Gecko in.xm2 Technical manual

2- Connect the main power
1- Connect all outputs & keypads
Fuses
Power box display and buttons
Main power entry connection
Main power cable input entry Mounting feet
Installation brackets
OUT1
L1 - Light connector General I/O connector
(IR receiver)
C - Main and aux. keypad connectors
CO - Communication link
OUT8 - Connector for direct 120/240 vac
5 Amp output
OUT7
OUT5
OUT6
OUT2 OUT3 OUT4
Don't forget that the voltage is determined by the cable used (120 or 240V cable)!
For 240 VAC (*3 wires)
* If connected to a 3 wire system (without neutral),
all 120 VAC components will not work.
For 240 VAC (4 wires)
Correct wiring of the electrical service box, GFCI,
and pack terminal block is essential.
Call an electrician if necessary.
RH - Output connectors for in.therm™
remote heating system (240 vac)
4- Select breaker current
Make sure all accessories are linked to the bonding connector and connected to
pack. Make sure the spa pack door is closed. Turn on the breaker.
Bonding lug
3- Select spa configuration (see chart next page)
First, the led display will show "LL" and "01" continuously.
Press Change button to choose the appropriate
configuration for your spa.
Press Select button to confirm.
(The pack will now reset and reboot)
Note: To re-enter the configuration selection menu the press Select
button and hold for 5 seconds.
Press Change button to choose the breaker current value.
Press Select button to confirm.
(The pack will now reset and reboot)
Note: Br values display by the pack correspond
to 80% of the maximum amperage
capacity of the GFCI.
GFCI Br
60 Amp 48 Amp
50 Amp 40 Amp
40 Amp 32 Amp
25 Amp 20 Amp
20 Amp 16 Amp
Selecting breaker current (Br)
For more information, see our website: www.geckoalliance.com
For more information, see our website: www.geckoalliance.com
Quick Start Card
in.xm2™North American version

Note: This low level configuration table is valid for the sofware #181 revision 3. This information is
displayed on top side keypad at spa pack power-up. Software number is displayed first (ex: ,
, ), followed by revision (ex: ). For in.k600™ (menu-driven interface), you will find
the information in Info sub-menu located in Options menu.
8
Config #. Pump 1 Pump 2 Pump 3 Pump 4 Pump 5 BL TV lifter Sanitation Circ. Pump Heat with
P1 or CP?
Filtration/Ozone with
P1 or CP?
12sp ________ P1 P1
22sp _______xCP CP
32sp 2sp _______ P1 P1
42sp 2sp ______xCP CP
52sp 2sp ___x___ P1 P1
62sp 2sp ___x_ _ xCP CP
72sp 2sp x______ P1 P1
82sp 2sp x_____xCP CP
92sp 2sp x_ _ x___ P1 P1
10 2sp 2sp x_ _ x_ _ xCP CP
11 2sp 2sp x______ P1 P1
12 2sp ____x___ P1 P1
13 2sp ____x_ _ xCP CP
14 1sp 1sp ______xCP CP
15 1sp 1sp ___x_ _ xCP CP
16 1sp 2sp x_____xCP CP
17 1sp 2sp x_ _ x_ _ xCP CP
18 2sp 1sp _______ P1 P1
19 2sp 1sp ___x___ P1 P1
20 2sp 2sp x______ P1 P1
21 2sp 1sp x_ _ x___ P1 P1
22 2sp 1sp ______xCP CP
23 2sp 1sp ___x_ _ xCP CP
24 2sp 2sp x_____xCP CP
25 2sp 2sp x_ _ x_ _ xCP CP
26 1sp 2sp x_____xCP CP
27 1sp 2sp x x ____xCP CP
28 1sp 2sp xxx___xCP CP
29 VSP 2sp VSP ___x x _P1 P1
30 VSP 2sp ____x x _P1 P1
31 VSP _VSP ___x x _P1 P1
9919-101177-D Rev. 07-2016
© Groupe Gecko Alliance Inc., 2016
All trademarks or registered trademarks are the property of their respective owners.
www.geckoalliance.com
Configuration selection chart
Software #181, rev. 3.00
Glossary
P1 Pump 1
CP Circulation Pump
VSP VSP Pump
1sp 1 speed pump
2sp 2 speeds pump
X Installed For complete TechBook or more information, see our website: www.geckoalliance.com
3.00