GE JSP46 User manual

Skill Level: High Average Low
Completion Time: 1 to 3 Hours
Proper installation is the responsibility of the installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty. See the Owners Manual for warranty
information.
CAUTION: Before you begin
Read these instructions carefully and
completely.
• IMPORTANT- Save these instructions for
local inspector’s use.
• IMPORTANT- Observe all governing codes
and ordinances.
Self Cleaning Radiant
Electric Slide-In Range
Installation
Instructions JSP46, JSP56, JS966
• NOTE TO INSTALLER- Be sure to leave
these instructions with the consumer.
• OWNER- Keep these instructions for future
reference.
• WARNING- This appliance must be
properly grounded. See “Electrical
Requirements” page 2.
Parts Included
Tools You Will Need
Pub. No. 31-10426
229C4053P412 1
“If you have questions, Call 800-GE-CARES or visit our website at:
www.GEAppliances.com”
1/4”Nut
driver
Wrench or Pliers
(for 1 7/16” nut)
Pencil
Hand or
Saber Saw
Straight Edge
or Square
Materials Needed
Lag Bolts Anchor
Sleeves 4- Wire Cord
4’long
3 -Wire Cord
4’long
(For Concrete Floors
Only)
( UL Approved 50 AMP)
OR
1
2
3
4
;
;
;
y
y
y
Drill with
1/8” Bit
Anti-Tip Bracket
Screws
Safety
Glasses
Tape Measure Pliers
Level
Rear Filler
2Screws

All rough-in and spacing dimensions must be met
for safe use of your range. Electricity to the range
can be disconnected at the outlet without moving
the range if the outlet is in the preferred location
(remove lower drawer).
To reduce the risk of burns or fire when reaching
over hot surface elements, cabinet storage space
above the cooktop should be avoided. If cabinet
storage space is to be provided above the
cooktop, the risk can be reduced by installing a
range hood that sticks out at least 5” beyond the
front of the cabinets. Cabinets installed above a
cooktop must be no deeper than 13”.
Be sure your appliance is properly installed and
grounded by a qualified technician.
WARNING: For personal safety
remove house fuse or open circuit
breaker before beginning
installation. Failure to do so could result in
serious injury or even death.
For Your Safety
2
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of
tipping, the appliance must be
secured by properly installing the
anti-tip bracket packed with the appliance.
If you pull the range out and away from the wall
for any reason, make sure the Anti-Tip bracket
is engaged when the range is pushed back
against the wall.
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual properly grounded branch circuit,
protected by a circuit breaker or fuse having
amperage as specified on the rating plate. The
rating plate is located above the storage drawer
on the oven frame.
We recommend you have the electrical wiring
and hookup of your range connected by a
qualified electrician. After installation, have the
electrician show you where your main range
disconnect is located.
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your
oven according to governing codes could result in
a hazardous condition. If there are no local
codes, your range must be wired and fused to
meet the requirements of the National Electrical
Code, ANSI/NFPA No. 70-Latest Edition. You can
get a copy by writing:
National Fire Protection Association
Battery March Park
Quincy, MA 02269
Effective January 1, 1996, the National Electrical
Code requires that new, but not existing,
construction utilize a 4 conductor connection to
an electric range. When installing an electric
range in new construction, follow the instructions
in the section on NEW CONSTRUCTION AND
FOUR CONDUCTOR BRANCH CIRCUIT
CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz electrical
system. If you connect to aluminum wiring,
properly installed connectors approved for use
with aluminum wiring must be used.
Electrical Requirements
WARNING
• All ranges can tip
• Injury to persons could result
• Install anti-tip bracket
packed with range
• See Installation Instructions

3
Installation Instructions
Pre- Installation Checklist
Inspect Installation Location
Refer to alternate construction section for
the following non standard installations.
a. Counter opening extends to the wall:
Maintop Filler (supplied with the range.)
(See Page 12 section AA for Installation
Instructions) or
Backguard (Kit JXS36XX or JXS39SS).
See page 12.
b. Counter height greater than 36 3/4”:
Lower Trim Slide-In (Kit JXS56XX).
c. One side is not enclosed by a cabinet:
Bodyside (Kit JXS76XX).
d. Island Installation:
To provide an optimum installation, the
top surface of the counter top must be
level and flat (lie on the same plane)
around the 3 sides that are adjacent to
range cooktop. Proper adjustments to
make the top flat should be made or
gaps between the countertop and range
cook top may occur. Forcing the cook
top to fit may cause excessive gaps and
could break glass and void warranty.
