GearMo GM-HU32ES User manual

gearmo.com
User Manual
2-Port USB 3.2 Gen 1 Industrial Surface &
DIN-Rail Mount Hub w/ Gigabit Ethernet & DB9 FTDI Serial
Model No. GM-HU32ES

i
Contents
- Introduction .................................................................................................................. 1
- System Requirements .......................................................................................... 1
- Package Contents .................................................................................................... 1
- Hub Layout .................................................................................................................... 2
- Installation ..................................................................................................................... 2
- DIN Rail Mounting ...................................................................................................... 3
- Surface / Wall Mounting ....................................................................................... 4
- Specifi cations .............................................................................................................. 5
- Windows Installation ............................................................................................... 6
gearmo.com/support

1
gearmo.com/support
Introduction
System Requirements
Package Contents
Thank you for purchasing Gearmo’s 2-Port USB 3.2 Gen 1 Industrial Surface & DIN-
Rail Mount Hub w/ Gigabit Ethernet & DB9 Serial FTDI Chipset! Please read the
manual in detail fi rst before you begin using this hub. The specifi cations are subject to
change without notice.
Desktop or Notebook Computer with an Available USB Type-A or USB Type-C Port
Windows 11 (64-bit), 10 (32/64-bit), 8 (32/64-bit), 7 (32/64-bit)
Mac OSX Lowest or Latest Versions
Industrial 2-Port USB & Serial 3.2 Gen 1 Hub
User Manual
Power Adapter with DC Barrel Connector
USB Type-A to Type-B Cable
DIN-Rail & Wall Mounting Kit
3-Pin Terminal Block
Screw Package
Driver Disc

2
gearmo.com/support
2
gearmo.com/support
Hub Layout
Installation
1. Power
- The USB 3.2 Gen 1 Hub requires a 9~48V DC external power source to work.
- Power up the USB Hub through either the Included DC Power Jack Adapter or 3-Pin
Terminal Block.
2. 3-Pin Terminal Block
- Plug the included terminal block to the hub’s terminal block connector.
3. Hardware
- Mount your hub on the Wall, Surface or Din Rail, if needed.
Downstream Ports
USB Type-A
Downstream Port
RS-232 DB9
DC Power Jack
Upstream Port
USB Type-B
Ethernet Port
RJ-45
Terminal Block

3
gearmo.com/support
DIN Rail Mounting
Use the included screws to install the DIN Rail Clip to the hub.
Insert the top of the DIN Rail Clip onto the DIN Rail Track, then gently push the bottom
of the hub to secure it to the DIN Rail Track.

4
gearmo.com/support
4
gearmo.com/support
Surface / Wall Mounting
Use the included screws to affi x the surface mounting fl anges to the hub. Use surface
mounting screws attach hub to the wall or smooth surface (surface mounting screws not
included).

5
gearmo.com/support
Specifi cations
Support all USB 1.1 to 3.2 Gen 1 compatible peripheral device data transfer upto 5Gbps
Support Ethernet 10/100/1000 Mbps
Single RS232
9-48V DC input
Support LED indicator
Supported OS Systems Windows 11/10/8/7 and Mac OS
Support USB 3.0 plug and play
15KV ESD surge protection
Operating temperature 0-50C

6
gearmo.com/support
Windows Installation
RS-232
1. Put the driver CD in the CD ROM driver
2. Open the path: “CD ROM-driver\FTDI drivers\Setup.exe”, afterwards click next.
3. Click fi nish to complete the installation.
4. Open device manager to make sure that the driver was installed successfully.
5. You can now start to use the device.
Ethernet Port
1. Put the driver CD in the CD ROM driver
2. Open the path: “CD ROM-driver\realtek drivers\Setup.exe”, afterwards click next.
3. Click fi nish to complete the installation
4. Open device manager to make sure that the driver was installed successfully.
5. You can now start to use the device.