GeneralAire Elite Stream User manual

Elite Steam
Residential Steam Humidifiers
User manual
Revision 3.4

Warning
If present, remove the following items:
LATCH THE CYLINDER CLAMP
REMOVE BEFORE INSTALLING
REMOVE BEFORE INSTALLING
REMOVE BEFORE INSTALLING
REMOVE BEFORE INSTALLING
REMOVE BEFORE INSTALLING

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
3
IMPORTANT WARNINGS
BEFORE INSTALLING OR HANDLING THE HUMIDIFIER PLEASE CAREFULLY READ AND FOLLOW THE INSTRUCTIONS
AND SAFETY STANDARDS DESCRIBED IN THIS MANUAL AND ON THE LABELS ATTACHED TO THE Elite Steam.
CAUTION: ALWAYS DISCONNECT THE MAIN POWER BEFORE OPENING OR SERVICING THE HUMIDIFIER!
Elite Steam produces non-pressurized steam by means of electrodes immersed in the water contained in the plastic steam
generator cylinder. Electric current passes through the water between the electrodes, heating the water into steam, which is then
used to humidify the air.
The quality of the water used affects the operation of this unit, so the Elite Steam may be supplied with untreated water, as long as
this is drinkable and not softened or demineralized. The water converted into steam is automatically replaced through an electric fill
valve. Periodically, based on the water quality, the unit will also drain some water to dilute the build-up of minerals in the steam
generator. In cases of high water mineral content, an activated carbon filter is series with a particulate filter, no more than 5 microns
is suggested.
This humidifier has been designed exclusively to directly humidify rooms or ducts, using a distribution system. The installation, use
and maintenance operations must be carried out according to the instructions contained in this manual and on the labels applied
internally and externally.
IMPORTANT: BEFORE beginning installation:
Check for shipping damage to cartons. Mark the shipping waybill accordingly.
Open cartons and check for any hidden damage. Mark the shipping waybill accordingly.
Check packing slip to ensure all items have been received. Notify GENERAL FILTERS, INC. of any shortages or damaged
parts. You must notify General Filters, Inc. within 5 working days of any shortages.
CAUTION: ELECTRIC SHOCK HAZARD! The humidifier has components under power inside!
CAUTION: SCALDING HAZARD! The humidifier has hot parts (100°C/ 212°F)
WARNING: Install the humidifier out of the reach of children.
The humidifier must be installed in accordance with all local and national standards.
All service and/or maintenance operations must be performed by qualified personnel who are aware of the necessary
precautions and are capable of performing the operations correctly.
Disconnect the humidifier from the main power supply before accessing any internal parts.
The conditions of the environment and the power supply voltage must comply with the specified values listed on the data
label in the humidifier.
All other uses and modifications made to the humidifier that are not authorized by the manufacturer are considered
incorrect, and the manufacturer assumes no liability for the consequences of any such unauthorized use.
Please note that the humidifier contains powered electrical devices and hot surfaces.
The humidifier is made of metallic and plastic parts. All parts must be disposed of according to the local and national
standards for waste disposal.
WARNING: Your humidifier requires water to operate. Do NOT mount it above materials or machinery that could be
damaged if a leak occurs. General Filters, Inc. assumes no responsibility for consequential or inconsequential damage as
a result of any leaks.
Disposal of the parts of the humidifier: the humidifier is made up of metallic and plastic parts. All parts must be disposed
of according to the local standards on waste disposal.
We wish to save you time and money!
We can assure you that the thorough
reading of this manual will guarantee
correct installation and safe use of the
product described.

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
4

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
5
CONTENTS
1. How The Elite Steam Works 6
1.1 Basic Operation 6
1.2 Cylinder Life 7
1.3 Calculating Humidity Load 7
2. Models 8
3. INSTALLATION 9
3.1 Positioning 9
3.2 Mounting 9
3.3 Plumbing 11
3.4 Steam distribution 12
3.5 Power wiring 15
3.6 Control wiring 15
3.7 Wiring Connections 17
4. START-UP 18
4.1 Startup Checklist 18
4.2 The Elite Steam Controller 18
4.3 Starting Elite Steam 18
4.4 Starting with a new cylinder 18
5. OPERATING ELITE STEAM 19
5.1 Displaying Information 19
5.2 Changing The Maximum Production 19
5.3 Activating Manual Drain 19
5.4 Resetting the hour counter 19
5.5 Using the E2 Humidistat 20
5.6 Alarms 20
6. TROUBLE SHOOTING 21
7. Maintenance 22
7.1 Periodic checks 22
7.2 Cylinder maintenance 22
7.3 Replacement Parts 23
8. TECHNICAL SPECIFICATIONS 24
9. LIMITED WARRANTY 25