Inspect cutout dimensions and location
of receptacle to be sure it fits within
layout location.(See page 5.)
Do not remove the protective channel
from the sides of the glass cooktop, if
applicable, until later in installation.
Move Range Indoors In front
of Cabinet Opening
(Do not use hand trucks when moving the
unpackaged range.)
Protect the kitchen floor! Flatten and
place a piece of the shipping carton in front
of the installation location to protect the
flooring.
Carefully, tilt the range to access the range
leveling legs. Use an adjustable wrench to
screw leveling legs out so that glass
support flanges clear top of counter top.
To Procure Kits:
a. Visit GE Web Site, see page 1.
b. Call GE Answer Center, see page 1.
c. Contact Dealer
Protective Channel
Adjust

4
Installation Instructions
Pre- Installation Checklist
EASYINSTALLATION OF YOUR NEW
30"WALL OVEN
Beforeyoubegin-Readtheseinstructionscompletely and carefully.
IMPORTANT-Savethese instructionsfor localinspector's use.
IMPORTANT-OBSERVEALLGOVERNING CODES ANDORDIANCES.
NotetoInstaller-Be sure toleavethese instructions with the consumer.
OWNER-Keeptheseinstructionsfor future reference.
Note-Thisappliance must beproperly grounded (ifapplicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector'suse.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller-Besuretoleave
theseinstructionswiththe consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(ifapplicable).
FORYOURSAFETY
Beforeyoubegin-Readtheseinstructionscompletely and carefully.
IMPORTANT-Savethese instructionsfor localinspector's use.
IMPORTANT-OBSERVEALLGOVERNING CODES ANDORDIANCES.
NotetoInstaller-Be sure toleavethese instructions with the consumer.
OWNER-Keeptheseinstructionsfor future reference.
Note-Thisappliance must beproperly grounded (ifapplicable).
Beforeyoubegin-Readtheseinstructionscompletely and carefully.
IMPORTANT-Savethese instructionsfor localinspector's use.
IMPORTANT-OBSERVEALLGOVERNING CODES ANDORDIANCES.
NotetoInstaller-Be sure toleavethese instructions with the consumer.
OWNER-Keeptheseinstructionsfor future reference.
Note-Thisappliance must beproperly grounded (ifapplicable).
ELECTRICALREQUIREMENTS
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESANDORDIANCES.
NotetoInstaller- Be sure toleave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(ifapplicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector'suse.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure toleave
theseinstructionswith theconsumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliancemust be
properlygrounded(ifapplicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector'suse.
IMPORTANT-OBSERVEALL
GOVERNINGCODESANDORDIANCES.
NotetoInstaller-Be sure toleave
theseinstructionswith theconsumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliancemust be
properlygrounded(if applicable).
Beforeyoubegin-Readtheseinstructionscompletely and carefully.
IMPORTANT-Savethese instructionsfor localinspector's use.
IMPORTANT-OBSERVEALLGOVERNING CODES ANDORDIANCES.
NotetoInstaller-Be sure toleavethese instructions with the consumer.
OWNER-Keeptheseinstructionsfor future reference.
Note-Thisappliance must beproperly grounded (ifapplicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector'suse.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller-Besuretoleave
theseinstructionswiththe consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(ifapplicable).
FORYOURSAFETY
Beforeyoubegin-Readtheseinstructionscompletely and carefully.
IMPORTANT-Savethese instructionsfor localinspector's use.
IMPORTANT-OBSERVEALLGOVERNING CODES ANDORDIANCES.
NotetoInstaller-Be sure toleavethese instructions with the consumer.
OWNER-Keeptheseinstructionsfor future reference.
Note-Thisappliance must beproperly grounded (ifapplicable).
Beforeyoubegin-Readtheseinstructionscompletely and carefully.
IMPORTANT-Savethese instructionsfor localinspector's use.
IMPORTANT-OBSERVEALLGOVERNING CODES ANDORDIANCES.
NotetoInstaller-Be sure toleavethese instructions with the consumer.
OWNER-Keeptheseinstructionsfor future reference.
Note-Thisappliance must beproperly grounded (ifapplicable).
ELECTRICALREQUIREMENTS
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESANDORDIANCES.
