanyoftheprongs
from the power cord. Do not use with an extension cord.
Failure to comply may cause fire.
120 V Models
This product requires a three-prong grounded outlet.
Product rating is 120 volts AC, 60 Hertz, 13.5 amps, and
1.55 kilowatts. This product must be connected to a supply
circuit of the proper voltage and frequency. Wire size must
conform to the requirements of the National Electrical
Code or the prevailing local code for this kilowatt rating.
The power supply cord and plug should be brought to a
separate 15 to 20 ampere branch circuit single grounded
outlet. The outlet box should be located in the cabinet
above the microwave oven and away from any potential
microwave ducting. The outlet box and supply circuit
should be installed by a qualified electrician and conform
to the National Electrical Code or the prevailing local code.

4
Installation Instructions
TOOLS YOU WILL NEED
#1 and #2 Phillips
screwdriver
Pencil
Ruler or tape measure and
straight edge
Carpenter square
(optional)
Tin snips (for cutting
damper, if required)
Electric drill with 3⁄16″, 7⁄16″,
1⁄2″and 5⁄8″drill bits
Hammer (optional)
Stud finder
Filler blocks or scrap
wood pieces, if needed
for top cabinet spacing
(used on recessed bottom
cabinet installations only)
Gloves Saw (saber, hole or keyhole)
Level Duct and masking
tape
Scissors (to cut
template, if necessary)
Safety goggles

5
Installation Instructions
HOOD EXHAUST
NOTE: Readthesenexttwopagesonlyifyouplantoventyourexhausttotheoutside.Ifyouplantorecirculatetheair
backintotheroom,proceedtopage6.BelowareexamplesofOutsideTopExhaustandOutsideBackExhaustductsystem
layouts.Notethepositionofthemicrowaveovenrelativetotheductsystem.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH x USED = LENGTH
Roof Cap 24 Ft. x (1) = 24 Ft.
12 Ft. Straight Duct 12 Ft. x (1) = 12 Ft.
(6″Round)
Rectangular-to-Round 5 Ft. x (1) = 5 Ft.
Transition Adaptor*
Equivalent lengths of duct pieces are based on actual tests and
reflect requirements for good venting performance with any vent hood.
Total Length = 41 Ft.
*IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will
have to be cut to fit, using the tin snips, in order to allow free movement of the damper.
The following chart describes an example of one possible
ductwork installation.
The following chart describes an example of one possible
ductwork installation.
NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared
at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH* x USED = LENGTH
Wall Cap 40 Ft. x (1) = 40 Ft.
3 Ft. Straight Duct 3 Ft. x (1) = 3 Ft.
(31⁄4″x 10″Rectangular)
90° Elbow 10 Ft. x (2) = 20 Ft.
Equivalent lengths of duct pieces are based on actual tests and
reflect requirements for good venting performance with any vent hood.
Total Length = 63 Ft.
1” = 2.5 cm; 1’ = 0.3 m

EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH x USED = LENGTH
Rectangular-to-Round 5 Ft. x ( ) = Ft.
Transition Adaptor*
Wall Cap 40 Ft. x ( ) = Ft.
90° Elbow 10 Ft. x ( ) = Ft.
45° Elbow 5 Ft. x ( ) = Ft.
90° Elbow 25 Ft. x ( ) = Ft.
45° Elbow 5 Ft. x ( ) = Ft.
Roof Cap 24 Ft. x ( ) = Ft.
Straight Duct 6″Round or 1 Ft. x ( ) = Ft.
31⁄4″x 10″Rectangular
TotalDuctwork =   Ft.
Equivalent lengths of duct pieces are based on actual tests and
reflect requirements for good venting performance with any vent
hood.
6
* IMPORTANT: If a rectangular-to-round transition
adaptor is used, the bottom corners of the damper
will have to be cut to fit, using the tin snips, in order
to allow free movement of the damper .
NOTE: If you need to install ducts, note that the total duct
length of 31⁄4″x 10″rectangular or 6″diameter round duct
shouldnotexceed140equivalentfeet.
Outside ventilation requires a HOOD EXHAUST DUCT.
Read the following carefully:
NOTE: It is important that venting be installed using
the most direct route and with as few elbows as possible.
This ensures clear venting of exhaust and helps prevent
blockages. Also,makesuredampersswingfreelyand
nothingisblockingtheducts.
Exhaust connection:
The hood exhaust has been designed to mate with
a standard 31⁄4″x 10″rectangular duct.
If a round duct is required, a rectangular-to-round
transition adaptor must be used. Do not use less than
a 6″diameter duct.
Maximum duct length:
For satisfactory air movement, the total duct length of
31⁄4″x 10″rectangular or 6″diameter round duct should
notexceed140equivalentfeet.
Elbows, transitions, wall and roof caps, etc.,
present additional resistance to airflow and are equivalent
to a section of straight duct which is longer than their actual
physical size. When calculating the total duct length, add the
equivalent lengths of all transitions and adaptors plus the
length of all straight duct sections. The chart below shows
you how to calculate total equivalent ductwork length using
the approximate feet of equivalent length of some typical
duct pieces.
Installation Instructions
1” = 2.5 cm; 1’ = 0.3 m

