Gefen EXT-DP-CP-2FO User manual

Audio
Embedder
3GSDI
Release A1
User Manual
EXT-DP-CP-2FO
DisplayPort Extender
over 2 LC Fibers

DisplayPort Extender over 2 LC Fibers
Important Safety Instructions
ii
GENERAL SAFETY INFORMATION
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this product near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install or place this product near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. To reduce the risk of electric shock and/or damage to this product, never handle or
touch this unit or power cord if your hands are wet or damp. Do not expose this
product to rain or moisture.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
15. Batteries that may be included with this product and/or accessories should never be
exposed to open ame or excessive heat. Always dispose of used batteries
according to the instructions.

Warranty Information
Gefen warrants the equipment it manufactures to be free from defects in material and
workmanship.
If equipment fails because of such defects and Gefen is notied within two (2) years from
the date of shipment, Gefen will, at its option, repair or replace the equipment, provided
that the equipment has not been subjected to mechanical, electrical, or other abuse or
modications. Equipment that fails under conditions other than those covered will be
repaired at the current price of parts and labor in effect at the time of repair. Such repairs
are warranted for ninety (90) days from the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including without
limitation, any implied warranty or merchantability or tness for any particular purpose, all of
which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2. Customers outside the US are responsible for shipping charges to and from Gefen.
3. Copper cables are limited to a 30 day warranty and cables must be in their original
condition.
The information in this manual has been carefully checked and is believed to be accurate.
However, Gefen assumes no responsibility for any inaccuracies that may be contained
in this manual. In no event will Gefen be liable for direct, indirect, special, incidental, or
consequential damages resulting from any defect or omission in this manual, even if
advised of the possibility of such damages. The technical information contained herein
regarding the features and specications is subject to change without notice.
For the latest warranty coverage information, refer to the Warranty and Return Policy under
the Support section of the Gefen Web site at www.gefen.com.
PRODUCT REGISTRATION
Please register your product online by visiting the Register Product page under the
Support section of the Gefen Web site.
iii
DisplayPort Extender over 2 LC Fibers

iv
Gefen, LLC
c/o Customer Service
20600 Nordhoff St.
Chatsworth, CA 91311
Telephone: [phone]
[phone]
Fax: [phone]
Email: [email protected]
Visit us on the Web: www.gefen.com
Technical Support Hours: 8:00 AM to 5:00 PM Monday - Friday, Pacic Time
DisplayPort Extender over 2 LC Fibers
is a trademark of Gefen, LLC.
Important Notice
Gefen, LLC reserves the right to make changes in the hardware, packaging, and any
accompanying documentation without prior written notice.
© 2013 Gefen, LLC. All Rights Reserved.
All trademarks are the property of their respective owners.
Contacting Gefen Technical Support
iv
DisplayPort Extender over 2 LC Fibers

vv
Operating Notes
• Fiber optic cables must be treated carefully when connectors are exposed. They are
susceptible to dust which can cause pixel loss.
• The DisplayPort Extender over 2 LC Fibers works for all DisplayPort displays and
supports resolution up to WQXGA (2560 x 1600 @ 60Hz).
• Extension distance will depend upon the type of ber optic cable that is used:
► Up to 1000 feet (300 meters) when using LC terminated OM2/OM3 ber
► Up to 500 feet (150 meters) when using LC terminated OM1 ber
• HDCP and DPCP compliant
DisplayPort Extender over 2 LC Fibers

vi
Features
• Extends DisplayPort up to 1000 feet (300 meters) over 2 strands of 50/125µm
multi-mode (OM2/OM3) LC-terminated ber optic cable
• Extends DisplayPort up to 500 feet (150 meters) over 2 strands of 62.5/125µm
multi-mode (OM1) LC-terminated ber optic cable
• Supports resolutions up to WQXGA (2560 x 1600 @ 60Hz)
• Compliant with DisplayPort 1.1a standard
• Supports Dual-Mode DisplayPort (DP++)
• Supports auxiliary/l²C channel over ber
• Fiber optic transmission eliminates susceptibility to electromagnetic interference (EMI)
• HDCP and DPCP-compliant
• Compact Sender and Receiver modules and female DisplayPort connectors provide
clean, easy installation
• FCC and CE compliant for RFI (radio frequency interference) and EMI
(electromagnetic immunity)
Packing List
The DisplayPort Extender over 2 LC Fibers ships with the items listed below. If any of these
items are not present in your box when you rst open it, immediately contact your dealer or
Gefen.
• (1) DisplayPort Extender over 2 LC Fibers (Sender module)
• (1) DisplayPort Extender over 2 LC Fibers (Receiver module)
• (2) DisplayPort cables (M-M)
• (2) USB to DisplayPort cables (M-M)
• (2) 5V / 1A DC power supply
• (1) Quick-Start Guide
Features and Packing List
DisplayPort Extender over 2 LC Fibers

3GSDI Audio Embedder
Table of Contents
viii
DisplayPort Extender over 2 LC Fibers
01 Getting Started
Module Layout....................................................................................................... 2
Sender Module.............................................................................................. 2
Receiver Module ........................................................................................... 4
Installation ............................................................................................................. 6
Connecting the DisplayPort Extender over 2 LC Fibers................................ 6
Sample Wiring Diagram ................................................................................ 6
02 Appendix
Specications ...................................................................................................... 10

