GE Monogram ZET1 User manual

1
30”Built-In Wall Oven
Installation
Instructions ZET1, ZET2
If you have questions, call 1.800.GE.CARES or visit our website at:
ge.com
Before You Begin
Read these instructions carefully and completely.
•IMPORTANT—Save these
instructions for local inspector’s use.
•IMPORTANT—Observe all
governing codes and ordinances.
• Note to Installer—Be sure to leave these
instructions with the consumer.
• Note to Consumer—Keep these
instructions for future reference.
• Proper installation is the responsibility
of the installer and product failure due
to improper installation is NOT covered
under warranty.
• NOTE—This appliance must be properly
grounded.
•ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
Materials Needed
Strain Relief Clamp
for 1/2”conduit Junction Box
Wire Nuts
36”of String
31-10633 12-05 JR
Parts Included
(4) 3/4″
Wood Screws
Metal Bottom
Trim Assembly
Tools Needed
1/8”Drill Bit and
Electric or Hand Drill Phillips Screwdriver
Adjustable Wrench
(2) 5/8″
Wood Screws

2
IMPORTANT SAFETY INSTRUCTIONS
Installation Instructions
For Your Safety
• Be sure your oven is installed properly by
a qualified installer or service technician.
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
• Make sure the cabinets and wall coverings
around the oven can withstand the
temperatures (up to 200°F) generated
by the oven.
This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual, properly grounded branch
circuit, protected by a circuit breaker or fuse
having amperage as noted on rating plate.
We recommend you have the electrical
wiring and hookup of your oven connected by a
qualified electrician. After installation, have the
electrician show you where your main oven
disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to wire
your oven according to governing codes could
result in a hazardous condition. If there are no
local codes, your oven must be wired and fused
to meet the requirements of the National
Electrical Code, ANSI/NFPA No. 70–Latest
Edition. You can get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new, but not
existing, construction utilize a four-conductor
connection to an electric oven. When installing
an electric oven in new construction, a mobile
home, recreational vehicle or an area where
local codes prohibit grounding through the
neutral conductor, follow the instructions in
the section on NEW CONSTRUCTION AND
FOUR-CONDUCTOR BRANCH CIRCUIT
CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system. If you connect to aluminum
wiring, properly installed connectors approved
for use with aluminum wiring must be used.
WARNING: The electrical
power to the oven supply line
must be shut off while line
connections are being made. Failure
to do so could result in serious injury
or death.
Electrical
Requirements
These Monogram built-in ovens require a
separate, properly grounded 3-wire 120/208 or
120/240 volt, 60 Hz power supply, protected by
a time delay fuse or circuit breaker.
• Double ovens are rated at 8.6 KW at 240 volt
and 7.8 KW at 208 volt.
• Single ovens are rated at 4.3 KW at 240 volt
and 3.9 KW at 208 volt.
AVERTISSEMENT :
Vous devez couper l’alimentation
électrique du four avant de le
brancher. Le défaut de se conformer
à cette procédure peut entraîner des
blessures sévères et même la mort.
Rating Plate
Location

3
Open oven door and remove
literature pack, broiler pan and grid,
oven racks, rack supports and a bag
with 9 hex nuts.
Read Installation Instructions carefully
before you begin.
Be sure to place all literature, Owner’s
Manual, Installations, etc. in a safe place
for future reference.
Remove packaging materials.
Check behind hinges and under
false bottom. Remove labels on the
outside of the door, plastic on trims
and panel, all tape around the oven,
and any shipping screws securing
the oven to the base pad.
(Continued on following page)
Installation Instructions
Pre-Installation Checklist
ALL INSTALLATION INFORMATION
ON THE FOLLOWING PAGES IS TO
BE USED FOR SINGLE AND DOUBLE
OVEN INSTALLATION!
Oven Racks
Literature
Pack
Broiler Pan
and Grid
EASY INSTALLATION OF YOUR NEW
30" WALL OVEN
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
FORYOUR SAFETY
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
ELECTRICALREQUIREMENTS
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
FORYOUR SAFETY
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
ELECTRICALREQUIREMENTS
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
FORYOUR SAFETY
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
ELECTRICALREQUIREMENTS
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
FORYOUR SAFETY
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
ELECTRICALREQUIREMENTS
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
FORYOUR SAFETY
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
ELECTRICALREQUIREMENTS
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
FORYOUR SAFETY
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
ELECTRICALREQUIREMENTS
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
FORYOUR SAFETY
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
ELECTRICALREQUIREMENTS
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
EASY INSTALLATION OF YOUR NEW
30" WALL OVEN
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
FORYOUR SAFETY
Beforeyou begin-Read these instructions completely and carefully.
IMPORTANT-Save these instructions for local inspector’s use.
IMPORTANT-OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Noteto Installer- Be sure to leave these instructions with the consumer.
OWNER-Keep these instructions for future reference.
Note-This appliance must be properly grounded (if applicable).
ELECTRICALREQUIREMENTS
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Beforeyou begin-Read these
instructionscompletely and
carefully.
IMPORTANT-Save these
instructionsfor local inspector’s use.
IMPORTANT-OBSERVE ALL
GOVERNINGCODES AND ORDIANCES.
Noteto Installer- Be sure to leave
theseinstructions with the consumer.
OWNER-Keep these instructions
forfuture reference.
Note-This appliance must be
properlygrounded (if applicable).
Rack Supports
with Hex Nuts
Temperature
Probe Graphite
Lubricant