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
6
1. HOW THE ELITE STEAM WORKS
1.1 Basic Operation
Elite Steam is an electrode humidifier. It produces steam for humidification by
passing electric current through the water between metal electrodes in the
plastic steam generator cylinder. There are no heating elements. Steam output
is directly proportional to the conductivity of the water, and the amount of
electrode immersed in the water.
On a call for humidity, the Elite Steam controller will open the water fill valve (1)
and allow water to enter the cylinder. A flow restrictor (4) prevents the unit from
filling too quickly or with too much pressure. The water flows up the fill tube (2)
and into the fill cup (3).Water then flows over the dam in the fill cup (3), which
creates a 1” air gap to prevent backflow of contaminated water into the feed
lines, and through the fill tube (6) and into the bottom of the steam cylinder (5).
Any backflow or overflow of water travels through the overflow hose (13) to the
drain.
As the water fills the cylinder, it will reach the electrodes (7) and current will
begin to flow. As the water continues to fill the cylinder, the current will
increase, and this is monitored by an amperage transformer connected to one of the power wires and located on the
electronic controller. When the desired current is reached, the fill valve will close (1) and the water will then begin to warm
and produce steam. If the water reaches the cylinder full probes (9) or if current rises too much, the drain pump (11) will be
activated to drain away some water and reduce the current flow to acceptable levels. Note that, any time the drain pump is
activated, the tempering valve (10) will be opened for tempering the hot drained water down to 140 degrees F / 60 degrees C
in accordance to local and national standards.
Periodically, based on the incoming water conductivity, the unit will run drain pump (11) and drain some water to reduce the
mineral concentration. Every 120 hours the unit automatically drains to remove mineral sediment on the bottom of the
cylinder. A strainer (12) in the cylinder helps to prevent mineral debris from jamming the drain pump (11).
In case Elite Steam remains powered but idle, i.e. without producing steam, for more than 72 hours (3 days), the cylinder will
be emptied to not have stagnant water inside.
If there is no water in the cylinder, there will be no current flow and no steam production. The electrodes do not burn out, but
they will eventually become completely coated with mineral and the cylinder will then need to be replaced. Cleaning cylinders
may cause electrode damage, therefore voiding its warranty. See 7.2.2 maintenance section on page 21.
Fig. 1.b
No. Description
A Steam generator cylinder
B Room blower/manifold (optional)
C User interface/display
D On/Off, SET buttons
E Fill & tempering valves
F Drain pump
Fi
g
. 1.a
HL
DP DT EVF
8 9
3
13
6
10
2
4
1
11
7
12
5
A
F
B
C
D
E

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
7
1.2 Cylinder Life
1.2.1 Basics of the Steam Cylinder
The Steam Cylinder is the engine of the humidifier. As the humidifier operates water is evaporated and minerals are left
behind. Much of these minerals are removed through the cylinder drain. Some are deposited on the walls of the cylinder and
the cylinder electrodes. When a lower section of the electrodes develop a thick coating, the water level is raised to expose
clean electrode surface. Eventually minerals cover the electrodes’ entire length with a thick coating and little electrical current
can pass between them resulting in poor steam output. The humidifier can sense the low amperage and will display the E6
Cylinder Exhausted error code. There are several factors that influence cylinder life.
1.2.2 Water
Characteristics of water influence cylinder life and can vary greatly from place to place. Total mineral content of the water is
important. Equally important is what minerals are present in the water. Most water conditions result in flaky scale that
eventually fills the bottom of the cylinder until it can no longer function. Water with high silica content can result in a thin
glass-like coating on the electrodes that is highly insulating resulting in shorter cylinder life. Only cold water is to be used.
Water conductivity that is not matched to the correct cylinder will shorten cylinder life.
1.2.3 Water Filtration
Typically additional filtration of the incoming water supply is not necessary. If, however, mineral content is known to reduce
cylinder life excessively or if cylinder life proves insufficient then water filtration can be added. In most cases the addition of a
two element water filter can improve cylinder life. The filter should contain an activated carbon element and a particulate filter
element rated for 5 microns or less. Micron is a size measurement. The filter system should have a flow rate of at least
2 gpm. The activated carbon will absorb much of the mineral content while the particulate filter will catch any granular
material or sediment. It is important to remember that the increase in cylinder life will be accompanied by the need to replace
filter elements with each cylinder change.
1.2.4 Humidity Load and Cylinder Life
Humidity load demands have an effect on cylinder life. Normal installations where humidity capacity is properly sized require
only intermittent periods where full humidifier capacity is required. This allows the water level in the cylinder to be increased
only as electrode segments become insulated. This tends to maximize cylinder life.
Extraordinary installations that require constant operation at full capacity reduce cylinder life. The water level in the
cylinder is, on average, much higher, and the electrodes become completely insulated more quickly. Installations like this
may result in cylinder life of less than 1000 hours.
The importance of providing adequate humidifier capacity should not be underestimated.
1.2.5 Maximum Production
Another factor affecting cylinder life is the maximum production setting. A higher production
rate will result in a shorter cylinder life. For this reason DS-25 and RS-25 units are preset from
the factory at 70%. Further reductions in Maximum Production will extend cylinder life.
See Figure 1.c.
1.2.6 Structures Under Construction
In high end construction projects, humidification is often required while the structure is being finished. Humidification is
necessary to protect and stabilize wood floors, trim and decoration. Humidification load, however, in an unfinished structure
may be five to eight times higher than when finished. Elite Steam humidifiers may be operated while construction is underway
but, reduced cylinder life is to be expected and budgeted for. Good practice dictates that the steam cylinders also be
replaced once the project is complete.
1.3 Calculating Humidity Load
1.3.1 Steps to Determine Humidity Load
Total Square Footage
x Average Ceiling Height
x Factor From Table 1.2
x 1.05 for each Fireplace
Humidity Load in lbs./hour
x 2.88 convert to gallons/day
Gallons per Day Humidity Load
*Based on .5 air changes per hour.
Table 1.2 Pounds of Moisture / Hour / Cubic Foot *
Indoor Air
Temp °F 35% Indoor RH% 40% 45% 50%
68 0.00015 0.00018 0.00021 0.00024
70 0.00017 0.00020 0.00023 0.00026
72 0.00019 0.00022 0.00025 0.00028
* Based on .5 air charges per hour.
100% 20%
Cylinder
Life
Fig. 1.c