NotetoInstaller- Be sure toleave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(ifapplicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector'suse.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure toleave
theseinstructionswith theconsumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliancemust be
properlygrounded(ifapplicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector'suse.
IMPORTANT-OBSERVEALL
GOVERNINGCODESANDORDIANCES.
NotetoInstaller-Be sure toleave
theseinstructionswith theconsumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliancemust be
properlygrounded(if applicable).
Beforeyoubegin-Readtheseinstructionscompletely and carefully.
IMPORTANT-Savethese instructionsfor localinspector's use.
IMPORTANT-OBSERVEALLGOVERNING CODES ANDORDIANCES.
NotetoInstaller-Be sure toleavethese instructions with the consumer.
OWNER-Keeptheseinstructionsfor future reference.
Note-Thisappliance must beproperly grounded (ifapplicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector'suse.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller-Besuretoleave
theseinstructionswiththe consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(ifapplicable).
FORYOURSAFETY
Beforeyoubegin-Readtheseinstructionscompletely and carefully.
IMPORTANT-Savethese instructionsfor localinspector's use.
IMPORTANT-OBSERVEALLGOVERNING CODES ANDORDIANCES.
NotetoInstaller-Be sure toleavethese instructions with the consumer.
OWNER-Keeptheseinstructionsfor future reference.
Note-Thisappliance must beproperly grounded (ifapplicable).
Beforeyoubegin-Readtheseinstructionscompletely and carefully.
IMPORTANT-Savethese instructionsfor localinspector's use.
IMPORTANT-OBSERVEALLGOVERNING CODES ANDORDIANCES.
NotetoInstaller-Be sure toleavethese instructions with the consumer.
OWNER-Keeptheseinstructionsfor future reference.
Note-Thisappliance must beproperly grounded (ifapplicable).
ELECTRICALREQUIREMENTS
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESANDORDIANCES.
NotetoInstaller- Be sure toleave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(ifapplicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector'suse.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure toleave
theseinstructionswith theconsumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliancemust be
properlygrounded(ifapplicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector'suse.
IMPORTANT-OBSERVEALL
GOVERNINGCODESANDORDIANCES.
NotetoInstaller-Be sure toleave
theseinstructionswith theconsumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliancemust be
properlygrounded(if applicable).
Beforeyoubegin-Readtheseinstructionscompletely and carefully.
IMPORTANT-Savethese instructionsfor localinspector's use.
IMPORTANT-OBSERVEALLGOVERNING CODES ANDORDIANCES.
NotetoInstaller-Be sure toleavethese instructions with the consumer.
OWNER-Keeptheseinstructionsfor future reference.
Note-Thisappliance must beproperly grounded (ifapplicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector'suse.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller-Besuretoleave
theseinstructionswiththe consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(ifapplicable).
FORYOURSAFETY
Beforeyoubegin-Readtheseinstructionscompletely and carefully.
IMPORTANT-Savethese instructionsfor localinspector's use.
IMPORTANT-OBSERVEALLGOVERNING CODES ANDORDIANCES.
NotetoInstaller-Be sure toleavethese instructions with the consumer.
OWNER-Keeptheseinstructionsfor future reference.
Note-Thisappliance must beproperly grounded (ifapplicable).
Beforeyoubegin-Readtheseinstructionscompletely and carefully.
IMPORTANT-Savethese instructionsfor localinspector's use.
IMPORTANT-OBSERVEALLGOVERNING CODES ANDORDIANCES.
NotetoInstaller-Be sure toleavethese instructions with the consumer.
OWNER-Keeptheseinstructionsfor future reference.
Note-Thisappliance must beproperly grounded (ifapplicable).
ELECTRICALREQUIREMENTS
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESANDORDIANCES.
NotetoInstaller- Be sure toleave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(ifapplicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector'suse.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure toleave
theseinstructionswith theconsumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliancemust be
properlygrounded(ifapplicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector'suse.
IMPORTANT-OBSERVEALL
GOVERNINGCODESANDORDIANCES.
NotetoInstaller-Be sure toleave
theseinstructionswith theconsumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliancemust be
properlygrounded(if applicable).
Beforeyoubegin-Read these instructions completely and carefully.
IMPORTANT-Savethese instructions for local inspector's use.
IMPORTANT-OBSERVEALL GOVERNING CODES AND ORDIANCES.
NotetoInstaller- Be sure to leave these instructions with the consumer.
OWNER-Keepthese instructions for future reference.
