GE 19 M User manual

Appliance Registration 2
Automatic Icemaker 5-7
Behind the Refrigerator 11
Care and Cleaning 11, 12
CFC-Free Refrigerant 2
Consumer Services 20
Food Storage Suggestions 8
Ice Service 7
Installation Requirements 14
Adapter Plug 14
Electrical Requirements 14
Extension Cord 14
Grounding 14
Light Bulb Replacement 12
Model and Serial Numbers 2
Problem Solver 17-19
Preparation 13
Clearances 13
Location 13
Rollers and Leveling Legs 13
Water Supply to Icemaker 13
Vacation & Moving Tips 13
Safety Instruction 3
Shelves 10
Storage Drawers 9
Drawer & Cover Removal 12
Temperature Controls 4
Under Refrigerator 11
Warranty U.S. Back Cover
Warranty Canadian 21
Water Filter Accessory 7
Water Line Installation 15, 16
Version française 23
Versión en español 45
English Version
Use and Care of
Side by Side
19, 20, 22, 24
and 27 Models
Your
Refrigerator
How to get
the best from
In the United States call the GE Answer Center®800.626.2000
In Canada consult your local telephone directory for the Camco Service Center

HELP US HELP YOU…
Write down the model
and serial numbers.
You’ll see them on a label on the wall beside
the top drawer or at the bottom, just inside the
fresh food compartment door.
These numbers are also on the Consumer
Product Ownership Registration Card that
came with your refrigerator.
Before sending in this card, please write these
numbers here:
Model Number
Serial Number
Use these numbers in any correspondence or
service calls concerning your refrigerator.
Read this guide carefully.
It is intended to help you operate and
maintain your new refrigerator properly.
Keep it handy for answers to your questions.
If you don’t understand something or need
more help,
In the United States, call:
GE Answer Center®
800.626.2000
24 hours a day, 7 days a week
In Canada, write:
Manager, Consumer Relations
2645 Skymark Ave.,
Mississauga, Ontario
Canada L4W 4H2
If you received a damaged
refrigerator…
Immediately contact the dealer
(or builder) that sold you the refrigerator.
Save time and money.
Before you request service…
Check the Problem Solver section in this
guide. It lists minor operating problems that
you can correct yourself.
2
CFC-FREE REFRIGERANT
Your old refrigerator has a cooling system that used CFCs
(chlorofluorocarbons). CFCs are believed to harm stratospheric ozone,
so this refrigerator uses a new refrigerant that does not harm the
stratospheric ozone layer.
If you are throwing away your old refrigerator, make sure the CFC
refrigerant is removed for proper disposal by a qualified servicer. If
you intentionally release this CFC refrigerant you can be subject to
fines and imprisonment under provisions of the federal Clean Air Act.
IF YOU NEED SERVICE
To obtain service, see the Consumer Services
page in the back of this guide.
We’re proud of our service and want you to
be pleased. If for some reason you are not
happy with the service you receive, here are
three steps to follow for further help.
For Customers in the United States:
FIRST, contact the people who serviced your
appliance. Explain why you are not pleased.
In most cases this will solve the problem.
NEXT, if you are still not pleased, write
all the details—including your phone
number—to:
Manager, Consumer Relations
Appliance Park
Louisville, KY 40225
FINALLY, if your problem is still not
resolved, write:
Major Appliance
Consumer Action Panel
20 North Wacker Drive
Chicago, IL 60606
For Customers in Canada:
FIRST, contact the people who serviced your
appliance. Explain why you are not pleased.
In most cases this will solve the problem.
NEXT, if you are still not pleased, write
all the details—including your phone
number—to:
Manager, Consumer Relations
2645 Skymark Ave.,
Mississauga, Ontario
Canada L4W 4H2

3
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using this appliance.
WARNING—When using this appliance,
always exercise basic safety precautions,
including the following:
• Use this appliance only for its intended purpose
as described in this Use and Care Guide.
• This refrigerator must be properly
installed and located in accordance
with the Installation Instructions
before it is used.
• Never unplug your refrigerator by
pulling on the power cord. Always grip
plug firmly and pull straight out from
the outlet.
• Repair or replace immediately all electric
service cords that have become frayed or
otherwise damaged. Do not use a cord that
shows cracks or abrasion damage along its length
or at either the plug or connector end.
• When moving your refrigerator away from the
wall, be careful not to roll over or damage the
power cord.
• Do not allow children to climb, stand or
hang on the shelves in the refrigerator. They
could damage the refrigerator and seriously
injure themselves.
• If your old refrigerator is still around
the house but not in use, be sure to
remove the doors. This will reduce the
possibility of danger to children.
• After your refrigerator is in operation, do
not touch the cold surfaces in the freezer
compartment, particularly when hands are
damp or wet. Skin may adhere to these extremely
cold surfaces.
• If your refrigerator has an automatic icemaker,
avoid contact with the moving parts of the ejector
mechanism, or with the heating element that
releases the cubes. Do not place fingers or hands
on the automatic icemaking mechanism while the
refrigerator is plugged in.
• Don’t refreeze frozen foods which have thawed
completely. The United States Department of
Agriculture in Home and Garden Bulletin
No. 69 says:
‘‘…You may safely refreeze frozen foods that
have thawed if they still contain ice crystals or if
they are still cold—below 40°F. (4°C.).
‘‘…Thawed ground meats, poultry or fish that
have any off-odor or off-color should not be
refrozen and should not be eaten. Thawed ice
cream should be discarded. If the odor or color of
any food is poor or questionable, get rid of it. The
food may be dangerous to eat.
‘‘Even partial thawing and refreezing reduces the
eating quality of foods, particularly fruits,
vegetables and prepared foods. The eating quality
of red meats is affected less than that of many
other foods. Use refrozen foods as soon as
possible to save as much of their eating quality as
you can.’’
• Unplug your refrigerator before cleaning
and making repairs. NOTE: We strongly
recommend that any servicing be
performed by a qualified individual.
• Before replacing a burned-out light bulb, the
refrigerator should be unplugged in order to avoid
contact with a live wire filament. (A burned-out
light bulb may break when being replaced.)
NOTE: Turning control to OFF position does
not remove power to the light circuit.
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
SAVE THESE
INSTRUCTIONS
Important Safety Instructions