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
8
2. MODELS
There are two basic models available in two voltages. Duct models require selection of an additional kit.
Duct Steam Injection Room Steam Discharge
Fig. 2.a Fig. 2.b
MODEL LIST
PART NUMBER DESCRIPTION PARTS INCLUDED
RS 15P
Fig. 2.b Room steam dicharge, 15 gallons per day (5.5 Lbs per hour) 115-120v Complete Humidifier. GFX3 humidistat, code valve, water fill connector, water supply tubing
RS 25
Fig. 2.b Room steam dicharge, 35 gallons per day (12 Lbs per hour) 220-240v Complete Humidifier. GFX3 humidistat, code valve, water fill connector, water supply tubing
DS 15P
Fig. 2.a Duct steam injection 15 gallons Humidifier only, Kit selection required per day (5.5
Lbs per hour) 115-120v
Humidifier only, Kit selection required
DS 25
Fig. 2.a Duct steam injection 35 gallons per day (12 Lbs per hour) 220-240v Humidifier only, Kit selection required
DMNKIT
(not shown) Duct mount kit 8 ft. steam hose, nozzle, GFX3 humidistat, code valve, water fill connector, condensate hose, water supply
tubing, air proving pressure switch.
RMB 15
(not shown) Remote mount blower kit for DS 15
12 ft. steam hose, GFX3 humidistat, code valve, condensate
hose, water fill connector, water supply tubing, and thru-the
wall sleeve with 120v blower and grille pkg.
RMB 35
(not shown) Remote mount blower kit for DS 25 12 ft. steam hose, GFX3 humidistat, code valve, condensate hose, water fill connector, water supply tubing, and thru-the
wall sleeve with 240v blower and grille pkg.
EDMK4
(not shown) Economy Duct mount kit 4 ft. steam hose, nozzle, 5 ft. condensate hose, fill connector, air proving pressure switch (Humidistat not
included)

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
9
3. INSTALLATION
3.1 Positioning
The Elite Steam has been designed for wall mounting and, since it is an atmospheric
steam humidifier, should be placed close to the point where the steam will be used, to
minimize the steam hose length (and the amount of condensate). Certain clearances
must be maintained around the unit for safety and maintenance.
3.2 Mounting
3.2.1 Removing the front cover
The front cover is secured by four screws located at the four corners of the unit. Use a
phillips head screwdriver to remove the four cover screws. Then simply pull the front cover
away from the back part of the unit. Return it in reverse order.
Be careful not to over-tighten the screws.
Fig. 3.d
Fig. 3.e
Millimeters Inch
A (150 mm) 6”
B (150 mm) 6”
C (150mm) 6”
D (150 mm) 6”
E (600 mm) 24”
F max. 0.2°
Tab. 3.a
Fig. 3.a
Duct Steam Injection
C
D
Fig. 3.b
Millimeters Inch
A 150 mm 6”
B 1800 mm 72”
C 1800mm 72”
D 600 mm 24”
Tab. 3.b
Room Steam Discharge
Millimeters Inch
A 341 mm 13.5“
B 204 mm 8.1“
C 600 mm 23.7“
Kilograms Pounds
Weight empty 8kg 18 lbs
Weight packaged 10kg 22 lbs
Weight installed with water 12kg 26 lbs
Tab. 3.c
Unit Dimensions: Duct and Room Units
Fig. 3.c