Note-Thisappliance must be properly grounded (if applicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
FORYOURSAFETY
Beforeyoubegin-Read these instructions completely and carefully.
IMPORTANT-Savethese instructions for local inspector's use.
IMPORTANT-OBSERVEALL GOVERNING CODES AND ORDIANCES.
NotetoInstaller- Be sure to leave these instructions with the consumer.
OWNER-Keepthese instructions for future reference.
Note-Thisappliance must be properly grounded (if applicable).
Beforeyoubegin-Read these instructions completely and carefully.
IMPORTANT-Savethese instructions for local inspector's use.
IMPORTANT-OBSERVEALL GOVERNING CODES AND ORDIANCES.
NotetoInstaller- Be sure to leave these instructions with the consumer.
OWNER-Keepthese instructions for future reference.
Note-Thisappliance must be properly grounded (if applicable).
ELECTRICALREQUIREMENTS
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
Beforeyoubegin-Read these instructions completely and carefully.
IMPORTANT-Savethese instructions for local inspector's use.
IMPORTANT-OBSERVEALL GOVERNING CODES AND ORDIANCES.
NotetoInstaller- Be sure to leave these instructions with the consumer.
OWNER-Keepthese instructions for future reference.
Note-Thisappliance must be properly grounded (if applicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
FORYOURSAFETY
Beforeyoubegin-Read these instructions completely and carefully.
IMPORTANT-Savethese instructions for local inspector's use.
IMPORTANT-OBSERVEALL GOVERNING CODES AND ORDIANCES.
NotetoInstaller- Be sure to leave these instructions with the consumer.
OWNER-Keepthese instructions for future reference.
Note-Thisappliance must be properly grounded (if applicable).
Beforeyoubegin-Read these instructions completely and carefully.
IMPORTANT-Savethese instructions for local inspector's use.
IMPORTANT-OBSERVEALL GOVERNING CODES AND ORDIANCES.
NotetoInstaller- Be sure to leave these instructions with the consumer.
OWNER-Keepthese instructions for future reference.
Note-Thisappliance must be properly grounded (if applicable).
ELECTRICALREQUIREMENTS
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
Beforeyoubegin-Read these instructions completely and carefully.
IMPORTANT-Savethese instructions for local inspector's use.
IMPORTANT-OBSERVEALL GOVERNING CODES AND ORDIANCES.
NotetoInstaller- Be sure to leave these instructions with the consumer.
OWNER-Keepthese instructions for future reference.
Note-Thisappliance must be properly grounded (if applicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
FORYOURSAFETY
Beforeyoubegin-Read these instructions completely and carefully.
IMPORTANT-Savethese instructions for local inspector's use.
IMPORTANT-OBSERVEALL GOVERNING CODES AND ORDIANCES.
NotetoInstaller- Be sure to leave these instructions with the consumer.
OWNER-Keepthese instructions for future reference.
Note-Thisappliance must be properly grounded (if applicable).
Beforeyoubegin-Read these instructions completely and carefully.
IMPORTANT-Savethese instructions for local inspector's use.
IMPORTANT-OBSERVEALL GOVERNING CODES AND ORDIANCES.
NotetoInstaller- Be sure to leave these instructions with the consumer.
OWNER-Keepthese instructions for future reference.
Note-Thisappliance must be properly grounded (if applicable).
ELECTRICALREQUIREMENTS
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
Beforeyoubegin-Read these instructions completely and carefully.
IMPORTANT-Savethese instructions for local inspector's use.
IMPORTANT-OBSERVEALL GOVERNING CODES AND ORDIANCES.
NotetoInstaller- Be sure to leave these instructions with the consumer.
OWNER-Keepthese instructions for future reference.
Note-Thisappliance must be properly grounded (if applicable).
Beforeyoubegin-Read these instructions completely and carefully.
IMPORTANT-Savethese instructions for local inspector's use.
IMPORTANT-OBSERVEALL GOVERNING CODES AND ORDIANCES.
NotetoInstaller- Be sure to leave these instructions with the consumer.
OWNER-Keepthese instructions for future reference.
Note-Thisappliance must be properly grounded (if applicable).
EASYINSTALLATION OF YOUR NEW
30"WALL OVEN
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
FORYOURSAFETY
Beforeyoubegin-Read these instructions completely and carefully.
IMPORTANT-Savethese instructions for local inspector's use.