OPERATING YOUR REFRIGERATOR
Set the Temperature Controls (appearance may vary)
4
The temperature controls let you regulate the temperature in the fresh
food and freezer compartments. The coldest settings are “E” and “9”.
At first, set the Fresh Food control at “5” and the Freezer control at “C”.
Allow 24 hours for the temperature to stabilize, whether you are
setting the controls for the first time or adjusting them later. Then, if
you want colder or warmer temperatures in either compartment, adjust
the controls one step at a time.
NOTE: Moving the Fresh Food control to OFF turns off cooling in
both compartments—fresh food and freezer—but does not shut off
power to the refrigerator.
FREEZER FRESH FOOD
C INITIAL SETTING
E COLDEST INITIAL SETTING 5
COLDEST 9
ABCDE
ALLOW 24 HOURS FOR TEMPERATURE TO STABILIZE
TEMPERATURE CONTROLS
1
3
5
7
9
F
F
O
How to Test Temperatures
Use the milk test for the fresh food compartment. Place a container
of milk on the top shelf in the fresh food compartment. Check it a day
later. If the milk is too warm or too cold, adjust the temperature controls.
Use the ice cream test for the freezer compartment. Place a
container of ice cream in the center of the freezer compartment. Check
it after a day. If it’s too hard or too soft, adjust the temperature controls.
Always allow 24 hours for the refrigerator to reach the
temperature you set.
Automatic Energy Saver System No Defrosting
You won’t find an “energy saver” switch on this refrigerator.
Warm liquid from the refrigerator’s condenser is automatically
circulated around the front edge of the freezer compartment to help
keep moisture from forming on the outside of the refrigerator during
humid weather.
Many refrigerators use special electric heaters. This refrigerator
needs none. That’s why there is no “energy saver” switch…there’s
no need for it.
It is not necessary to defrost the freezer or fresh food compartments.
Your refrigerator is designed and equipped to defrost itself automatically.
If you turn your household thermostat below 60°F. (16°C.) at night…
…you may want to move the freezer control 1 step
colder. Cooler temperatures in the house may cause
the compressor to operate less frequently, thus
allowing the freezer compartment to warm
somewhat. To protect your frozen food supply,
leave the freezer setting at this colder setting for the
entire winter or for as long as you keep your
thermostat turned down.
Moving the freezer control to colder setting should have no effect on
your fresh food compartment. However, if freezing occurs, move the
fresh food control one step warmer.
When you stop turning the thermostat down, turn the refrigerator’s
controls back to their regular settings.

If you use your refrigerator before the water
connection is made, raise the ice access door
and make sure the icemaker feeler arm is in the
STOP (up) position. When the water supply has
been connected to the icemaker, move the feeler
arm to the ON (down) position.
At first there will be a delay before water is dispensed and ice is made.
On models with a water dispenser, if no
water is dispensed when the refrigerator is
first installed, there may be air in the water line
system. Press the dispenser pad for at least two
minutes to remove trapped air from the water
line and to fill the water system.
The ice cube mold will automatically fill with water AFTER cooling
to freezer temperatures. The first cubes normally freeze after
several hours.
NOTE: With a newly-installed refrigerator, allow about 24 hours
for the freezer compartment to get cold enough to make ice.
(continued next page)
WAT
ER C
RU
S
HE
D
C
U
BE
D
ICE
LIGHT OFF ON
AUTOMATIC ICEMAKER & DISPENSER
(on some models)
How They Work
The automatic icemaker makes ice continually. The dispenser
dispenses water, ice cubes or crushed ice through the freezer
compartment door. Here’s how they work.
Water flows from the household supply through a
(1) dual solenoid valve
to the
(2) water tubing and
to the
(3) automatic icemaker
as needed.
Water is frozen in the
(4) cube mold and
ejected into the
(5) storage bin where
a motor-powered
auger moves
cubes forward.
Cubes fall through the chute in the door when the dispenser
pad is pressed.
When CRUSHED is selected (on some models), a baffle channels
cubes through the crusher and crushed ice falls through a chute into
the glass.
When WATER is selected (on some models), water flows
through the
(6) tubing in the door and is dispensed when the dispenser
pad is pressed.
(7) A light switch (on some models) turns the night light in the
dispenser on or off.
The light also comes on when the dispenser pad is pressed.
The light in the dispenser should be replaced with a 7 watt maximum
bulb when it burns out.
5
3
7
6
4
5
1
2
Important Facts about Your Ice & Water Dispenser
• If this is your first icemaker you’ll hear occasional sounds that
may be unfamiliar. These are normal icemaking sounds and are not
cause for concern.
• Your icemaker will produce 8 cubes per cycle—approximately
120 cubes in a 24-hour period—depending on freezer compartment
temperature, room temperature, number of door openings and other
use conditions.
• Intermittent dispensing of ice is normal. If ice flow interruption is
more than brief, ice clump(s) may be the cause and should be
removed following instructions in this section.
• Avoid overfilling glasses with ice and using narrow or extra-tall
glasses. This can jam the chute or cause the door in the chute to
freeze shut. Periodically open the freezer compartment door and look
down into the chute. If ice is blocking the chute, poke it through with
a wooden spoon.
• To help keep bits of ice from being sprayed beyond the glass,
place the glass close to the ice chute—but not so close that it blocks
outcoming ice.
• Fill glasses with ice before adding soda or other beverage mixes.
• Beverages and foods should not be quick-chilled in the ice
storage bin. Cans, bottles or food packages in the storage bin may
cause the icemaker or auger to jam.
• Do not add ice from trays or bags to the storage bin. It may not
crush or dispense well.
Operating Your Refrigerator Automatic Icemaker & Dispenser
Before Using Your Icemaker and Dispenser
Feeler arm in
STOP (up)
position
Feeler arm in
ON (down)
position
Push the dispenser pad
until the water line is filled.