4
Place the oven on a table or platform
even with the cutout opening.
(Platform must support 175 lbs.
[79 kg] single, 350 lbs. [159 kg]
double.)
Installation Instructions
Pre-Installation Checklistcont.
Remove the bottom trim from the top
of the oven. It will be installed at the
end of the installation process. The
trim is wrapped separately and taped
to the top of the unit.
To Remove the Door (if necessary)
Door removal is not a requirement for
installation of the product, but is an
added convenience. To remove the door:
Open the oven door as far as it will go.
Push both hinge
locks down toward
the door frame,
to the unlocked
position. This may
require a flat blade
screwdriver.
NOTE: The oven door is very heavy. Be sure
you have a firm grip before lifting the oven
door off the hinges. Use caution once the
door is removed. Do not lay the door on its
handle. This could cause dents or scratches.
Hinge
Unlocked
Position
Hinge
Slot
Hinge
Arm
DO NOT LIFT THE DOOR
BY THE HANDLE!
Place hands on both sides of
the door, and close the oven
door to the removal position,
which is most of the way.
Lift door up
and out until
the hinge arms
clear the slots.
Hinge
Unlocked
Position
Hinge
Slot
Hinge
Arm
Hinge Clears Slot
Removal Position

5
Cabinet Width 30” (76.2 cm)
Recommended
Minimum
Cutout Location
from Floor 32 1/2” (82.6 cm)
Cutout Depth 23 1/2”(59.7 cm) Min.
Cutout Width 28 1/2”(72.4 cm) Min.
28 5/8”(72.7 cm) Max.
Cutout Height 27 1/4”(69.2 cm) Min.
27 5/16”(69.2 cm) Max.
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For single
ovens, the runners and braces must
support 175 lbs. (79 kg).
Installation Instructions
Cutout for Single Built-In Oven
A1
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
CUTOUT
HEIGHT
27 1/4" MIN.
27 5/16" MAX.
CUTOUT
WIDTH
28 1/2" MIN.
28 5/8" MAX.
5"
22" TO
BOTTOM OF
JUNCTION BOX
JUNCTION BOX
LOCATION
RECOMMENDED
CUTOUT
LOCATION
32 1/2"
FROM THE
FLOOR
CABINET
WIDTH
30"
ALLOW 11/16" FOR
OVERLAP OF THE
OVEN OVER SIDE
EDGES OF CUTOUT THE OPENING
BETWEEN INSIDE
WALLS MUST
BE AT LEAST
28 1/2"WIDE
ALLOW 1" FOR
OVERLAP
ON OVEN TOP
AND BOTTOM
OF CUTOUT
21"
ALLOW A MINIMUM
OF 21" FOR CLEARANCE
TO ADJACENT CORNERS,
DRAWERS, WALLS ETC.
WHEN THE DOOR IS OPENED.
Allow 11/16”
(1.75 cm) for
overlap of oven
over side edges
of cutout
Junction Box
Location
Cabinet
Width
30” (76.2 cm)
Allow a minimum
of 21”(53.3 cm) for
clearance to adjacent
corners, drawers,
walls, etc. when
door is open
Cutout
Width
28 1/2”Min.
28 5/8”Max.
(72.4 to
72.7 cm)
22”(55.9 cm)
to Bottom of
Junction Box
5”
(12.7 cm)
Cutout
Height
27 1/4”Min.
27 5/16”Max.
(69.2 to 69.3 cm)
Recommended
minimum cutout
location from
floor 32 1/2” (82.6 cm)
Opening
Between
Inside Walls
Must Be
At Least
28 1/2”
(72.4 cm)
Wide
Allow 1”(2.5 cm)
minimum for
overlap of oven
top and 11⁄4”
(3.2 cm) overlap
of oven bottom
of cutout
21”
(53.3 cm)
This oven is not approved for
stackable or side by side installation.
NOTE: If the cabinet does
not have a front frame and
the sides are less than 3/4”
(1.9 cm) thick, shim both
sides equally to establish
the cutout width.
C
L
SUITABLE
BRACING
TO SUPPORT
RUNNERS
2" x 4" or
EQUIVALENT
RUNNERS
21 5/8"
OVER CENTERLINE
OF CABINET
Install a
solid bottom
or 2”x 4”
(5 cm x 10 cm)
or equivalent
runners level
with bottom
of cutout
Suitable
Bracing
to Support
Runners 21 5/8”
(54.9 cm)
Over Centerline
of Cabinet
The solid bottom or runners must be level
with the bottom of the cutout, or the bottom
trim may not install correctly and then
interfere with the door opening.