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
10
3.2.2 Fastening to the wall
Drill the wall according to the drilling template supplied; then secure Elite Steam firmly to the wall by the screws and anchors
supplied.
Fig. 3.f

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
11
3.3 Plumbing
3.3.1 Water Characteristic Requirements
The humidifier must be supplied with water with the following characteristics:
• pressure between 20psi and 110psi or 0.1 and 0.8 MPa (1 and 8 bar)
• temperature between 33°F and 104°F or 1°C and 40°C
• flow-rate minimum of 0.45 L/min or 0.21gpm
• hardness no greater than 40°fH (equal to 400 ppm³ of CaCO), conductivity: from 125 to 1250 μS/cm
• absence of organic compounds
• the characteristics of the water of supply must fall within the following limits:
LIMIT VALUES FOR LOW SALT CONTENT WATER LIMIT VALUES FOR LOW NORMAL WATER
Units Min Max Units Min Max
Hydrogen ions (pH) 7 8.5 Hydrogen ions (pH) 7 8.5
Specific conductivity (R,20°C) μS/cm 300 Specific conductivity (R,20°C) μS/cm 125 500
Total dissolved solids (c R) mg/l (*) (*) Total dissolved solids (c R) mg/l (*) (*)
Dry residue at 180°C mg/l (*) (*) Dry residue at 180°C mg/l (*) (*)
Total hardness mg/l CaC³O 150 400 Total hardness mg/l CaC³O 0 200
Temporary hardness mg/l CaC³O = 200 Temporary hardness mg/l CaC³O = 150
Iron + Manganese mg/l Fe + Mn = 0.2 Iron + Manganese mg/l Fe + Mn = 0.2
Chlorides ppm Cl = 30 Chlorides ppm Cl = 20
Chlorides mg/Si2O = 20 Chlorides mg/Si2O = 20
Chlorine residue mg/l Cl- = 0.2 Chlorine residue mg/l Cl- = 0.2
Calcium sulphate mg/l CaS4O = 100 Calcium sulphate mg/l CaS4O = 60
Tab.3.d Tab.3.e
(*) Values dependent on the specific conductivity: in general: cR~=0.65*σR, 20°C; R180~=0.9*σR, 20°C
Note: There is no relationship between the hardness and conductivity of water.
Water Conductivity must be matched by specifications of the steam cylinder. Check or know the water conductivity of
the proposed site before installation. Replace the steam cylinder before startup if not correct. See Table 3.f right.
ELITE STEAM models Conductivity μS/cm Steam Cylinder
DS25, RS25, DS25LC, RS25LC, DS35, RS35 300-1250 35-14
DS25, RS25, DS25LC, RS25LC, DS35, RS35 125-500 35-15
DS15P, RS15P, DS15, RS15 125-1250 15-14
DS20A, RS20A 300-1250 20-14A
DS20A, RS20A 125-500 35-14 Tab.3.f
The following water types are not acceptable:
1. Softened water as this will lead to foam, electrode corrosion and greatly shortened
cylinder life.
2. Water containing disinfectants or corrosion inhibiters, as these are potential irritants.
3. Industrial water, boiler water or water from cooling circuits.
4. Any potentially chemically or bacteriologically contaminated water.
5. Heated water.
3.3.2 Water Supply Connection
We recommend the connection between the fill valve and the water supply line by a
soft poly hose capable of absorbing the water hammering in order to avoid damage to
the fill valve itself. The water line may be routed through the back or through the
bottom of the unit. With poly tubing, a tubing support must be used to prevent tubing
collapse and leaks. The fitting then threads onto the fill valve inlet located on the
bottom of the humidifier using a 3/4” G connection. Note that there is a strainer built
into the fill valve fitting underneath the unit, which will require periodic
cleaning, so be sure to allow clearance for access.
Fill valve and filter
Water drain
Fig. 3.g
Fig. 3.h
Extension tube
Water drain outlet