AUTOMATIC ICEMAKER & DISPENSER
(continued)
Once Your Icemaker and Dispenser are in Operation
Throw away the first few batches of ice cubes (16 or 24 cubes). This
will flush away any impurities in the water line. Do the same thing
after vacations or extended periods when ice isn’t used.
On models with a water dispenser, pour the first 6 glassfuls of water in
the kitchen sink. The first water through the system picks up a slight
‘‘plastic’’ taste from the water tubing.
To make sure the bin fills with ice, level the cubes occasionally.
When cubes fall into the bin they may pile up close to the icemaker
and push the feeler arm to the STOP (up) position before the bin gets
full. Keeping the cubes level allows the icemaker to fill the bin.
To Dispense Ice and Water
• Select CUBES, CRUSHED ICE
(on some models) or WATER. • Grip the glass or other container near the rim and press the rim
against the center of the
dispenser pad.
WATER CRUSHEDCUBEDICE LIGHT OFF ON
WATER CR USHED CUBED ICE
LIGHT OFF ON
When Dispensing Ice… When Dispensing Water…
Some crushed ice may be dispensed even though you selected
CUBES. This happens occasionally when a few cubes get channeled
to the crusher.
Sometimes a mound of snow will form on the door in the ice chute.
This condition is normal, and usually occurs when you have dispensed
crushed ice repeatedly. The snow will eventually evaporate.
Sometimes crushed ice will spray beyond the glass. To avoid this,
hold the glass up close to the chute.
The first glass of water dispensed may be warmer than the
following ones. This is normal.
Dispensed water is cool, not iced. For colder water, simply add
crushed ice or cubes before dispensing water.
CAUTION: Never put fingers or other objects into the
dispenser opening.
To Stop Dispensing If Ice Clumps Form in the Storage Bin…
Release pressure from the
dispenser pad and wait a few
seconds to catch the last bits of ice
or drops of water.
There may be some dripping after
dispensing crushed ice or water. If
there is a lot of dripping, the spill
should be wiped dry right away.
Do not pour water in the spill shelf because it is not self draining—
pour it in the kitchen sink. The shelf and its grille should be cleaned
regularly according to Care and Cleaning
instructions. The grille is easily removed
by pressing on the back right corner.
The icemaker ejects cubes in groups of 8, and it is normal for several
cubes to be joined together. However, if you don’t use the ice very
often, ice clumps may form in the storage bin and can clog
the dispenser.
If this happens:
•Remove the storage bin from the freezer.
• Break up ice clumps with your hands. Throw away any clumps that
you can’t break up.
• Replace the bin before the remaining cubes melt and fuse together.
WATER CRUSHEDCUBED ICE
LIGHT OFF ON
Press here to remove grille
Dispenser
pad Dispenser
pad
6

7
To Remove Ice Storage Bin To Replace Ice Storage Bin
Lift the left corner to free the bin from
the shelf. Pull the bin straight out while
supporting it at front and back.
Slide the bin back until the tab on the bin locks
into the slot in the shelf.
If the bin does not go all the way back, remove
it and turn the drive mechanism 1/4 turn. Then
push the bin back again until the tab on the
bin locks into the slot in the shelf.
Rotate
Drive
Mechanism
If Ice Is Not Used Often…
‘‘Old’’ ice cubes will become cloudy and taste stale. Empty ice
storage bin periodically and wash it in lukewarm water. Be sure to
allow storage bin to cool before replacing it—otherwise ice cubes will
stick to the metal auger.
Move Feeler Arm to STOP (up) Position when…
• Home water supply is to be turned off for several hours.
• Ice storage bin is to be removed for a period of time.
• Going away on vacation, at which time you should also turn off the
valve in the water supply line to your refrigerator.
• Turning the fresh food control to the OFF position.
Water Filter Accessory
Your ice cubes can only be as fresh-tasting as the water that produces them.
That’s why it’s a good idea to purify your water with a water filter.
REMOVES SEDIMENT
Rigid, porous graded density depth cellulose
fiber cartridge catches dirt, rust particles, sand and silt.
REMOVES ODORS
Activated charcoal granules remove
musty, stale odors.
IMPROVES TASTE
Activated charcoal granules remove oily,
medicinal, plastic and metallic tastes.
REDUCES SCALE
Special crystals reduce hard scale deposit formation.
The water filter is an option at extra cost and is available from your dealer.
Specify WR97X0214. It has complete installation instructions and installs
in minutes on 1/4″O.D. copper water line.
Ice Trays (on some models)
To release ice cubes, invert tray, hold it
over storage bin or bowl, and twist at
both ends.
For only one or two ice cubes, leave
tray right-side up, twist both ends
slightly and remove desired number
of cubes.
Wash ice trays and storage bin in
lukewarm water only. Do not put
them in an automatic dishwasher.
ICE SERVICE
Water Supply Kit Automatic Icemaker Accessory Kit
A kit containing copper tubing, shut-off valve fittings and instructions
needed to connect the icemaker to your cold water line is available at
extra cost. See Preparation section.
If your refrigerator did not come already equipped with an automatic
icemaker, an Icemaker Accessory Kit is available at extra cost. Check the
back of the refrigerator for the specific icemaker kit needed for your model.
ACCESSORIES
Automatic Icemaker & Dispenser Ice Service Accessories

FOOD STORAGE SUGGESTIONS
8
Suggested storage times for meat and poultry*
Eating quality DAYS IN MONTHS IN
drops after REFRIGERATOR FREEZER
time shown AT 35° to 40° F. AT 0° F.
(2° to 4° C.) (-18° C.)
Eating quality DAYS IN MONTHS IN
drops after REFRIGERATOR FREEZER
time shown AT 35° to 40° F. AT 0° F.
(2° to 4° C.) (-18° C.)
Fresh Meats
Roasts (Beef & Lamb) ...................... 3 to 5 ...........................6 to 12
Roasts (Pork & Veal)........................ 3 to 5 ...........................4 to 8
Steaks (Beef) .................................... 3 to 5 ...........................6 to 12
Chops (Lamb)................................... 3 to 5 ...........................6 to 9
Chops (Pork) .................................... 3 to 5 ...........................3 to 4
Ground & Stew Meats ...................... 1 to 2 ...........................3 to 4
Variety Meats.................................... 1 to 2 ...........................3 to 4
Sausage (Pork)................................. 1 to 2 ...........................1 to 2
Processed Meats
Bacon ................................................... 7...................................1
Frankfurters.......................................... 7 .................................1/2
Ham (Whole)........................................ 7...............................1 to 2
Ham (Half) ........................................ 3 to 5 ...........................1 to 2
Ham (Slices)......................................... 3...............................1 to 2
Luncheon Meats ............................... 3 to 5..........Freezing not recommended.
Sausage (Smoked)............................... 7..............Freezing not recommended.
Sausage (Dry & Semi-Dry) .............14 to 21 ........Freezing not recommended.
Cooked Meats
Cooked Meats and Meat Dishes........ 3 to 4 ...........................2 to 3
Gravy & Meat Broth.......................... 1 to 2 ...........................2 to 3
Fresh Poultry
Chicken & Turkey (Whole)................ 1 to 2..............................12
Chicken (Pieces)............................... 1 to 2 ...............................9
Turkey (Pieces)................................. 1 to 2 ...............................6
Duck & Goose (Whole)..................... 1 to 2...............................6
Giblets............................................... 1 to 2 ...............................3
Cooked Poultry
Pieces (Covered with Broth) ..............1 to 2................................6
Pieces (Not Covered)........................ 3 to 4...............................1
Cooked Poultry Dishes ..................... 3 to 4 ...........................4 to 6
Fried Chicken .................................... 3 to 4 ...............................4
(Other than for meats & poultry) FREEZER
Most fruits and vegetables................................................8-12 months
Lean fish.............................................................................6-8 months
Fatty fish, rolls and breads, soups, stew, casseroles .........2-3 months
Cakes, pies, sandwiches, leftovers (cooked),
ice cream (original carton) ............................................1 month max.
Meats, fish and poultry purchased from the store vary in quality and age;
consequently, safe storage time in your refrigerator will vary.
*U.S. Department of Agriculture
Fresh Food Storage Tips
To store vegetables:
•Use the vegetable drawers—they have been
designed to preserve the natural moisture
and freshness of produce.
•Covering vegetables with a moist towel
helps maintain crispness.
•As a further aid to freshness,
prepackaged vegetables can be
stored in their original wrapping.
Unfrozen meats, fish, and poultry:
•Always remove store wrappings.
•Rewrap in foil, plastic wrap or wax paper
and refrigerate immediately.
Cheese:
•Wrap well with wax paper or aluminum
foil, or put in a plastic bag.
•Carefully wrap to expel air and help
prevent mold.
•Store prepackaged cheese in its own
wrapping if you wish.
Tips on Freezing Foods
There are 3 essential requirements for efficient home freezing.
1. Initial quality. Freeze only top-quality foods. Freezing retains
quality and flavor; it cannot improve quality.
2. Speed. The quicker fruits and vegetables are frozen after picking,
the better the frozen product will be. You’ll save time, too, with less
culling and sorting to do.
3. Proper packaging. Use food wraps designed especially
for freezing.
To freeze meat, fish and poultry, wrap well in freezer-weight foil (or
other heavy-duty wrapping material), forming it carefully to the shape
of the contents. This expels air. Fold and crimp ends of the package to
provide a good, lasting seal. Don’t refreeze meat that has been
completely thawed; meat, whether raw or cooked, can be frozen
successfully only once.
Fine-quality ice cream, with high cream content, will normally
require slightly lower temperatures than more “airy” already-packaged
brands with low cream content.
•It will be necessary to experiment to determine the freezer
compartment location and temperature control setting to keep your
ice cream at the right serving temperature.
•The rear of the freezer compartment is slightly colder than the front.
New techniques are constantly being developed. Consult the County
Extension Service or your local Utility Company for the latest
information on freezing and storing foods.