IMPORTANT-OBSERVEALL GOVERNING CODES AND ORDIANCES.
NotetoInstaller- Be sure to leave these instructions with the consumer.
OWNER-Keepthese instructions for future reference.
Note-Thisappliance must be properly grounded (if applicable).
ELECTRICALREQUIREMENTS
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
Beforeyoubegin-Read these
instructionscompletelyand
carefully.
IMPORTANT-Savethese
instructionsforlocal inspector's use.
IMPORTANT-OBSERVEALL
GOVERNINGCODESAND ORDIANCES.
NotetoInstaller- Be sure to leave
theseinstructionswith the consumer.
OWNER-Keepthese instructions
forfuturereference.
Note-Thisappliance must be
properlygrounded(if applicable).
Broiler Pan
and Grid
Oven Racks
Literature
Pack
Open oven door and remove literature
pack, broiler pan and grid, and oven
racks.
Open door to the Broil Stop position.
Grasp door on both sides, and lift up
and off hinges.
Stop Guide
Storage Drawer Removal
Pull the drawer out until it stops.
Lift the front of the drawer until the
stops clear the guides.
STOP STOP
RAIL
Pull foward and remove the Drawer.
GUIDE
Remove packaging materials on door,
plastic on trims and panel, and all tape
around the range.

5
Installation Instructions
Pre- Installation Cutout and Required
Clearances
A
If cabinets are placed less than 30” above the
range, see alternate construction page 12.
NOTE: Product meets UL requirements for 0”
clearance to back and side walls.
Wall coverings, counters and cabinets around
range must withstand heat (up to 200°F)
generated by the range.
31-1/4"
2-7/8"
To Front
Surface Of
Countertop
Door Clearance
From Front
Surface of
Countertop
20-5/8"
5-1/2" 19" 5-1/2"
29-15/16"MIN
30-1/16" MAX
23-3/16"
7"
Acceptable
Electrical
Outlet Area
30" Min.
30" Min.
from
cooking
surface to bottom
of overhead
cabinets
Shave Raised Edge
To Clear 31-1/8"
Wide Control Panel
6" Min.
FromWalls
9/16"
A
13"
Max.
depth
24"Min.
For Optimum
InstallationThese
Surfaces Must
Be Flat & Level
Max. depth of
cord, plug and
recpt. box
4" to prevent
interference
with drawer
Follow instructions
packaged with alternate
appliance.
Countertop
Depth 25"
35-1/2" to 36-1/2"
from floor to
countertop
15" Min. vertical
distance from the
bottom of the adjacent
overhead cabinets

6
Standard Installation
B
Installation Instructions
If the construction of your cabinet cannot
provide a 1/4” flat area back of the countertop
opening, consider changing the counter top to
accomodate this dimension. See alternate
constructions section. If the area is not flat,
excess tension may be applied to the glass
causing breakage and voiding the warranty.
B1
Remove countertop raised edge. If
incorporated (See illustration on page 5).
Center the 30” wide opening over the
adjacent cabinets and mark with a
straight edge.
B2 Using a straight edge mark the back line
at 23-3/16” from the front edge of the
counter.
B3 Be careful not to damage the adjacent
cabinets while cutting the countertop.
Use a hand or saber saw to make
straight smooth cuts.
B4
1/4"
R
FLAT AREA
36"
23-3/16" 25"Typically
Standard Installation
29 -15/16 to 30 -1/16"
Smooth Cut
Wall
9/16" Min.
Flat
1/4" Min.
Flat
9/16" Min.
Flat

7
Installation Instructions
Electrical Connections
C
C1 Remove wire cover at
lower rear of range.
WIRE COVER
C2 When using a power cord, remove the
knockout in the connection plate with
pliers as required by the size of the
strain relief or clamp supplied with cord.
Knockout
Terminal
Housing
C3 Insert power cord through hole in the
terminal housing, engage and tighten
strain relief clamp, leaving enough wire
length to attach terminals to terminal
block.
C3a
Connection
Plate
Strain
Relief
Clamp
3 wire
cord kit
FOLLOW INSTRUCTIONS BELOW IF
YOUR CORD IS 3 WIRE.
The power cord center wire must
be connected to middle terminal
on block. Attach remaining wires
securely. Do not remove ground
strap
C5 Re-install the wire cover making sure
the wires do not become pinched
between wire cover and housing.
50 Amp 4 Wire
C4a Follow instructions
below if your cord is 4
wire.