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
12
3.3.3 Water Drain
The Elite Steam also requires a connection to a drain. The drain line may be routed out the
back or bottom of the unit using the included angle fitting. The drain line can be 1-1/4” PVC,
CPVC or polypropylene. The drain line is not glued or otherwise attached to the humidifier so
it must be supported by itself. A coupling should be used. The Elite Steam includes a drain
tempering valve that runs whenever the drain pump runs and flushes cool water into the drain
line to insure the drain water temperature never exceeds 60°C or 140°F.
The drain water characteristics are:
• Connection 32mm or 1 1/4”
• Temperature 60°C or 140°F
NOTE: Drain line must be trapped under the unit to prevent flash steam from condensing in
the unit cabinet.
3.3.4 Drain Connections
When using a rear outlet drain passing through drywall, we suggest using a 1 1/4” extension tube type SJ (see Fig. 3.f).
When using a bottom outlet drain, attach the included 90° fitting to the drain outlet. The drain outlet may be rotated. Then
connect a 1 1/4” trap adaptor to connect to drain pipe.
IMPORTANT WARNING: The drain pipe must be free without back pressure. We recommend an external anti-flooding
device not supplied to protect from faults of external hydraulic circuits.
3.4 Steam distribution
3.4.1 Duct steam injection (Additional kit required)
The maximum allowed duct static pressure is 2 in WC.
The Elite Steam duct injection models include a plastic duct injection nozzle. See Fig. 3.i
Airflow 1000 cfm min.
Airflow
Min 8”
Height >8”
==
Airflow
1000 cfm min.
1/3 Height
Airflow
1000 cfm min.
=
=
8” min
24” min
Upstream 36”min
Downstream
Millimeters Inch
A 31.5 mm 1.24”
B 50 mm 1.96”
C 56 mm 2.20”
D 57.5 mm 2.26”
E 100 mm 3.93”
F 8 mm 0.31”
G 22 mm 0.86”
H 30 mm 1.18”
I 12 or 22 mm 0.47 or 0.87”
Fig. 3.i
Fig. 3.j
min. 5°
4
5
Drain Rate l/min gpm
DRAIN FLOW RATE 60 Hz 11.7 3.1

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
13
3.4.2 Duct Distribution (Additional kit required)
If a duct steam distribution nozzle is to be used, select an accessible location on the duct, allowing at least 36” of straight duct (no
elbows or obstructions) after the point where the nozzle will be installed and the clearances can be maintained as per the following
drawings. See Fig.3.j To mount the steam nozzle, cut or drill a 2-1/2” hole in the duct. Apply caulk to the to the mounting plate of the
nozzle. Attach the nozzle to the duct using 4 #10 sheet metal screws (supplied). Nozzle must be level or vertical with condensate
outlet to the bottom.
IMPORTANT: Allow 1 M ( 3 feet ) of straight duct downstream of the distributor pipes and nozzles for absorption of the steam.
Always allow 0.6M (2 feet) of straight duct upstream of the distributor pipes for evaporation of the steam. Turbulent air flow may
require longer lengths.
Optional stainless steel duct distributor pipe:
To install the distributor pipes:
1. Cut a round hole in the side of the duct to match the steam pipe and condensate return.
2. Apply silicone sealant to the mounting plate and insert the pipe through the hole and secure it with
sheet metal screws. See Fig. 3.k
3. Connect the steam and condensate hoses using the hose clamps supplied.
(Note: end support bracket supplied only with 36” and longer distributors.)
3.4.3 Return Condensate Connection
The return condensate hose from the nozzle, etc. must be trapped. Coil the hose into a vertical loop
and secure it below the nozzle, etc. This trap prevents steam from being released into the cabinet.
The hose end may be run through the knockout at the top of the humidifier and be inserted into the
hole located on top of the fill cup. The hole may be enlarged to suit. See Fig.3.l.
3.4.4 Steam Hoses
IMPORTANT WARNING: NINETY PERCENT (90%) OF ALL OPERATION PROBLEMS ARE CREATED BY IMPROPER STEAM
PIPING FROM THE HUMIDIFIER UNIT TO THE DUCT DISTRIBUTOR PIPES.
To avoid these problems, remember one simple fact when running the steam hose: steam naturally flows up hill, and condensate
naturally flows downhill. Run the steam hose or piping to avoid any kinks, sharp elbows, or low spots that could collect or restrict the
flow of steam to the distributor pipe, or the flow of condensate back to the humidifier. Support the hose adequately to avoid sags.
The following diagrams are to provide you with some guidelines. If you have a situation you are unsure of, please contact the factory
for instructions.
Fig. 3.j
Fig. 3.l
25-12 STEAM CYLINDER HOSE ADAPTER