STORAGE DRAWERS
Fruit & Vegetable Drawer (on some models) Convertible Meat Drawer (on some models)
9
This refrigerated drawer keeps unwrapped foods fresh by retaining the
natural moisture content of foods such as:
• Artichokes • Cherries • Plums • Asparagus
• Corn • Radishes • Beets, topped • Currants
• Rhubarb • Blueberries • Greens, leafy • Spinach
• Carrots • Lettuce • Tomatoes, ripe • Celery
• Parsley • Peas, green
As in any refrigerated storage area, it is recommended that foods with
strong odors be stored wrapped—foods such as:
• Broccoli • Cabbage • Parsnips • Brussels sprouts
• Cauliflower • Turnips • Green onions
Storage time will depend upon the type of food and its condition when
placed in the drawers.
Excess water that may accumulate in the bottom of the drawer should
be emptied and the drawer wiped dry. The drawer is partially sealed
by gaskets attached to the cover. Always replace the drawer in this
cover and push the drawer all the way in.
The Convertible Meat Drawer has its own cold air duct to allow
a stream of cold air from the freezer compartment to flow around
the drawer.
The variable temperature control regulates the air flow from the
freezer compartment.
Set control lever down to the
coldest setting to store fresh meats.
If lever is left in meat position for
a long period of time, some
frost may form on the inside
of the drawer.
Set control lever up to convert
the drawer to normal refrigerator
temperature and provide extra
vegetable storage space. Cold air
duct is turned off. Variable settings
between these extremes can be selected.
Sealed Snack Pack (on some models) Adjustable Humidity Drawers (on some models)
The sealed Snack Pack—and shelf to which it is attached—can be
relocated within the Fresh Food compartment. The sealed drawer
retains sufficient humidity for convenient storage of lunch meats,
cheese, hors d’oeuvres, spreads and snacks.
These drawers have individual, adjustable humidity controls that let
you regulate the amount of moisture retained in foods.
Slide the control all the way
to the VEG HIGH setting and
the drawer provides high
humidity recommended for
most vegetables.
Slide the control all the way
to the FRUIT LOW setting to
provide lower humidity levels
recommended for most fruits.
HUMIDITY STORAGE
VEG HIGH FRUIT LOW
Food Storage Suggestions Storage Drawers
TEMP
Fruit & Vegetable
Drawer
Convertible
Meat Drawer
Normal
setting
Coldest
setting

SHELVES
How to Rearrange Your Shelves
10
Shelves in the fresh food compartment are adjustable, enabling
you to make efficient shelf arrangements to fit your family’s food
storage needs.
To remove shelves:
Tilt the shelf up at front,
then lift it up and out of the
tracks on the rear wall of
the refrigerator.
To relocate shelves:
Select desired shelf height.
With shelf front raised
slightly, engage the top
hooks in the tracks at the
rear of the cabinet. Then
lower the front of the shelf
until it locks into position.
Wire shelves (on some
models) are adjustable in the same manner.
Lift up
and out
2Tilt up
1Lower to
lock into place
2
Engage
top hook
1
Bins on Fresh Food Compartment Door (on some models)
Adjustable bins can easily be carried from refrigerator to work area.
To remove:
Lift bin straight up until
mounting hooks disengage.
To replace or relocate:
Select desired shelf height,
engage bin’s hook in slots
on the tracks of the door,
and push in. Bin will lock
in place.
The divider (on some models) helps prevent tipping, spilling or
sliding of small items stored on the door shelf. Place index finger and
middle finger on either side of the divider near the front and simply
move it back and forth to fit your needs.
Divider
Removable Shelves in Freezer Compartment
Shelves in the freezer compartment are easily removed and replaced.
To remove:
1. While pressing the tabs on the shelf
supports on the right wall, lift the shelf
out of the grooves in the supports.
2. Pull the shelf sideways until the rods
come out of the holes on the left wall.
To replace shelves:
Insert the rods into the holes. Then, while
pressing the tabs, lower the shelf into the
grooves in the supports. Be sure the shelf
wire is fully inserted into the grooves.