DisplayPort Extender
over 2 LC Fibers
01 Getting Started
Module Layout....................................................................................................... 2
Sender / Receiver Module............................................................................. 2
Installation ............................................................................................................. 4
Connecting the DisplayPort Extender over 2 LC Fibers................................ 4
Sample Wiring Diagram ................................................................................ 6

page | 2
Sender Module
Top
Bottom
Getting Started
Module Layout
2
1
3 4
Back Front
5

page | 3
ID Name Description
1 Power indicator This LED indicates the power status of
the Sender module. See Connecting the
DisplayPort Extender over 2 LC Fibers for
more information.
2 Power receptacle Connect the included 5V DC power supply
to this power receptacle.
3 DisplayPort connector Use a DisplayPort cable to connect the
source to this connector.
4 LC connectors Connect two strands of LC-terminated
ber optic cable from these ports to the
associated ports on the Receiver module.
See Connecting the DisplayPort Extender
over 2 LC Fibers for important information
on connecting ber optic cables.
5Status indicator This LED indicates the connection status of
the Sender module. See Connecting the
DisplayPort Extender over 2 LC Fibers for
more information on connecting ber optic
cables.
Getting Started
Module Layout

page | 4
Receiver Module
Top
Bottom
Getting Started
Module Layout
2
1
3 4
Back Front
5

page | 5
Getting Started
Module Layout
ID Name Description
1 Power indicator This LED indicates the power status of the
Receiver module. See Connecting the
DisplayPort Extender over 2 LC Fibers for
more information.
2 Power receptacle Connect the included 5V DC power supply
to this power receptacle.
3 DisplayPort connector Use a DisplayPort cable to connect the
display to this connector.
4 LC connectors Connect two strands of LC-terminated
ber optic cable from these ports to the
associated ports on the Sender module.
See Connecting the DisplayPort Extender
over 2 LC Fibers for important information
on connecting ber optic cables.
5Status indicator This LED indicates the connection status of
the Receiver module. See Connecting the
DisplayPort Extender over 2 LC Fibers for
more information on connecting ber optic
cables.

Connecting the DisplayPort Extender over 2 LC Fibers
1. Connect a DisplayPort cable from the source to the DisplayPort connector on the
Sender module.
2. Connect a DisplayPort cable from the display to the DisplayPort connector on the
Receiver module.
3. Connect 2 strands of LC-terminated multimode ber optic cable from the Sender
module to the Receiver module. See the Table 2.1 on the next page for distance
information based on the type of ber optic cable.
4. Connect the included 5V DC power supplies to the power receptacles on both the
Sender and Receiver module. The LED on the top of both the Sender and Receiver
module will ash slowly 3 times, then ash quickly as long as power is applied.
See Table 2.2 on the next page for details on LED status.
Sample Wiring Diagram
page | 6
Getting Started
Installation
IMPORTANT: Each ber optic port is identied by the letter A or B.
Make sure that the ber optic cables between the Sender and
Receiver module are connected to the proper port, as shown below.
Computer
HD Display
Receiver
Sender
EXT-DP-CP-2FO
FIBER OPTIC CABLE
DISPLAYPORT CABLE

page | 7
Getting Started
Installation
Table 2.1 - Fiber optic cable distance
Maximum distance 500 feet (150 meters) 1000 feet (300 meters)
Category OM1 OM2 / OM3
Core size / cladding
diameter
62.5µm / 125µm 50µm / 125µm
Table 2.2 - LED indicator status
LED Status Conditions
Top Off • The Sender module is not powered.
• The Receiver module is not powered.
Flashes 3
times and
turns off
• The Sender and Receiver module are
powered but are not connected using
ber optic cable.
Flashing • The Sender and Receiver modules
are powered and connected to one
another using LC-terminated ber
optic cables.
Bottom Solid blue • The display is connected to the
Receiver module.
Off • The display has been disconnected
from the Receiver module.

DisplayPort Extender
over 2 LC Fibers
02 Appendix
Specications ...................................................................................................... 10

page | 10
Appendix
Specications
Supported Formats
Resolution (max.) • WQUXGA (2560 x 1600 @ 60Hz)
Electrical
Video bandwidth • 10.8 Gb/s (2.7 Gb/s per lane, 4 lanes)
Connectors
Video Input Connector (Sender) • 1 x DisplayPort 20-pin, female
Video Output Connector (Receiver) • 1 x DisplayPort 20-pin, female
Link Connector (Sender / Receiver) • 2 x LC-type
Operational
Power Supply (Sender / Receiver) • 5V DC
Power Consumption (Sender / Receiver) • 2.1W (max.) each
Optical Power Budget • 9.4 dB
Operating Temperature • +32 to +122 °F (0 to +50 °C)
Storage Temperature • -22 to +158 °F (-30 to +70 °C)
Operating Humidity • 10 to 85% RH (non-condensing)
Storage Humidity • 5 to 90% RH (non-condensing)
Physical
Dimensions (W x H x D) • 1.4” x 0.6” x 2.8”
(35mm x 16mm x 72mm)
Unit Weight (each) • 0.1 lb (0.05 kg)