PART QUANTITY
Top Cabinet
Template 1
Rear Wall
Template 1
Installation
Instructions
and
Owners
Manual
1
1
Grease
Filters 2
Exhaust
Adaptor
1
Tray 1
Turntable
Ring 1
PART QUANTITY
Wood Screws
(3/16” x 2”) 2
Toggle Bolts (and
wing nuts) (1/4” x 3”) 4
Self-aligning Machine
Screw (1/4”-28 x
3-1/4”)
3
Nylon Grommet (for
metal cabinets) 2
Power Cord Strap
(plastic) 1
7
Installation Instructions
•If the unit is damaged in shipment, return
the unit to the store in which it was bought for
repair or replacement.
•If the unit is damaged by the customer, repair or
replacement is the responsibility of the customer.
•Iftheunitisdamagedbytheinstaller (if other than
the customer), repair or replacement must
be made by arrangement between customer
and installer.
DAMAGE – SHIPMENT/
INSTALLATION
PARTS INCLUDED
INSTALLATION
INSTRUCTIONS
OWNERS
MANUAL
ADDITIONAL PARTS
PARTS INCLUDED
You will find the installation hardware contained
in a packet with the unit. Check to make sure you
have all these parts.
NOTE: Some extra parts are included.
HARDWARE PACKET
≤
≤
≤
1” = 2.5 cm; 1’ = 0.3 m

8
Installation Instructions
MOUNTING SPACE NOTES:
•The space between the cabinets must be 30″wide
and free of obstructions.
•If the space between the cabinets is greater than
30″, a Filler Panel Kit may be used to fill in the gap
between the microwave oven and the cabinets.
Your Owner’s Manual contains the kit number for
your model.
•This microwave oven is for installation over ranges
up to 36″wide.
•If you are going to vent your microwave oven to the
outside, see Hood Exhaust Section for exhaust duct
preparation.
•When installing the microwave oven beneath
smooth, flat cabinets, be careful to follow the
instructions on the top cabinet template for power
cord clearance.
•Maximumcabinetdepthaboveandbesidetheunit
is 12¾″.
• For models setup in Recirc Exhaust: Do not allow
cabinetry or other objects to block the airflow of the
vent.
• The product should not be installed over any cooktop
or range with a combined BTU greater than 66,000
BTU.
Backsplash
66″or
more from
the floor
to the
top of the
microwave
oven
30″
2″
30″
min.
16-½″
Bottom edge of
cabinet needs to
be 30″or more
from the cooking
surface
12¾″
max.
1” = 2.5 cm; 1’ = 0.3 m

9
Installation Instructions
Find the studs, using one of the following methods:
A. Stud finder.
OR
B. Use a hammer to tap lightly across the mounting
surface to find a solid sound. This will indicate
a stud location.
After locating the stud(s), find the center by probing
the wall with a small nail to find the edges of the stud.
Then place a mark halfway between the edges.
The center of any adjacent studs should be 16″or 24″
from this mark.
Draw a line down the center of the studs.
IMPORTANT: The microwave must be connected to at
least one wall stud.
1
Open the box and fold back all four carton flaps fully
against the carton sides. Remove the following items
from the protective foam: installation instructions,
filters, exhaust adaptor, damper, and the small
hardware bag. Do not remove the foam protecting
the front of the microwave oven.
Then carefully roll the microwave oven and carton
over onto the top side. The microwave oven should
be resting in the foam.
REMOVING THE MICROWAVE
OVEN FROM THE CARTON/
REMOVING THE MOUNTING PLATE
FINDING THE WALL STUDS
B
A
2
PLACEMENT OF THE MOUNTING PLATE
1
Wall
Studs
Center
3
Carton
Pull the carton up and off the microwave oven.
Open the microwave oven door and remove the
plastic sheet and tape from inside the microwave
oven door. Remove the tape covering the turntable
hub.
Foam
2
3
6
Set the microwave oven upright. Remove and
properly discard plastic bags and foam.
1
The mounting plate is attached to the back of the
microwave oven. Remove the two screws holding it
to the microwave oven. The plate will be used as the
rear wall template and for mounting the microwave
oven to the wall.
4
5
1” = 2.5 cm; 1’ = 0.3 m

10
DETERMINING MOUNTING PLATE LOCATION UNDER YOUR CABINET
C
Your cabinets may have decorative trim that interferes
with the microwave oven installation. You may need to
remove the decorative trim to install the microwave oven
properly and to make it level.
THE MICROWAVE OVEN MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a front overhang, install the
mounting plate down the same distance as the front
overhang depth. This will keep the microwave oven level.
Measure the inside depth of the front overhang.
Draw a horizontal line on the back wall an equal
distance below the cabinet bottom as the inside depth
of the front overhang.
For this type of installation with front overhang,
align the mounting tabs with this horizontal line, not
touching the cabinet bottom as described in Step D.
Plate Position – flat bottom cabinet
PlatePosition–cabinetwithfrontoverhang
Mounting Plate Tabs
Touching the Cabinet
Bottom
Mounting Plate
with Tabs Below
Cabinet Bottom
the Same Distance
as the Front
Overhang Depth
At least 30″, up to 36″
Plate Position – recessed cabinet bottom
Mounting Plate
Tabs Touching the
Back Frame of the
Cabinet
30″to Cooktop
30″to Cooktop
1
2
3
Installation Instructions
1” = 2.5 cm; 1’ = 0.3 m