Gefen EXT-DIGAUD-141 User manual

www.gefen.com
®
Digital Audio
Extender
EXT-DIGAUD-141
User Manual

ASKING FOR ASSISTANCE
Rev A3
Technical Support:
Telephone [phone]
[phone]
Fax [phone]
Technical Support Hours:
8:00 AM to 5:00 PM Monday thru Friday PST
Write To:
Gefen, LLC
c/o Customer Service
20600 Nordhoff St
Chatsworth, CA 91311
www.gefen.com
[email protected]
Notice
Gefen, LLC reserves the right to make changes in the hardware, packaging, and
any accompanying documentation without prior written notice.
Digital Audio Extender is a trademark of Gefen, LLC
© 2012 Gefen, LLC. All rights reserved.
All trademarks are the property of their respective owners

TABLE OF CONTENTS
Introduction
Box Contents and Operation Notes
Connecting the Digital Audio Extender
Panel Layouts
Link Cable Wiring Diagram
Specications
Warranty
1
2
3
4
5
6
7

Congratulations on your purchase of the Digital Audio Extender. Your complete
satisfaction is very important to us.
Gefen
Gefen delivers innovative and progressive computer and electronics add-
on solutions that harness integration, extension, distribution, and conversion
technologies. Gefen’s reliable, plug-and-play products supplement cross-platform
computer systems, professional audio/video environments, and HDTV systems
of all sizes with hard-working solutions that are easy to implement and simple to
operate.
The Gefen Digital Audio Extender
Place your digital audio components anywhere you want with Gefen’s Digital
Audio Extender. It supports either S/PDIF or TOSLINK digital audio signals, which
are commonly used to transmit stereo and multichannel digital audio like Dolby®
Digital and DTS®. The Digital Audio Extender uses a Sender and Receiver system
connected by a CAT-5e cable to extend the digital audio up to a 330 feet (100
meters).
How It Works
The Digital Audio Extender’s Sender unit connects to the audio source
component. The Digital Audio Extender’s Receiver unit connects to the extended
audio component (up to 330 feet away). One CAT-5e cable connects the Sender to
the Receiver unit.
INTRODUCTION
1

The Digital Audio Extender system consists of:
(1) Digital Audio Extender - Sender Unit
(1) Digital Audio Extender - Receiver Unit
(1) 6 ft. TOSLINK Cable
(1) 5V DC power supply
(1) Quick-Start Guide
BOX CONTENTS
READ THESE NOTES BEFORE INSTALLING
OR OPERATING THE DIGITAL AUDIO EXTENDER SYSTEM
Industry standard Category-5 (CAT-5 or CAT-5e) cables are used to link the Digital
Audio Extender Sender and Receiver units together.
The Digital Audio Extender units are housed in metal boxes for RF shielding.
The Digital Audio Extender uses any single CAT-5/CAT-5e/CAT-6a cable of no
more than 330 feet (100 meters) in length.
OPERATION NOTES
2
Figure 1. Top photo of the Digital Audio Extender Sender and
Receiver units showing the positions and markings of connectors.

CONNECTING THE DIGITAL AUDIO EXTENDER
How to Connect the Digital Audio Extender System:
1- Connect your digital audio source’s outputs to the Sender unit’s digital input using
either the TOSLINK or the S/PDIF input. Please see “Panel Layout” on page 4
for a list of connectors on the units.
2- Connect the Sender and Receiver units to one another on their RJ45 link
connector jacks using a single CAT-5 cable.
3- Connect the digital output of the Receiver unit to the digital input of the amplier/
speaker system using either the TOSLINK or the S/PDIF connection. The digital
audio will be present on both the TOSLINK and S/PDIF output regardless of which
digital input is used on the Sender unit.
4- Power on your audio sources and audio playback system. Plug the included
5 Volt DC power supply into the Sender unit. Observe that the red LED on the
Receiver unit lights up. If it does not, examine all connections carefully and try
again. Upon successful powered connection of the Sender and Receiver units, you
will hear pristine digital audio on your digital audio playback equipment connected to
the Receiver unit.
Please refer to the next page (page 4) for a detailed panel layout showing
all connectors on the sender and receiver units.
3

PANEL LAYOUTS
4
Sender (CAT5 link side)Receiver (CAT5 link side)
1 2 3 4
Receiver (output side) Sender (input side)
5 6 78
Connections -- Digital Audio Extender Sender & Receiver units
1. RJ45 Jack -- CAT5 cable connection from Sender unit plugs in here
2. Power LED on Receiver -- indicates successful hookup between units
3. 5V DC socket -- Connect the external power supply here (on Sender)
4. RJ45 Jack -- CAT5 cable connection from Receiver unit plugs in here
5. S/PDIF Jack -- Connect digital audio cable here to feed amp / speakers
6. TOSLINK Jack -- Connect digital audio cable here to feed amp / speakers
7. S/PDIF Jack -- Connect digital audio cable here from source to Sender
8. TOSLINK Jack -- Connect digital audio cable here from source to Sender

LINK CABLE WIRING DIAGRAM
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
RJ-45 Jack RJ-45 Jack
2 3 4 5
6
7 8 1
2
3 4 5
6
7
8 1
1818
5

Input/Output .................................................................................... S/PDIF, TOSLINK
Link Connector ................................................................................... RJ-45 Shielded
Power Supply ....................................................................................................5V DC
Power Consumption: .......................................................5W (max) per power supply.
Dimensions (W x H x D)............................ 3.8” x 1.2” x 1.4” (96mm x 30mm x 35mm)
Shipping Weight .................................................................................... 5 lbs. (2.3 kg)
SPECIFICATIONS
6