6
Installation Instructions
Cabinet Width 30” (76.2 cm)
Recommended
Minimum
Cutout
Location
from Floor 12” (30.5 cm)
Cutout Depth 23 1/2”(59.7 cm) Min.
Cutout Width 28 1/2”(72.4 cm) Min.
28 5/8”(72.7 cm) Max.
Cutout Height 51 13/16”(131.6 cm) Min.
51 15/16”(131.8 cm) Max.
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For double
ovens, the runners and braces must
support 350 lbs. (159 kg).
Cutout for Double Built-In Oven
NOTE: If the cabinet does
not have a front frame and the
sides are less than 3/4”(1.9 cm)
thick, shim both sides equally
to establish the cutout width.
A2
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
CUTOUT
HEIGHT
51 13/16" MIN.
51 15/16" MAX.
5"
CUTOUT
WIDTH
28 1/2" MIN.
28 5/8" MAX.
47" TO
BOTTOM OF
JUNCTION BOX
JUNCTION BOX
LOCATION
ALLOW 11/16"
FOR OVERLAP
OFTHE OVEN
OVER SIDE EDGES
OF CUTOUT
THE OPENING
BETWEEN INSIDE
WALLS MUST
BE AT LEAST
28 1/2"WIDE
ALLOW 1" FOR
OVERLAP
ON OVEN TOP
AND BOTTOM
OF CUTOUT
21"
ALLOW A MINIMUM OF 21"
FOR CLEARANCE TO
ADJACENT CORNERS,
DRAWERS, WALLS ETC.
WHEN THE DOOR
IS OPENED.
30"
CABINET
WIDTH
RECOMMENDED
CUTOUT LOCATION
12" FROM THE FLOOR
Allow 11/16”
(1.8 cm) for
overlap of oven
over side edges
of cutout
30”
(76.2 cm)
Cabinet
Width
Junction Box
Location
Allow a minimum
of 21”(53.3 cm) for
clearance to adjacent
corners, drawers,
walls, etc. when
door is open
Cutout
Width
28 1/2”
(72.4 cm) Min.
28 5/8”
(72.7 cm) Max.
Recommended
minimum cutout location
from floor 12” (30.5 cm)
47”(119.4 cm)
to Bottom of
Junction Box
Opening
Between
Inside Walls
Must Be
At Least
28 1/2”
(72.4 cm)
Wide Cutout
Height
51 13/16”
(131.6 cm) Min.
51 15/16”
(131.8 cm) Max.
5”
(12.7 cm)
21”
(52.3 cm)
Allow 1”(2.5 cm)
minimum for
overlap of oven
top and 11⁄4”
(3.2 cm) overlap
of oven bottom
of cutout
C
L
UITABLE
RACING
O SUPPORT
UNNERS
2" x 4" or
EQUIVALENT
RUNNERS
21 5/8"
OVER CENTERLINE
OF CABINET
Install a
solid bottom
or 2”x 4”
(5 cm x 10 cm)
or equivalent
runners level
with bottom
of cutout
Suitable
Bracing
to Support
Runners 21 5/8”
(54.9 cm)
Over Centerline
of Cabinet
The solid bottom or runners must be level
with the bottom of the cutout, or the bottom
trim may not install correctly and then
interfere with the door opening.