CARE AND CLEANING
Cleaning—Outside
11
The water and ice dispenser spill shelf should be wiped dry
immediately to prevent spotting. Water left on the shelf may leave
deposits that you can remove by soaking with undiluted vinegar. You
can also use a paste of non-precipitating water softener (such as
Calgon brand) and water, or 1 teaspoon (5 ml) of citric acid powder
per pint (500 ml) of hot tap water. Soak until the deposit disappears or
becomes loose enough to rinse away. Usually 30 minutes soaking time
is adequate. Avoid using wax on the spill shelf and trim.
The door handles and trim can be cleaned with a cloth dampened
with a solution of mild liquid dishwashing detergent and water. Dry
with a soft cloth. Don’t use wax on the door handles and trim.
Keep the finish clean. Wipe with a clean cloth lightly dampened with
kitchen appliance wax or mild liquid dishwashing detergent. Dry and
polish with a clean, soft cloth. Do not wipe the refrigerator with a
soiled dishwashing cloth or wet towel. These may leave a residue that
can erode the paint. Do not use scouring pads, powdered cleaners,
bleach or cleaners containing bleach because these products can
scratch and weaken the paint finish.
Protect the paint finish. The finish on the outside of the refrigerator
is a high quality, baked-on paint finish. With proper care, it will stay
new-looking and rust-free for years. Apply a coat of kitchen/appliance
wax when the refrigerator is new and then at least twice a year.
Appliance Polish Wax & Cleaner is available from Service and
Parts Centers.
Shelves Care and Cleaning
Cleaning—Inside
Inside the fresh food and freezer compartments should be cleaned
at least once a year. Unplug the refrigerator before cleaning. If this is
not practical, wring excess moisture out of sponge or cloth when
cleaning around switches, lights or controls.
Use warm water and baking soda solution—about a tablespoon
(15 ml) of baking soda to a quart (1 L) of water. This both cleans and
neutralizes odors. Rinse thoroughly with water and wipe dry.
Other parts of the refrigerator—including door gaskets, meat and
vegetable drawers, ice storage bin and all plastic parts—can be
cleaned the same way. After cleaning door gaskets, apply a thin layer
of petroleum jelly to the door gaskets at the hinge side. This helps
keep the gaskets from sticking and bending out of shape. Do not use
cleansing powders or other abrasive cleaners.
Avoid cleaning cold glass shelves with hot water because the extreme
temperature difference may cause them to break.
To help prevent odors, leave an open box of baking soda in the
rear of the refrigerator, on the top shelf. Change the box every 3
months. An open box of baking soda in the freezer will absorb stale
freezer odors.
Drain opening in freezer compartment.
During yearly cleaning, remove bottom freezer
basket and flush a solution of baking soda—
1 teaspoon (5 ml) and 2 cups (500 ml) of hot (not
boiling) water—through the drain line with the
help of a meat baster. This will help eliminate
odor and reduce the likelihood of a clogged drain
line. If drain becomes clogged, use a meat baster
and baking-soda-and-water solution to force the
clog through the drain line.
Do not wash any plastic parts from your refrigerator in
your automatic dishwasher.
Behind Refrigerator Under Refrigerator
Care should be taken in moving your refrigerator away from the wall.
All types of floor coverings can be damaged, particularly cushioned
coverings and those with embossed surfaces. Pull the refrigerator
straight out and return it to position by pushing it straight in. Moving
your refrigerator in a side direction may result in damage to your floor
covering or refrigerator.
When pushing the refrigerator back, make sure you don’t roll over the
power cord or icemaker supply line (on some models).
For most efficient operation,
you need to keep the area under the
refrigerator clean. For best results,
use a brush specially designed for this
purpose. It is available at most
appliance parts stores. This easy
cleaning operation should be done
at least once a year.
(continued next page) Clean the condenser coils
at least once a year.

CARE AND CLEANING
(continued)
Drawer Removal
Light Bulb Replacement
Fresh Food Compartment–Upper Light
1. Unplug refrigerator.
2. To align the control knob
properly, note position of
numbered control for proper
reassembly, turn control to
OFF and pull off knob.
3. Pull bottom of light panel
down about 1/4 inch (6 mm)
just enough to disengage lip at
rear from grooves in retainers
on rear wall.
4. Lift panel to disengage top from pins on side walls and
remove panel.
After replacing with same size bulb, reinstall panel (hang top on pins;
pull bottom down, push it back and release it to let lip engage grooves
in retainers). Replace temperature control knob in OFF position, turn
it to previous setting and plug refrigerator back in.
Freezer Compartment
1. Unplug the refrigerator.
2. Remove the shelf just below light shield. (The shelf will be easier
to remove if it is emptied first.)
3. Pull the light shield toward you to reach the bulb.
After replacing with same size bulb, reinstall shelf and plug the
refrigerator back in.
FREEZER FRESHFOOD
C INITIALSETTING
E COLDEST INITIALSETTING 5
COLDEST 9
ABCDE
ALLOW24 HOURS FOR TEMPERATURE TO STABILIZE
TEMPERATURE CONTROLS
1
3
5
7
9
F
F
O
12
Grooved
retainer,
one on
each side
Pin
Drawers will stop before coming all the way out of refrigerator to help
prevent contents from spilling onto floor. Drawers can easily be
removed by tilting up slightly and pulling past “stop” location.
On some models you may need to remove the door bins from the fresh
food door before removing the drawers.
If the door prevents you from taking out the drawers, the refrigerator
will need to be rolled forward until the door opens enough to slide the
drawers out. In some cases when you roll the refrigerator out you will
need to move the refrigerator to the left as you roll it out.
Drawer guides
Left side
When replacing the drawers, make sure you slide them through the
drawer guides on the left side.

PREPARATION
Preparing for Vacation Preparing to Move
13
For shorter vacations, remove perishable foods and leave controls
at regular settings. However, if room temperature is expected to
drop below 60°F. (16°C.), follow same instructions in Temperature
Control section.
For long vacations or absences, remove food and shut off power to
refrigerator. Move the freezer control to OFF position and clean
interior with baking soda solution of 1 tablespoon (15 ml) of soda to
1 quart (1 L) of water. Wipe dry. To prevent odors, leave open box of
soda in refrigerator. Leave doors open.
Move the icemaker (on some models) feeler arm to STOP (up)
position and be sure to shut off water supply to the refrigerator.
Disconnect power cord from wall outlet, remove all food, and clean
and dry the interior.
Secure all loose items such as grille, shelves and storage pans by
taping them securely in place to prevent damage.
Be sure refrigerator stays in upright position during actual moving and
in van. Refrigerator must be secured in van to prevent movement.
Protect outside of refrigerator with blanket.
Care and Cleaning Preparation
Refrigerator Location Clearances
Do not install refrigerator where temperature will be below
60°F. (16°C.) because it will not run often enough to maintain
proper temperatures.
Do install it on a floor strong enough to support a fully loaded
refrigerator.
Allow the following clearances for ease of installation, proper air
circulation, plumbing and electrical connections.
Sides ..................................................................5/8″ (15 mm)
Top ....................................................................1″ (25 mm)
If the refrigerator is against a wall on either side, allow the
following door clearances:
for 19, 20, 22 and 24 models .............................3/4″(19 mm)
for 27 models.....................................................11⁄2″(38 mm)
Back ..................................................................1″ (25 mm)
(If built-in, allow 7⁄8
″ [22 mm] for hinge covers.)
Rollers Leveling
Adjustable rollers behind the base
grille enable you to move the
refrigerator away from the wall for
cleaning. These rollers should be set
so the refrigerator rests firmly on the
floor. To assure that the doors will
close automatically from a half-way-
open position, there is a built-in tilt
from the front to the back of the
cabinet. Side-by-side refrigerators also
have specially designed door hinges that lift both doors slightly when
opened, allowing the force of gravity to help close them securely.
To adjust rollers, remove the base
grille by grasping it at the bottom and
pulling it out.
Turn the roller adjusting screws
clockwise to raise the refrigerator,
counterclockwise to lower it. Use an
adjustable wrench (3/8″hex head bolt)
or pliers.
When leveling, you can improve door closure by raising the front
approximately 5/8″(15 mm) from the floor.
To replace base grille, align prongs on back of grille with clamps in
cabinet and push forward until grille snaps into place.
Water Supply to Icemaker
If your refrigerator has an icemaker, or if you plan to add an icemaker later, the icemaker will
have to be connected to a cold water line. A water supply kit containing copper tubing, shut-off
valve, fittings and instructions is available at extra cost from your dealer. There should be sufficient
tubing for the icemaker from the cold water supply to allow you to move the refrigerator out from
the wall several feet (approximately 8 feet [244 cm] of 1/4″copper tubing in three 10-inch [25 cm]
diameter coils).