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
14
20% 5%
20% 20%
5%
1,5 m (5 FT max.)
3 m (10 FT max.)
20%
0,9 m (3 FT max.)
1,5 m (5 FT max.) 1,5 m (5 FT max.)
YES
NO
P - TRAP
NOTE: HEIGHT OF TRAPSMUSTBE GREATER
THAN THEDUCT STATICPRESSURE
NOTES:
• SLOPEPIPINGUPIN DIRECTION OFSTEAM FLOWAT20% OR GREATER, WHICH MEANS65,5mm x305mm (2 1/2” PER FOOT);
• SLOPEPIPING DOWN IN THE DIRECTION OFSTEAM FLOWAT 5% OR GREATER, WHICH MEANS 20mm x305mm (3/4” PER FOOT);
• MAX. LENGTH OF RUBBERSTEAM HOSEIS 3 m (10 FT).
• HEIGHT OF P-TRAPSMUSTBE GREATER THAN THE DUCT STATIC PRESSURE.
TYPICAL INSTALLATION
WHEN UNITIS ABOVE
THE DISTRIBUTORPIPE
GENTLEBEND
OBSTRUCTION
SUPPORTED STEAM HOSE
AND/ORCOPPERPIPE DRAINS
IF NO TRAP WITH TRAP
DRAINS
IF NO SLOPE
NO SLOPE
NO SLOPE
KINKED
NO TRAP
UNDRAINED
ELBOW UNDRAINED
ELBOW
NO DISTRIBUTION
PIPE DRAIN
SAG
Fig. 3.m
IMPORTANT: Maximum length of rubber steam hose is 4m (12 feet.). Insulated copper tubing may be up to 6m(20feet) in
length. In all cases, minimize sharp bends and elbows. Use 2 - 45° elbows instead o f 90°s.
Hose inner diameter = 7/8” ( 22 mm); Hose outer diameter = 1-1/4” (30 mm).
3.4.4 Remote Mount Blower
Remote Mount Blowers, are used to distribute the steam directly into the room. The drawings show the minimum recommended
distances to avoid the flow of humidified air from coming into direct contact with persons, lights, electrical appliances, and surfaces
before the steam has been totally absorbed by the environment. For further details on the assembly, the electrical connections and
the use of a Remote Mount Blower, please refer to the specific instruction manual.
20%
A
CB
D
Millimeters Inch
A 150 mm 6”
B 1800 mm 72”
C 600 mm 24”
D 2100 mm 84”
Tab. 3.g
Fig. 3.n

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
15
3.5 Power wiring Check that the power supply voltage to be connected matches the value indicated on
the rating plate inside the electrical panel.
Insert the power and ground connection cables into the electrical panel compartment
using the strain reliefs supplied, and connect to the terminals. An external fused
disconnect must be installed. See Fig. 3.o
All wiring must be in accordance with local, state and national electric codes.
NOTE: to avoid unwanted interference, the power cables should be kept separate
from any control wiring.
NOTE: Tolerance allowed on main voltage =-15% to +10%.
Connect power wires to the power terminal block located at the bottom left of the
control module, polarity does not matter. See Fig. 3.p
Connect the ground wire to the unit’s chassis ground, located just behind the power
wiring terminal block. See Fig. 3.q
Model Power supply (single phase) Steam Output (lbs/hr) Steam Output (kg/h) POWER (kW) CURRENT (A) EXTERNAL POWER WIRES EXTERNAL FUSE (A) OR BRAKER
DS15 110Vac 50/60Hz 5.5 2.5 1.80 16.40 AWG10 25
RS15 110Vac 50/60Hz 5.5 2.5 1.80 16.40 AWG10 25
DS35 230Vac 50/60Hz 12 5.4 3.89 16.95 AWG10 25
RS35 230Vac 50/60Hz 12 5.4 3.89 16.95 AWG10 25
3.6 Control wiring Elite Steam allows connection of any simple or automatic humidistat, and safety
devices such as high-limit humidistat, air flow proving switch, and remote on/off.
The humidifier is operated by the closing of a mechanical humidistat H, or by the
closing of a voltage-free remote contact, or alternatively by a combination of both. The
most common is a combination of a humidistat and pressure switch. The diagrams
in the figures show the connections to be made on the terminal block, in case of:
Fig. 3.u Operation performed by a simple enabling contact;
Fig. 3.t Operation controlled by an external mechanical humidistat;
Fig. 3.v A combination of both humidistat and pressure switch (most common).
Contact AB-AB:
• closed: humidifier enabled to produce steam (production starts when humidistat
closes);
• open: steam production is immediately stopped.
The remote on/off contact is usually a series of external potential-free contacts that
enable the humidifier to produce steam when all of them are closed, indicating the
duct/AHU is ready to accept steam. Connect the 12500 Pressure
Switch NO and C terminals to the AB-AB contacts.
For example,
• fan contact closes when fan is running;
• downstream cooling coil contact closes when coil is off;
• etc.
Contact IN-GND:
• closed: steam production starts if contact AB-AB is closed
• open: steam production is stopped after 5 sec.
Fig. 3.o Fig. 3.p
Fig. 3.q
L1 L2
Fig. 3.r Fig. 3.s
Fig. 3.t Fig. 3.u Fig. 3.v