C4b Remove the screws on
the terminal block. Do
not remove terminal
block.
Remove
3 screws
REMOVE & DISCARD
GROUND STRAP
GROUND
WIRE
REUSE
GROUND WASHER
& GROUND SCREW
C4c Remove the
green ground
screw. Then
remove the
ground strap and
discard it.
Terminal Block
C4d Attach the green or bare wire below the
terminal block with the green ground
screw and washer that were removed
earlier.
C4e Connect the red and black wires to the
outside terminals. The white wire must be
connected to the center terminal.
OR
Remove
3 screws
Black White
Red
3-Screws
Grounded
Neutral
Terminal
Center
Wire
(white)
Ground
Wire
Strain
Relief
Clamp
Ground Screw
& Washer
Black White Red
50 Amp 3Wire
NEW CONSTRUCTION AND FOUR
CONDUCTOR BRANCH CIRCUIT
Strain
Relief
Clamp

8
Installation Instructions
Installing the Anti-Tip Bracket
D
a. For concrete installation you will need two
1/4"x 1-1/2" lag screws, and two sleeve
anchors.
b. Locate the center of the four holes identified
in Fig. 1 as Floor-Concrete and Wall. Drill
the recommended size holes in each.
c. Install the sleeve anchors into the predrilled
concrete holes and install the lag and wall
screws through the Anti-Tip bracket. Make
sure the screws are securely tightened.
a. Locate the centers of the four holes identified
in Fig. 1 as Floor-Wood and Wall.
b. Drill a 1/8" pilot hole through the pre-marked
areas. Note the angle of the wall screw in
Fig. 2.
c. Mount the Anti-Tip bracket with the four
screws provided.
Locating The Bracket
a. Decide whether the bracket will be
installed on the right or left side of range
opening.
b. Place the bracket as shown in Fig. 1.
Fig. 1
Installing The Bracket in Wood
or Concrete
D1
INSTALLATION–WOOD CONSTRUCTION
I NSTALLATION–CONCRETE CONSTRUCTION
D2
Fig. 2
ATTACHMENT TO WALL
WALL
PLATE
BRACKET
SCREW MUST
ENTERWOOD
OR METAL
TO FRONT EDGE
OF
COUNTERTOP 25"
WALL
FLOOR-WOOD
REAR
LEVELING
LEG
ADJACENT CABINET
BRACKET
SIDE
FLOOR-CONCRETE
30"
Equal Space
Each Side
LargerThan 30" Opening

Position the range in front of the
cabinet opening.
SLIDE RANGE INTO OPENING
9
Installation Instructions
Installing the Range
E
E1
E8
Make sure that the glass which
overhangs the countertop clears the
countertop. Raise the unit by lowering
the leveling legs if necessary.
E2
Push while lifting the range into the
opening until the range is within 2” of
engaging the anti-tip bracket
E3
E4 Remove the protective trim from the
side of glass. (If provided)
E5 Using the adjustable pliers or wrench
carefully screw in the back leveling leg
until the glass overhang comes to rest
on the counter top.
E6 Then carefully screw in the front two
leveling legs (similar to E5) until the
glass overhang touches the
countertop.
Plug range cord into receptacle. Locate
the cord in the back of the range in a
manner that will not touch or be moved
by the drawer.
Continued on following page
Countertop
Make sure the edge
of the countertop fits flush
against the end of the
Front Control Panel
E7 Carefully push the range into the
opening until the counter top fully
engages the control panel. The back
glass overhang should cover the cutout
opening.
STORAGE DRAWER
POSITION RANGE CORD
SOTHATTHERE IS NO
INTERFERENCEWITH
STORAGE DRAWER
AdjustableWrench
or Pliers

10
Installation Instructions
Installing the Range (Cont.)
E
E9 When installation is
complete and the
range is in place,
inspect to be sure
the rear leveling leg
is fully inserted into
the slot of the Anti-
Tip Bracket.
Final Check of the Anti-Tip Bracket
E10 Make sure the hinge is in the broil
stop position.
Grasp the door on both sides.
Lift the door over the hinges lining up
the hinges with the hinge slots on the
bottom of the door.
Slide the door down onto the hinges
as far as it will go and close the door.
E11
E12
E13
CAUTION: The oven door is heavy.
You may need help lifting the door
high enough to slide it down onto
the hinges. Do not lift the door by
the handle.
Replacing the Oven Door
Place the
drawer rail on
the guides.