INSTALLATION REQUIREMENTS
IMPORTANT…PLEASE READ CAREFULLY
How to Connect Electricity
14
For personal safety, this
appliance must be
properly grounded.
The power cord of this
appliance is equipped with a
3-prong (grounding) plug
which mates with a standard
3-prong (grounding) wall
outlet to minimize the
possibility of electric shock
hazard from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to
make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is your
personal responsibility and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE
THE THIRD (GROUND) PRONG FROM THE POWER CORD.
Preferred method
Insure proper
grounding exists
before using.
Use of Adapter Plug
Because of potential
hazards under certain
conditions, we strongly
recommend against use
of an adapter plug.
However, if you still elect
to use an adapter, where
local codes permit, a
TEMPORARY
CONNECTION may be
made to a properly
grounded 2-prong
wall outlet by use of
a UL listed adapter
available at most local
hardware stores.
The larger slot in the adapter must be aligned with the larger slot in
the wall outlet to provide proper polarity in the connection of the
power cord.
Use of an adapter plug will increase the clearance needed for the back
of the refrigerator.
CAUTION: Attaching the adapter ground terminal to a wall outlet
cover screw does not ground the appliance unless the cover screw is
metal, and not insulated, and the wall outlet is grounded through the
house wiring. You should have the circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
When disconnecting the power cord from the adapter, always hold
the adapter in place with one hand while pulling the power cord plug
with the other hand. If this is not done, the adapter ground terminal is
very likely to break with repeated use.
Should the adapter ground terminal break, DO NOT USE the
appliance until a proper ground has again been established.
Temporary Method
(Adapter plugs not
permitted in Canada.)
Align large prongs/slots.
Insure proper grounding and firm
connection exists before use.
Electrical Requirements Use of Extension Cords
The refrigerator should always be plugged into its own individual
electrical outlet which has a voltage rating that matches the rating plate.
This provides the best performance and also prevents overloading house
wiring circuits which could cause a fire hazard from overheated wires.
Because of potential safety hazards under certain conditions, we
strongly recommend against the use of an extension cord. However, if
you still elect to use an extension cord, it is absolutely necessary that it
be a UL-listed 3-wire grounding type appliance extension cord having
a grounding type plug and outlet and that the electrical rating of the
cord be 15 amperes (minimum) and 120 volts.
Use of an extension cord will increase the clearance needed for the
back of the refrigerator.

WATER LINE INSTALLATION INSTRUCTIONS
15
INSTALL THE SHUTOFF VALVE ON THE
NEAREST FREQUENTLY USED DRINKING
WATER LINE.
a. Choose a location for the valve that is easily
accessible. It is best to connect into the side of
a vertical water pipe. When it is necessary to
connect into a horizontal water pipe, make the
connection to the top or side, rather than at the
bottom, to avoid drawing off any sediment from
the water pipe.
b. Drill a 1/4″hole in the water pipe, using a
sharp bit. Remove any burrs resulting from
drilling the hole in the pipe. (Do not drill a hole
if the valve is a self-piercing type.)
c. Fasten the
shutoff valve to
the cold water pipe
with the pipe clamp.
d. Tighten the
clamp screws until the
sealing washer begins to
swell. Do not overtighten
or you may crush the
copper tubing.
2
CAUTION:
• If you use your refrigerator before connecting
the water line, make sure the icemaker feeler arm
is kept in the STOP (up) position.
• Do not install the icemaker tubing in areas
where temperatures fall below freezing.
•When using any electrical device (such as a
power drill) during installation, be sure the device
is insulated or wired in a manner to prevent the
hazard of electric shock.
• All installations must be in accordance with
local plumbing code requirements.
WARRANTY INFORMATION
This water line installation is not warranted by
the refrigerator or icemaker manufacturer.
Follow these instructions carefully to minimize
the risk of expensive water damage.
WHAT YOU WILL NEED
• A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 20 and 120 p.s.i.
•
Power drill, unless you have a self-piercing valve.
• Copper tubing, 1/4″outer diameter to connect
the refrigerator to the water supply. Be sure both
ends of the tubing are cut square.
To determine how much copper tubing you need:
measure the distance from the water valve on the
back of the refrigerator to the water supply pipe.
Then add 8 feet (244 cm). Be sure there is
sufficient extra tubing (about 8 feet [244 cm]
coiled into 3 turns of about 10 inches [25 cm]
diameter) to allow the refrigerator to move out
from the wall after installation. Do not use plastic
tubing or plastic fittings because the water supply
line is under pressure at all times. Also, certain
types of plastic tubing may become brittle with
age and crack, resulting in water leakage.
•Shutoff valve to connect to the cold water line.
The shut-off valve should have a water inlet with
a minimum inside diameter of 5/32″at the point
of connection to the COLD WATER LINE. Saddle-
type shut-off valves are included in many water
supply kits. Before purchasing, make sure a
saddle-type valve complies with your local
plumbing codes.
• Two 1/4″ outer diameter compression nuts
and 2 ferrules (sleeves)—to connect the copper
tubing to the shutoff valve and the refrigerator
water valve.
• If your existing water line has a flared fitting at
the end, you will need an adapter (available at
plumbing supply stores) to connect the water line
to the refrigerator OR—you can cut off the flared
fitting with a tube cutter and then use a
compression fitting.
SHUT OFF THE MAIN WATER SUPPLY.
Turn on the nearest faucet long enough to clear
the line of water.
1
Typical ways to connect to water supply
Under sink
to cold
water pipe
Through wall to
utility room cold
water pipe
In crawl
space under
house
Through floor
to basement
cold water pipe
Pipe
clamp
Saddle type
shutoff
valve
Washer
Inlet
end
Vertical
cold water
pipe
(continued next page)