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
16
3.6.1 Connect the GFX3 Humidistat for On/Off Operation:
1. Remove the humidistat from the base, squeeze the louvered base at the top and bottom. To remove the humidistat from
the wall, lift up on the humidistat and pivot top away from wall.
2. Before wall mounting, please remove the black foam gasket.
3. Before return air duct mounting, please remove the breakout piece.
4. If return air duct mounting, route wires between humidistat and base.
5. Mount the sensor outside the house. Do not mount on South side of the house or in direct sunlight. Place at least 4 feet
away from any exhaust vent. If in air intake, place 1 foot or closer to outside wall. Place at least 6” higher than possible
snow. Do not route sensor wire near high voltage wires.
6. Connect the GND-IN terminals on the humidifier to the HUM terminals on the GFX3 Humidistat. Connect the GND-24V
terminals to the ACL-ACN terminals on the GFX3 Humidistat. see Fig.3.x
3.6.2 Modulating Operation
Connect an external 0...10 Vdc modulating input between terminals IN-GND. Connect any
Safety Switches (high-limit, air flow switch, remote on/off) in series to terminals AB-AB. If
no safety switches are used, then a jumper must be installed between AB-AB. DO NOT
apply any voltage to AB-AB.
3.6.3 Connect the GFX50 humidistat for Modulating Operation
To select signal modulating see Fig 3.y Connect the power supply to the GFX50 G and G
O terminals, using the terminal GND and 24V on the Elite Steam. Note MODULATING
OPERATION requires a change in signal type. See SEC. 5.1.1 page 19.
Connect an external signal to the GFX50 using the terminal IN from the Elite Steam and
AOUT in GFX50.
See the diagram below.
GFX3 HUMIDISTAT GFX50 HUMIDISTAT AIR CONDITIONER RELAY INTERLOCK
N2
GND
N1
AB
AB
GND
IN
NO
C
NC
C
NO
GND
24V
AC L AC N
HUM
SNSR
OUTDOORTEMP. SENSOR
(not used in manual mode)
Elite Steam
ON DIP
1 2 3 4
A
DCD
DIP SWITCH SETTNGS
FOR HUMIDISTAT ONLY OPERATION
ON
OFF
OFF
ON
3.6.4 Safety and High Limit Switches
Remove the jumper between terminals AB-AB and connect any simple high-limits, air flow switch, 12500 pressure switch, and
remote contacts in series to terminals AB-AB; otherwise, if no such dry contacts are available, the jumper must remain in place
between terminals AB-AB. DO NOT apply any voltage to AB-AB.
Thread the control wiring through the bottom of the unit, and the strain relief (see photo at top of previous page), and then up the
side of the control module to the top right wiring terminal blocks. Connect the control wiring to the control wiring terminal blocks
found at the top right side of the control module.
3.6.5 Air Conditioner Relay Interlock
Auxiliary DPDT safety relay: Use this method in the following situations:
1. To prevent the air conditioner from running when there is a call from humidity. The DPDT relay will open the “Y” circuit and close
the “G” circuit for operation while a call for humidity is present. Demand for humidity will override call for cooling.
2. In systems using a thermostat where G and Y are a single circuit. The DPDT relay will allow blower operation to occur without
back-feeding the compressor.
Do not use this method when simultaneous humidification and cooling will be desired. Use a high limit humidistat in to avoid
condensation in ductwork.
The humidistat should be set to OFF during the air conditioning season if humidification is not desired.
For variable speed or DC systems, consult furnace manufacturer.
PRESSURE
SWITCH
EXTERNAL
REGULATOR
Fig. 3.w
Fig. 3.x Fig. 3.y Fig. 3.z

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
17
3.7 Wiring Connections:
Terminals Functions Electrical specifications
L1-L2 -GROUND Power supply and Ground connections Power supply 110 VAC 1-phase 50-60Hz 1.86kW or 230VAC
1-phase 50-60Hz 4.05kW
KEY Programming port Connecting to Programming port or supervisor
AB-AB Remote enabling input Imposes an external NO contact ; Rmax=300 Ohm; Vmax=33
Vdc; Imax=6mAdc; humidifier enabled = contact closed
IN-GND Control signal input If programmed 0...10V:
Input impedance 10 kohm
If programmed ON-OFF:
Vmax 33Vdc
Imax = 5mA Rmax = 300 Ohm
NC-C-NO NC alarm contact
Common alarm contact
NO alarm contact
250V; 8Amp max with resistive load; 4 Amp max with inductive
load
NO-C External fan relay 250V; 8Amp max with resistive load; 4 Amp max with inductive
load
24GND Power for external humidistat Power supply for external humidistat 24 Vac; 2 Watt
3.7.1 Wiring diagram of controller
KEY FOR PROGRAMMING PORT:
DP = DRAIN PUMP
DT = DRAIN TEMPERING VALVE
HL = HIGH-LEVEL SENSOR
EVF = FILL VALVE
CONNECTED
TO GROUND
POWER SUPPLY
(110VAC 1-PHASE 50-60 HZ
OR
230 VAC 1-PHASE 50-60HZ)
24VAC FOR
EXTERNAL
HUMIDISTATS
EXTERNAL DUCT FAN
ALARM
HUMIDISTAT
AIR PRESSURE SWITCH
PROGRAMMING
PORT
IN GND AB AB N1 GND N2
NO C NC C NO
24Vac GND
KEYBOARD
EXT FAN ALARM KEY
HL
N
EVF
DP
N
F
INT
FAN
E1
E2
L1 L2
8
2
4
EMBEDDED
BLOWER
ON-OFF
BOTTON 6
EXTERNAL FUSED
DISCONNECT TO BE
INSTALLED (NOT
SUPPLIED) RESPECT
LOCAL CODES
HL
STEAM
BOILER UNIT
DP DT EVF
Fig. 3.z.1