Replacing the Storage Drawer
E14
Push the
drawer in until
it stops.
E15
Lift the front of the drawer and push in
until the stops clear the guides.
IF DRAWER WON'T CLOSE
Remove and replace, making sure the power
cord is not obstructing the drawer and/or the
rail is in the guide.
IF DRAWER IS CROOKED
Lower the front of the drawer and
push in until it closes.
Remove and replace making sure the rail is in
the guide.
SPECIAL INSTRUCTIONS IF YOU
HAVE PROBLEMS WHILE
REPLACING THE STORAGE
DRAWER
E17
Stop
E16

11
Final Check List
Installation Instructions
Operation Check List
Check to make sure the circuit breaker is closed (Reset) or the circuit fuses are replaced.
Be sure power is in service to the building.
Check to be sure that all packing materials and tape on metal panel (if applicable) under
control knobs and drawer have been removed.
Check to make sure the Clock display is energized. If a series of horizontal red lines appear in
the display, disconnect power immediately. Recheck the range wiring connections. If change is
made to connections, retest again. If no change is required, have building wiring checked for
proper connections and voltage. It is recommended that the clock be changed if the red lines
appear.
Push down and turn any one of the four surface knobs to “MED” setting to observe that the
element glows within 15 seconds. Turn the knob off when glow is detected. If the glow is not
detected within the time limit, recheck the range wiring connections. If change is required,
retest again. If no change is required, have building wiring checked for proper connections and
voltage.

12
Alternate Construction
Installation Instruction Preparation
If counter opening extends to the wall, it will require
Maintop Filler Kit (supplied with the range) or
Backguard Kit (JXS36XX or JXS39SS) to close the
gap.
Note: If the counter top is greater than 25” it will show a
gap between the backguard and wall or between filler
kit and the wall.
If the countertop is less than 25” a gap will occur
between the countertop front and the control panel
ends (See section E7).
Optional Maintop Filler or
Backguard Kit
AA AB
Countertops higher than 36 1/2”
If countertop height
is between 36 1/2”
and 38” a lower trim
kit (JXS56XX) is
recommended.
Refer to Kit
instructions for
installation details.
If you are using the optional backguard kit,
Refer to the Backguard Kit instructions for Installation
details.
If you use the filler kit, place the metal filler piece
supplied with the range to the back of the range as
shown in the figure below. Start the 2 screws into the
upper holes at the outside rear of the range above the
louvers, through the slots in the trim, holding the filler
piece centered on the maintop frame and pushing
upward to close the gap between the bottom of the
glass and the filler trim.
When the trim is set in the proper position tighten the 2
mounting screws. The top of the trim should be located
below the top surface of the glass to prevent pots, pans
and skillets from damaging the painted parts.
Refer to the Standard Installation of the Range
beginning on page 3.
AC For Non-Built-In Installation
(End of Cabinet Location)
When installing the range at the end of a cabinet
section which will expose the unfinished side of the
range, use Body Side Kit (JXS76XX), Refer to kit
instructions for installation details.
AD Island Installation
Attach the anti-tip bracket per instructions in section D
making sure that the rear of the bracket is 25” from the
front of the countertop.
Beware that the screws provided are long and may
penetrate through the back of the island cabinets. In
this event, use shorter screws (not provided) or the
screws provided should be used in the floor, (See
Section D for Wood/Concrete Floor Installation). Do not
use Backguard Kit JXS36XX or JXS39SS.
AE
For Cabinet Openings
Approximately 30-3/8”
If range is installed in cabinet opening approximately
30-3/8” the Vertical Side Trim Kit (JXS86XX) should be
used to cover gaps between range sides and cabinet.
Refer to the kit instructions for installation details.
AF Cabinets over the Range less
than 30”
If a 30” clearance between cooking surface and
overhead combustible material or metal cabinets
cannot be maintained, protect the underside of the
cabinets above the cooktop with not less than 1/4”
insulating millboard covered with sheet metal not less
than 0.0122” thick.
Pub. No. 31-10426
229C4053P412
25" Must Be
Level
30"
Smooth Cut
Must Be Level
31-1/8"
Must Be
Flat Must Be
Flat
Wall
Maintop Filler
Range
Cooktop
( 2) #8 Screws
30"
1"
9/16"
Each Side
23-3/16"
36-3/4" to 38"
to Floor
Flat & Level
With Back &
Opposite Side
1/4"