16
WATER LINE INSTALLATION INSTRUCTIONS
(continued)
CONNECT THE COPPER TUBING TO
THE REFRIGERATOR.
Before making the connection to the
refrigerator, be sure the refrigerator power
cord is not plugged into the wall outlet.
We recommend installing a water filter
(available at Service and Parts Centers) if your
water supply has sand or particles that could clog
the screen of the refrigerator’s water valve. Install
it in the water line near the refrigerator.
6
ROUTE THE COPPER TUBING BETWEEN THE
COLD WATER LINE AND THE REFRIGERATOR.
Route the tubing through a hole drilled in the
floor or wall (behind the refrigerator or adjacent
base cabinet) as close to the wall as possible. Be
sure there is sufficient extra tubing (about 8 feet
[244 cm] coiled into 3 turns of about 10″[25 cm]
diameter) to allow the refrigerator to move out
from the wall after installation.
3a. Remove the plastic flexible cap from the
water valve.
b. Place the
compression nut
and ferrule
(sleeve) onto the
end of the tubing
as shown.
c. Insert the end
of the copper
tubing into the
water valve
connection as far
as possible. While holding
the tubing, tighten the fitting.
d. Fasten the copper tubing into the clamp
provided to hold it in a vertical position. You may
need to pry open the clamp.
TURN THE WATER ON AT THE
SHUTOFF VALVE.
Tighten any connections that leak.
7
MOVE THE REFRIGERATOR BACK TO
THE WALL.
Arrange the coil of copper tubing so that it does
not vibrate against the back of the refrigerator or
against the wall.
10
SET THE ICEMAKER FEELER ARM TO THE ON
(DOWN) POSITION.
The icemaker will not begin to operate until it
reaches its operating temperature of 15°F. (-9°C.)
or below. It will then begin operation automatically
if the icemaker is in the ON (down) position.
NOTE: The icemaker may double-cycle when it
first starts, causing some water spillage from the
icemaker into the ice bucket. This is normal and
should not happen again. The first few batches of
cubes should be thrown away, so that remaining
impurities in the water line will be flushed out.
9
PLUG THE REFRIGERATOR POWER CORD
INTO A GROUNDED ELECTRICAL OUTLET.
8
CONNECT THE COPPER TUBING TO THE
SHUTOFF VALVE.
Place the compression
nut and ferrule (sleeve)
onto the end of the
tubing and connect it to
the shutoff valve. Make
sure the tubing is fully
inserted into the valve.
Tighten the compression
nut securely.
4
TURN ON THE WATER AND FLUSH OUT
THE TUBING.
a. Turn the main water supply on and flush out
the tubing until the water is clear.
b. Shut the water off at the water valve after
about one quart of water has been flushed
through the tubing.
5
Saddle type
shutoff valve
Packing nut
Outlet valve
Compression nut
Ferrule
(sleeve)
Ferrule
(sleeve)
1/4″ Copper tubing
1/4″ Compression nut
Tubing
clamp
Refrigerator connection

QUESTIONS?
USE THIS PROBLEM SOLVER
NORMAL OPERATING SOUNDS
These sounds are normal and do not indicate a need for service.
The new high efficiency compressor runs faster and will have a higher
pitch hum or pulsating sound while operating.
Defrost timer and refrigerator control clicks on and off.
The fan circulating air inside the freezer which keeps the
temperatures throughout.
Water dropping on the defrost heater causing a
sizzling, hissing or popping sound during the defrost cycle.
The flow of refrigerant through the freezer cooling
coil sounds like boiling water or a gurgling noise.
Cracking or popping of cooling coils caused by expansion
and contraction during defrost and refrigeration following defrost.
Water dripping as it melts from the evaporator
and flows to the drain pan during the defrost cycle.
Icemaker (on some models)
The icemaker water valve will buzz when the icemaker fills
with water. If the feeler arm is in the ON (down) position it will buzz even if it has
not yet been hooked up to water. Keeping the feeler arm in the ON (down) position
before it is hooked up to water can damage the icemaker. To prevent this, raise the
feeler arm to the STOP (up) position. This will stop the buzzing.
The sound of cubes dropping into the bin and water running in pipes as icemaker refills.
(continued next page)
PROBLEM POSSIBLE CAUSE
REFRIGERATOR • May be in defrost cycle when motor does not operate for about 30 minutes.
DOES NOT OPERATE • Temperature control in OFF position.
• If interior light is not on, refrigerator may not be plugged in at wall outlet.
• If plug is secure and the refrigerator still fails to operate, plug a lamp or a small
appliance into the same outlet to determine if there is a tripped circuit breaker or
burned out fuse.
MOTOR OPERATES • Modern refrigerators with more storage space and a larger freezer
FOR LONG PERIODS compartment require more operating time.
• Normal when refrigerator is first delivered to your home—usually requires 24
hours to completely cool down.
• Large amounts of food placed in refrigerator to be cooled or frozen.
• Hot weather—frequent door openings.
• Door left open.
• Temperature controls are set too cold. Refer to instructions for use
of Temperature Controls.
• Grille and condenser need cleaning. Refer to Care and Cleaning page.
MOTOR STARTS & • Temperature control starts and stops motor to maintain even temperatures.
STOPS FREQUENTLY
VIBRATION OR • If refrigerator vibrates, more than likely it is not resting solidly on the floor and
RATTLING fron
t roller screws or front leveling legs need adjusting, or floor is weak or uneven.
Refer to Rollers in the Preparation section.
• If dishes vibrate on shelves, try moving them. Slight vibration is normal.
Water Line Installation Problem Solver
17