7
Installation Instructions
Cutout for Single Built-In Oven
Under Counter
A3
25"
Gas or electric cooktops
may be installed over this
oven. See cooktop installation
instructions for cutout size.
See label on top of oven for
approved cooktop models. Gas and electrical connections
for 30" gas cooktop must be
located in an adjacent accessible
location to the right. For a 36"
gas cooktop the connections
may be made to the left.
5"
240V / 208V
Junction Box
Location
36"
Typical
Countertop
Height
24"
Allow 11/16"
Overlap Top
of Oven &
Side Edges
of Cutout
28 1/2" MIN.
28 5/8" MAX.
27 1/4" MIN.
27 5/16" MAX.
Top and/or side
fillers may be
necessary if
unit is positioned
between existing
cabinets. Be sure
they are attached
securely since
they will anchor
the oven in the
cabinet.
3/4" Support
Platform
Required
MUST SUPPORT 150 LBS.
22" MIN.
Above
Support
Platform
5 9/16"
Reference dimension
for maximum support height
with typical 36" countertop
height
MUST SUPPORT 175 LBS.
(78.8 KG)
3/4” (1.9 cm)
Support Platform
Required
25”
(63.5 cm)
24”
(61 cm)
Gas and electrical connections for
30”(76.2 cm) gas cooktop must be
located in an adjacent accessible
location to the right. For 36”(91.4 cm)
gas cooktop, the connections may be
made to the left.
240V / 208V
Junction Box
Location
36” (91.4 cm)
Typical
Countertop
Height
22” (55.9 cm)
Min. Above
Support
Platform
5 9/16” (14.2 cm)
Reference dimension for
maximum support height with
typical 36”(91.4 cm) countertop
height
Top and/or side fillers
may be necessary
if unit is positioned
between existing
cabinets. Be sure
they are attached
securely, since they
will anchor the oven
in the cabinet.
Gas or electric cooktops may
be installed over this oven.
See cooktop installation
instructions for cutout size.
See label on top of oven for
approved cooktop models.
28 1/2”
(72.4 cm) Min.
28 5/8”
(72.6 cm) Max.
This oven is not approved to be
installed under a solid disk, induction
or downdraft modular cooktop. See
the label on the top of the oven for
approved models.
5”
(12.7 cm)
27 1/4”
(69.2 cm) Min.
27 5/16”
(69.2 cm) Max.
Allow 1”(2.5 cm)
overlap top of
oven and
11/16” (1.8 cm)
overlap side
edges of
cutout

8
Cabinetry
NOTE: Additional clearances between cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior 23 1/2”
(59.7 cm) depth and 9 1/4”(23.5 cm) height.
•These Monogram Ovens require 3/4”(1.9
cm) overlap on both sides. Allow 1”(2.5 cm)
Min. for top overlap and clearance to upper
doors.
•The Monogram Warming Drawers require
5/8”(1.6 cm) overlap on all sides.
•When installing a Monogram Warming
Drawer below a single or double oven, a
separate 120V, 60 Hz, properly grounded
receptacle must be installed. Refer to
installation instructions packed with the
Warming Drawer for specific installation
requirements.
Frameless Cabinets
Whenever possible, order 30”(76.2 cm)
frameless cabinet with the cutout sided to fit
the oven. If using stock cabinets, additional
finished filler pieces may be required to
cover the opening.
•A stock frameless cabinet cutout width
may be up to 28 3/4” (73 cm). If necessary,
add 1/2”(1.3 cm) cleats to the sides, flush
with the front edge of the side panels to
accept mounting screws.
NOTE: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
Cutout for Frameless Cabinets
A6
Single Oven Cutout
for Installation Over
a Monogram Warming
Drawer
A4 Double Oven Cutout
for Installation Over
a Monogram Warming
Drawer
A5
27 5/16”
(69.2 cm)
Max.
23 1/2”
(59.7 cm)
Min.
Inside
2”x 2”(5 cm x 5 cm) or
2”x 4”(5 cm x 10 cm)
Anti-Tip Block Against
Rear Wall, 9”(22.9 cm)
From Floor to Bottom
of Block
2”(5.1 cm)
Min.
Allow 5/8”
(1.5 cm)
Overlap
on All
Sides
1”(2.5 cm) Min. Above Toekick or
Adjust to Oven Installation Height
9”(22.9 cm)
Max.
28 1/2”
(72.4 cm).
51 15/16”
(131.8 cm)
Max.
23 1/2”
(59.7 cm)
Min.
Inside 2”x 2”(5 cm x
5 cm) or 2”x
4”(5 cm x 10
cm) Anti-Tip
Block Against
Rear Wall, 9”
(22.9 cm)
From Floor
to Bottom
of Block
2”(5.1 cm)
Min.
Allow 5/8”
(1.5 cm)
Overlap
on All
Sides
1”(2.5 cm) Min. Above Toekick
9”(22.9 cm)
Max.
28 1/2”
(72.4 cm)
Cabinet Depth
23 1/2”(59.7 cm)
Min. From Inside
Back to Front of
Cabinet Frame
or Side Panel
3/4”(1.9 cm) Min.
Thick Bottom Shelf
Cut Back Flush
with Front of
Side Panel
Install 1/2”
(1.3 cm)
Cleats to
Hold Oven
Mounting
Screws
30”
(76.2 cm)
28 1/2”(72.4 cm)
Min.
28 5/8”(72.7 cm)
Max.
Double
51 15/16”(131.8 cm)
Single
27 5/16”(69.2 cm)
9 1/4”
(23.5 cm).
9 1/4”
(23.5 cm).

