For answers to your Monogram,® GE Profile™or
GE®appliance questions, visit our website at
ge.com or call GE Answer Center®service,
800.626.2000.
Specification Created 1/07 230144
You must use the rear filler strip kit shipped with
the range or the optional accessory backguard
when installing these ranges
Note: Cabinets installed adjacent to slide-in
ranges must have an adhesion spec of at least
194° temperature rating.
Optional Kits for Slide-In Gas Ranges:
(Available at additional cost)
Lower/Side Trim Kits
JXS56BB - Lower Trim Kit (Black)
Accessory Backguards
JXS32SS - Brushed-Chrome Accessory Backguard
JXS37BB - Black Glass Accessory Backguard
Installation Information: Before installing, consult
installation instructions packed with product for
current dimensional data.
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
Dimensions and Installation Information (in inches)
PGS908SEM
GE Profile™ 30" Slide-In Gas Range
28-1/4*
36
Maintain
at least 6"
from nearest
combustible
surface.
Acceptable
Electrical
Outlet Area
30" Slide-In Range
Dimensions (in inches)
45-1/8
2-1/4
5
6
4-1/2
30
30" Min.
15" Min. 6
30" Slide-in Elec. Range
Aug. 8, 2003 -km
23-3/16
30
30
If you are NOT using the
Filler strip or Backguard:
If you are using the
Filler strip or Backguard:
25
*Wall to front of
closed door handle
on model JSP34.
28" on models
JSP26/JSS26/16.
Note: Range may be placed with 0" clearance (flush) at the back wall and side walls
below countertop if the range side trims above the countertop extend beyond the cabinet
fronts at least 1/4". (Self-clean models only.) Maintain at least 6" distance from nearest
combustible surface.
30
31-1/2
28-1/4*
36
Maintain
at least 6"
from nearest
combustible
surface.
Acceptable
Electrical
Outlet Area
30" Slide-In Range
Dimensions (in inches)
45-1/8
2-1/4
5
6
4-1/2
30
30" Min.
15" Min. 6
30" Slide-in Elec. Range
Aug. 8, 2003 -km
23-3/16
30
30
If you are NOT using the
Filler strip or Backguard:
If you are using the
Filler strip or Backguard:
25
*Wall to front of
closed door handle
on model JSP34.
28" on models
JSP26/JSS26/16.
Note: Range may be placed with 0" clearance (flush) at the back wall and side walls
below countertop if the range side trims above the countertop extend beyond the cabinet
fronts at least 1/4". (Self-clean models only.) Maintain at least 6" distance from nearest
combustible surface.
30
31-1/2
2-7/8"
To Front
Surface Of
Countertop
20-5/8"
Door Clearance
From Front
Surface of
Countertop
31-1/4
30
A*
Accessory
Backguard
36
2"
(Grates)
24
Acceptable
Gas Line &
Electrical
Outlet Area
Max. depth of
cord, plug,
receptacle box
& gas hookup
3-1/2" to prevent
interference
with drawer
30" Min.
Shave Raised Edge To Clear
31-1/8 Wide Control Panel
30" Min. to
unprotected
cabinet from
countertop
23-3/16
18" Min.
13" Max.
3
29-15/16" Min.
30-1/16" Max.
25
9/16
7
12
15
*A – JXS37 is 5-1/4" and JXS32 is 4"
27-1/2**
44-3/4
(excluding handle)
**Total depth from wall to
front of closed oven door
including handle is 30-1/2.
B is 9-1/2" from walls on either side for P2S975, PGS975
and PGS908 and 6” for PGS968
B
35-7/8"–38"
from floor to
countertop
Counter Cutout Dimensions (in inches)
2-7/8"
To Front
Surface Of
Countertop
20-5/8"
Door Clearance
From Front
Surface of
Countertop
31-1/4
30
A*
Accessory
Backguard
36
2"
(Grates)
24
Acceptable
Gas Line &
Electrical
Outlet Area
Max. depth of
cord, plug,
receptacle box
& gas hookup
3-1/2" to prevent
interference
with drawer
30" Min.
Shave Raised Edge To Clear
31-1/8 Wide Control Panel
30" Min. to
unprotected
cabinet from
countertop
23-3/16
18" Min.
13" Max.
3
29-15/16" Min.
30-1/16" Max.
25
9/16
7
12
15
*A – JXS37 is 5-1/4" and JXS32 is 4"
27-1/2**
44-3/4
(excluding handle)
**Total depth from wall to
front of closed oven door
including handle is 30-1/2.
B is 9-1/2" from walls on either side for P2S975, PGS975
and PGS908 and 6” for PGS968
B
35-7/8"–38"
from floor to
countertop