PROBLEM SOLVER
(continued)
18
PROBLEM POSSIBLE CAUSE
HOT AIR FROM • Normal air flow cooling motor. In the refrigeration process, it is normal that heat
BOTTOM OF be expelled in the area under the refrigerator. Some floor coverings will discolor
REFRIGERATOR at these normal and safe operating temperatures. Your floor covering supplier
should be consulted if you object to this discoloration.
DOOR NOT CLOSING • Door gasket on hinge side sticking or folding over. To correct, put a small
PROPERLY amount of petroleum jelly on face of gasket.
FRESH FOOD OR • Temperature control not set cold enough. Refer to Temperature Control section.
FREEZER COMPARTMENT • Warm weather—frequent door openings.
TEMPERATURE • Door left open for long time.
TOO WARM • Package may be holding door open.
FOODS DRY OUT • Foods not covered, wrapped or sealed properly.
FROST OR ICE • Door may have been left ajar or package holding door open.
CRYSTALS ON • Too frequent or too long door openings.
FROZEN FOOD • Frost within package is normal.
SLOW ICE CUBE • Door may have been left open.
FREEZING • Turn temperature of freezer compartment colder.
ICE CUBES HAVE • Old cubes need to be discarded.
ODOR/TASTE • Ice storage bin needs to be emptied and washed.
• Unsealed packages in refrigerator and/or freezer compartments may be
transmitting odor/taste to ice cubes.
• Interior of refrigerator needs cleaning—refer to Care and Cleaning section.
• Poor-tasting incoming water. Install a water filter—see Water Filter
Accessory section.
AUTOMATIC • ON-STOP control in STOP (up) position.
ICEMAKER • Water supply turned off or not connected.
DOES NOT WORK • Freezer compartment too warm.
(on some models) • Cubes too small—water shutoff valve connecting refrigerator to home
water line may be clogged.
• Sometimes cubes fuse to the side of the ice mold and hold the feeler arm in the
STOP (up) position. Remove this ice to restart the icemaker.
• When reaching for cubes by hand, you may have pushed the feeler arm into the
STOP (up) position by mistake.
• Piled up cubes in storage bin may cause icemaker to shut off too soon. With
icemaker feeler arm in STOP (up) position, level cubes in bin.
CUBE DISPENSER • No ice cubes. Remove storage container. If cubes are frozen to wire arm,
DOES NOT WORK remove cubes.
(on some models) • No ice cubes. Icemaker turned off or water supply turned off.
• Irregular ice clumps in storage container. Break up as many as you can with
fingertip pressure and discard the remaining clumps.

19
Problem Solver
PROBLEM POSSIBLE CAUSE
WATER HAS POOR • If the water dispenser has not been used for a long time, dispense water
TASTE/ODOR in regular manner until all water in the system is replenished with fresh water.
(on some models) • Poor-tasting incoming water. Install a water filter—see Water Filter section.
WATER IN FIRST • Allow about 24 hours for water to cool to proper temperature after
GLASS IS WARM refrigerator is first installed.
(on some models) • If water dispenser has not been used for a long time, water in first
glass will not be as cool as in succeeding glasses.
• If the water system has been drained, allow several hours for replenished
supply to chill.
WATER DISPENSER • Water supply line turned off or not connected.
DOES NOT WORK • Supply line may be clogged with sediment.
(on some models) • If no water is dispensed when the refrigerator is first installed, there may be air
in the water system. Press the dispenser pad for at least two minutes to remove
trapped air from the water line and to fill the water system.
DIVIDER BETWEEN • Normal warmth is created by automatic energy saver system circulating warm
FRESH FOOD AND liquid around front edge of freezer compartment to help prevent condensation
FREEZER COMPART- on outside of refrigerator in hot, humid weather.
MENTS FEELS WARM
MOISTURE FORMS • Not unusual during periods of high humidity.
ON OUTSIDE OF
REFRIGERATOR
MOISTURE • Too frequent or too long door openings.
COLLECTS INSIDE • In humid weather, air carries moisture into refrigerator when doors are opened.
WATER ON KITCHEN • The drain in the bottom of the refrigerator may be clogged. Remove any ice on
FLOOR OR ON the freezer bottom and clean the drain. Refer to Care and Cleaning section.
BOTTOM OF FREEZER • When using the dispenser use a glass no taller than six inches (15 cm) tall. A taller
glass may be jamming cubes in the funnel chute. They can fuse inside the chute
and drop out later, leaving water or ice on the floor.
REFRIGERATOR • Foods with strong odors should be tightly covered.
HAS ODOR • Check for spoiled food.
• Interior needs cleaning. Refer to Care and Cleaning section.
• Defrost water system needs cleaning.
• Keep open box of baking soda in refrigerator; replace every 3 months.
INTERIOR LIGHT • No power at outlet.
DOES NOT WORK • Light bulb needs replacing. See Care and Cleaning section.
If you need more help… In the United States call, toll free:
GE Answer Center®800.626.2000 consumer information service
In Canada: Manager Consumer Relations
2645 Skymark Ave., Mississauga (Ontario) Canada L4W 4H2

For Customers With Impaired Hearing…
In the United States: 800-833-4322
Consumers with impaired hearing or speech who have access to a TDD or a conventional teletypewriter may call 800-TDD-GEAC
(800-833-4322) to request information or service.
In Canada contact Manager, Consumer Relations, Camco, Inc.,
2645 Skymark Avenue, Mississauga, Ontario, Canada L4W 4H2
20
We’ll Be There
With the purchase of your new appliance, receive the assurance that if you ever need information
or assistance, we’ll be there. All you have to do is call—or write!
In-Home Repair Service In the United States:
800-GE-CARES (800-432-2737)
Our consumer service professional will provide expert repair service on your new appliance, scheduled at a time that’s convenient for
you. Many GE Consumer Service company-operated locations offer you service today or tomorrow, or at your convenience (7:00 a.m. to
7:00 p.m. weekdays, 9:00 a.m. to2:00 p.m. Saturdays).Our factory-trained technicians know your appliance inside and out—so most
repairs can be handled in just one visit.
In Canada consult your local telephone directory for the Camco Service
or Authorized Service Center nearest you.
GE Answer Center® In the United States: 800.626.2000
Whatever your question about your new major appliance, GE Answer Center® information service is available to help. Your call—and
your question— will be answered promptly and courteously. And you can call any time. GE Answer Center® service is open 24 hours a
day, 7 days a week.
In Canada contact Manager, Consumer Relations, Camco, Inc.,
2645 Skymark Avenue, Mississauga, Ontario, Canada L4W 4H2
Service Contracts In the United States: 800-626-2224
You can have the secure feeling that GE Consumer Service will still be there after your warranty expires. Purchase a GE contract while
your warranty is still in effect and you’ll receive a substantial discount. With a multiple-year contract, you’re assured of future service at
today’s prices.
800-461-3636 In Canada
Parts and Accessories In the United States: 800-626-2002
Individuals qualified to service their own appliances can have needed parts or accessories sent directly to their home. The GE parts
system provides access to over 47,000 Genuine Renewal Parts…and all are fully warranted. VISA, MasterCard and Discover cards
are accepted.
User maintenance instructions contained in this booklet cover procedures intended to be performed by any user. Other servicing
generally should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
In Canada consult your local telephone directory for the Camco Service or Authorized Service
Center nearest you.