Gefen DVI-444DL User manual

www.gefen.com
f
4x4 DVI Dual Link
Matrix
EXT-DVI-444DL
User Manual

Technical Support:
Telephone [phone]
[phone]
Fax [phone]
Technical Support Hours:
8:00 AM to 5:00 PM Monday thru Friday.
Write To:
Gefen Inc.
c/o Customer Service
20600 Nordhoff St
Chatsworth, CA 91311
www.gefen.com
[email protected]
Notice
Gefen Inc. reserves the right to make changes in the hardware, packaging and
any accompanying documentation without prior written notice.
4x4 DVI DL Matrix is a trademark of Gefen Inc.
© 2008 Gefen Inc., All Rights Reserved
All trademarks are the property of their respective companies
ASKING FOR ASSISTANCE

CONTENTS
1 Introduction
2 Operation Notes
3 Features
4 Panel Layout
5 Panel Descriptions
6 Connecting And Operating The 4x4 DVI DL Matrix
7 Configuring The 4x4 DVI DL Matrix
9 RS-232 Serial Control Interface
10 Rack Mount Installation
11 Specifications
12 Warranty

1
Congratulations on your purchase of the 4x4 DVI DL Matrix. Your complete
satisfaction is very important to us.
Gefen
Gefen delivers innovative, progressive computer and electronics add-on solutions
that harness integration, extension, distribution and conversion technologies.
Gefen’s reliable, plug-and-play products supplement cross-platform computer
systems, professional audio/video environments and HDTV systems of all sizes
with hard-working solutions that are easy to implement and simple to operate.
The Gefen 4x4 DVI DL Matrix
Easily combine any four cross-platform Dual Link DVI video display outputs and
four Dual Link DVI digital displays without networking. Our 4x4 DVI Dual Link
Matrix provides a simple, reliable and highly effective method of creating multiple
Dual Link DVI display consoles, with each console capable of accessing any one
of the Dual Link DVI video sources at any time by remote control. You also have
the option of setting up the four displays locally or extending them with a Gefen
extender.
How It Works
The 4x4 DVI Dual Link Matrix has four Dual Link DVI inputs and four Dual Link
DVI outputs. You simply connect your four Dual Link DVI video sources to the
Switcher’s inputs, then connect your four Dual Link DVI displays to the Switcher’s
outputs.
INTRODUCTION

READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE 4X4 DVI DL MATRIX
4x4 DVI DL Matrix does not have any scaling functionality. All of the attached• monitors must be able to display the attached sources’ resolution. For
maximum compatibility it is recommended that only one compatible/common
resolution for all displays be used by all sources.
2
OPERATION NOTES

3
Features
Increases your productivity by letting you view any four Dual Link DVI video• sources on any four Dual Link DVI displays
Maintains highest resolution digital video with no loss of quality•
Discrete IR Remote (included)•
Supports video resolutions up to 3840x2400•
Supports DDWG standards for DVI monitors•
Includes rack ears•
Package Includes
(1) 4x4 DVI Dual Link Matrix
(1) RMT-16IR
(1) 5V DC Power Supply
(4) 6 Foot Dual Link DVI cables
(1) Set Of Rack Ears
(1) User’s Manual
FEATURES

4
Front Panel
Back Panel
PANEL LAYOUT
123 45
910111213141516
8
17
67

5
PANEL DESCRIPTIONS
Display 1 Selected Source LED1 The array of 4 LED’s correspond to the 4 source inputs on the back panel of the 4x4 DVI DL
Matrix. The currently selected source being displayed on DVI Output 1 will be indicated by an
active LED.
Display 2 Selected Source LED2 The array of 4 LED’s correspond to the 4 source inputs on the back panel of the 4x4 DVI DL
Matrix. The currently selected source being displayed on DVI Output 2 will be indicated by an
active LED.
Display 3 Selected Source LED3 The array of 4 LED’s correspond to the 4 source inputs on the back panel of the 4x4 DVI DL
Matrix. The currently selected source being displayed on DVI Output 3 will be indicated by an
active LED.
Display 4 Selected Source LED4 The array of 4 LED’s correspond to the 4 source inputs on the back panel of the 4x4 DVI DL
Matrix. The currently selected source being displayed on DVI Output 4 will be indicated by an
active LED.
IR Receiver5 This IR receiver will receive commands from the included RMT-16-IR remote control.
IR Extension Port6 Connect an optional IR extension (part# EXT-RMT-EXTIR) to this port.
Power LED Indicator7 This LED will become active once the included 5V DC power adapter is properly connected.
RS-232 Serial Control Interface8 Use the commands on page 10 to control the 4x4 DVI DL Matrix using the RS-232 interface.
DVI Input 19 Connect a DVI DL source to this input.
DVI Input 210 Connect a DVI DL source to this input.
DVI Input 311 Connect a DVI DL source to this input.
DVI Input 412 Connect a DVI DL source to this input.
DVI Output 113 Connect a DVI DL display to this port.
DVI Output 214 Connect a DVI DL display to this port.
DVI Output 315 Connect a DVI DL display to this port.
DVI Output 416 Connect a DVI DL display to this port.
Locking 5V DC Power Adapter Input17 Connect the included 5V DC power adapter to this port.