9
NOTE: The middle rail separating the two
openings may need to be larger than the 2”
(5.1 cm) minimum shown. Always refer to the
individual installation instructions packed with
each product for specific requirements.
Combined Advantium and Wall
Oven Installation:
When installed in combination with a
Monogram single wall oven, use separate
electrical junction boxes.
•Refer to the Advantium oven installation
instructions for electrical requirements of
that product.
•These connections must be made
by a qualified electrician. All electrical
connections must meet National Electrical
Code or prevailing local codes.
NOTE: Additional clearances may be
required. Check to be sure the oven
supports above the Warming Drawer
do not obstruct the required interior 23 1/2”
(59.7 cm) depth and 9 1/4”(23.5 cm) height.
The middle rail separating the openings
may need to be larger than the 2”(5.1 cm)
minimum shown. Always refer to the
individual installation instructions packed
with each product for specific requirements.
Warming Drawer
Combined with Advantium
and Single Oven:
Install a separate 120V, 60Hz, properly
grounded receptacle. See installation
Instructions packed with each product
for specific requirements.
Note: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
Cabinetry
Single Oven Cutout
for Installation Below
a Monogram Advantium
Oven
A7 Single Oven Cutout
for Installation Between
a Monogram Advantium
Oven and a Monogram
Warming Drawer
A8
23 1/2”
(59.7 cm)
Min.
Inside
2”(5.1 cm) Min.
45 1/4”
(114.9 cm)
27 5/16”
(69.2 cm)
Max.
2”(5.1 cm) Min.
45 1/4”
(114.9 cm)
1”(2.5 cm) Min.
Above Toekick
23 1/2”
(59.7 cm)
Min.
Inside
2”(5.1 cm) Min.
9 1/4”
(23.5 cm)
27 5/16”
(69.2 cm)
Max. 28 1/2”
(72.4 cm)
Per Advantium
Requirement
28 1/2”
(72.4 cm)
Per Advantium
Requirement

10 (Continued on following page)
Installation Instructions
Electrical Connections
ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
DO NOT shorten the flexible conduit.
The conduit strain relief clamp must be
securely attached to the junction box
and the flexible conduit must be securely
attached to the clamp. If the flexible
conduit will not fit within the clamp, do not
install the oven until a clamp of the proper
size is obtained.
NOTE TO ELECTRICIAN: The 3 power
leads supplied with this appliance are
UL recognized for connection to heavier
gauge household wiring. The insulation
of these 3 leads is rated at temperatures
much higher than the temperature rating
of household wiring. The current carrying
capacity of the conductor is governed
by the wire gauge and the temperature
rating of the insulation around the wire.
Turn off the circuit breaker or remove
fuses to the oven branch circuit.
With the oven supported on a table
or platform in front of the cabinet
opening, connect the flexible conduit
to the electrical junction box as shown
below. Position the conduit in such a
manner that it will lie on top of the
oven in a natural loop when the oven
is installed. You will need to purchase
an appropriate strain relief clamp to
complete the connection of the conduit
to the junction box.
WARNING:Improper
connection of aluminum house
wiring to copper leads can
result in an electrical hazard or fire.
Use only connectors designed for
joining copper to aluminum and follow
the manufacturer’s recommended
procedure closely.
B2
B1
B
Junction Box
Location
Strain Relief Clamp
(not included)
must be used at
Junction Box
BARE
GROUND
WHITE
Place oven on a
support to assist in
connecting conduit
RED
BLACK
Conduit
48 1/2”
(123 cm)
long
GROUND
WIRE
AVERTISSEMENT :
Le raccordement inadéquat d’un
câblage résidentiel en aluminium
àdes fils de sortie en cuivre peut
entraîner un risque électrique ou
d’incendie. Utilisez uniquement des
connecteurs conçus pour raccorder
du cuivre àl’aluminium et respectez
minutieusement la procédure
recommandée par le fabricant.
5”
(12.7cm)