6
How to Connect the 4x4 DVI DL Matrix
Connect up to 4 DVI DL sources to the 4x4 DVI DL Matrix input ports using1. the supplied DVI DL cables.
Connect up to 4 displays to the 4x4 DVI DL Matrix output ports using user2. supplied DVI DL cables.
Connect the supplied 5V DC power supply to the 4x4 DVI DL Matrix.3.
Power on the displays.4.
Power on each source individually ensuring that a display is pointing to it5. while the power on procedure completes.
NOTE: It is extremely important to ensure that when each source is being
powered on it has a display pointing to it. Most sources require (a definite
requirement if computers are being used) a display to be attached to
receive EDID (display information) and to begin operation. If a source
does not have a display that is pointing to it, a video image may fail to be
displayed. It is recommended that each source be powered on and verified
that it is outputting video before moving on to power the next source.
CONNECTING AND OPERATING THE 4X4 DVI DL MATRIX

7
Remote Channel 1:
Default
1 2
Remote Channel 2:
1 2
Remote Channel 3:
1 2
Remote Channel 4:
1 2
Remote Channel 1:
Default
1 2
Remote Channel 2:
1 2
Remote Channel 3:
1 2
Remote Channel 4:
1 2
RMT-16-IR REMOTE CONTROL 4x4 DVI DL Matrix
12345678
OFF
ON
The 4x4 DVI DL Matrix has a bank of 8 configuration DIP SWITCHES. These
switches are located underneath the unit. Peeling back the black metallic sticker
on the bottom of the 4x4 DVI DL Matrix will reveal the Dip Switch bank. These
service switches are used for a number of configuration options. By default, all
Dip Switches are in the OFF position. Each setting is outlined below.
IR Remote Channel ConfigurationSwitch 1
IR Remote Channel ConfigurationSwitch 2
Automatic Link Selection \ Dual Link Only ModeSwitch 3
Not UsedSwitch 4
Pre-Empahsis For Display Output 1Switch 5
Pre-Empahsis For Display Output 2Switch 6
Pre-Empahsis For Display Output 3Switch 7
Pre-Empahsis For Display Output 4Switch 8
IR REMOTE CHANNEL CONFIGURATION
Dip Switches 1 and 2 relate to the IR remote control channel that is used by the 4x4
DVI DL Matrix and RMT-16-IR remote control. Dip Switch 1 and 2 on the 4x4
DVI DL Matrix must match Dip Switch 1 and 2 on the RMT-16-IR remote control.
Please view the table below to set the channel on 4x4 DVI DL Matrix and IR
remote control. The remote channel for the RMT-16-IR is located underneath it’s
battery cover.
CONFIGURING THE 4X4 DVI DL MATRIX

8
AUTOMATIC LINK SELECTION / DUAL LINK ONLY MODE
The 4x4 DVI DL Matrix has the ability to run both Single Link and Dual Link DVI
sources. There is a feature that will either automatically select the link mode, or lock
the unit in Dual Link mode. By default, Dip Switch 3 is in the OFF position (Automatic
Link Selection). Turning Dip Switch 3 to the ON position will lock the unit in Dual Link
mode and will only allow Dual Link signals to pass properly.
PRE-EMPHASIS
Pre-Emphasis is used to help extend a signal travel over a distance of cable. When
a DVI cable connected to a display is over a long cable, it is recommended that
Pre-Emphasis be enabled. Pre-emphasis is enabled by default on all display
outputs. For short cables, disable pre-emphasis on each output by turing it’s
corresponding Dip Switch to the ON position. If any type of extension device is
used pre-emphasis must be disabled for proper operation.
CONFIGURING THE 4X4 DVI DL MATRIX

9
RS-232 SERIAL CONTROL INTERFACE
Binary Table
ASCII Corresponding
RMT16-IR
Button
Binary ASCII Corresponding
RMT16-IR
Button
Binary
1 1 0011 0001 9 9 0011 1001
2 2 0011 0010 a 10 0110 0001
3 3 0011 0011 b 11 0110 0010
4 4 0011 0100 c 12 0110 0011
5 5 0011 0101 d 13 0110 0100
6 6 0011 0110 e 14 0110 0101
7 7 0011 0111 f 15 0110 0110
8 8 0011 1000 g 16 0110 0111
RS232 Settings
Bits per second ................................................................................................. 19200
Data bits .................................................................................................................... 8
Parity .................................................................................................................. None
Stop bits .....................................................................................................................1
Flow Control ....................................................................................................... None
12345
6789
12345
6789
Only Pins 2 (RX), 3 (TX), and 5 (Ground) are used on the RS-232 serial interface

10
Rear of unit
Front of unit
Rack mount ears are provided for installation of this unit into a 1U rack mount
space.
Locate the side screws on the unit.1. Remove the front 2 screws that are located closest to the front of the unit.2. Using the removed screws, screw the rack mounting bracket into the unit.3. Repeat the procedure on the opposite side of the unit.4.
1
2
3
4
RACK MOUNT INSTALLATION

11
Video Amplifier Bandwidth ................................................................. 2 x 165 MHz
Input Video Signal .............................................................................. 1.2 Volts p-p
Input DDC Signal ......................................................................... 5 Volts p-p (TTL)
Dual Link Maximum Video Range ........................................................ 3840x2400
DVI Connector .................................................... DVI-I 29 pin female (digital only)
Power Supply .............................................................................................. 5V DC
Power Consumption ....................................................................... 20 Watts (max)
Dimensions ..................................................................... 17”W x 1.75”H x 5.875”D
Rack Mountable ............................................................................ 1U Rack Space
Shipping Weight .......................................................................................... 10 Lbs
SPECIFICATIONS