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
18
4. START-UP
IMPORTANT WARNINGS:
1. Before starting, check that the humidifier is in perfect condition, that there are no water leaks and that the electrical parts
are dry;
2. Do not connect power if the humidifier is damaged or even partially wet!
When installation is completed, flush the supply pipe for around 10 minutes by piping water directly into the drain, without sending it
into the humidifier; this will eliminate any scale or residues that may cause foam when boiling.
4.1 Startup Checklist
Before starting the humidifier, the following should be checked:
Water is connected, the line has been flushed, and external valves are open.
Drain is connected, run to an open drain, and has a trap under the unit.
Electricity is connected in accordance with instructions, local codes and data labels in the unit.
The power fuses are installed and intact.
All control wiring is done and tested.
Airflow switch is wired to open on air flow loss.
Hi-limit humidistat is wired to open on humidity rise above set point.
Unit wires have been checked to make sure they and all connectors are tight from shipping.
The steam hose(s) are run correctly with no sags or kinks and sloped properly according to the manual.
Condensate hoses are run correctly with no sags or kinks and sloped properly according to the manual.
4.2 The Elite Steam Controller
The Elite Steam controller features a comprehensive information display that shows the operation of the system at a glance:
1. Display is % of nominal capacity
2. Maintenance
3. Display is amperage (default)
4. Steam is being produced
5. Cylinder filling
6. Foaming
7. Water presence inside the cylinder
8. Cylinder draining
9. LEDs indicate: power (yellow), operation (green) and alarms (red)
10. Drain button for manual draining of cylinder and confirming parameter values
11. ON/OFF button
12. Reset button to reset alarms and access parameters
13. Level of output: 33%, 66%, 100%
14. Fan relay is activated
The Elite Steam is now ready to operate.
4.3 Starting Elite Steam
Insure that the external power is turned on.
Push the top part of the On/Off button so that the I part is in. The yellow Power LED will be
lit. The Elite Steam is now ready to operate.
When there is a call for humidity, Elite Steam will close its power relays and send power to
the electrodes in the plastic steam generator. The green Operation LED will light, indicating
that operation has begun.
4.4 Starting with a new cylinder
When starting with a new cylinder, you should activate the cylinder cleaning function as follows:
1. Switch Elite Steam off.
2. Press and hold both buttons, “reset” and “drain”, and switch Elite Steam back on. When the
wrench blinks then release the two buttons.
3. Press and hold “reset” until the display shows 04.
WARNING: DO NOT confirm any value higher than 04. If 05 or higher is displayed, press “reset” until the display goes back to
the normal operating mode and restart from step
4. Press “drain” (minimum 1 second): the cleaning starts and the display shows PC.
During the cleaning, the electrodes are powered and water is filled in until it touches the high-level sensor or the phase current equals 20A,
whichever occurs first. After either of the events is detected, the boiler is fully discharged with the electrodes un-powered (the drain pump and
the drain tempering valve are activated for 3 minutes). Warming the filling water helps washing out any mould release or dirt. General Filters,
Inc. recommends doing two cleanings when starting a new boiler. After the cleaning ends, the humidifier starts the regular duty. When starting
the unit with a new or empty cylinder, it may take a significant amount of time (hours) for the unit to build up enough mineral concentration to
reach rated capacity. This time can be shortened by the addition of Alka-Seltzer through the steam outlet on top of the cylinder.
1
2
4
5
6
9
1012
13
14
11
3
7
8

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
19
5. OPERATING ELITE STEAM
5.1 Displaying Information
By pressing the “reset” button for 2 seconds, the display will loop from amperage to production in % of the maximum production to
the hour counter and back to amperage:
Fig. 5.a
1. Amperage: it is the value of the current that flows through the water making it boiling off (default display)
2. Production %: it is the current production expressed as a percentage of the humidifier’s capacity
3. Hour counter, expressed in tens; for instance, when the display shows 13 the real hour value will be between 130 and 139
hours.
5.1.1 Select Signal Type
The Elite Steam is preset for the included GFX3 humidistat (signal type 0). If the included humidistat is used, this section may be
omitted. If another humidistat is used, review this section to see if changes are needed.
1. Switch Elite Steam off.
2. Press and hold both buttons “reset” and “drain” and switch Elite Steam back on. When the wrench blinks,
release the
2 buttons.
3. Press “Reset” until the display shows 02. WARNING: DO NOT confirm any value higher than 04. If 05 or higher is
displayed, press “Reset” until the display goes back to the normal operating mode and restart from step 1.
4. Press “drain” (minimum 1 second) to confirm: the display shows “P1” then the current signal type and “set”
5. Press “Reset” to change signal type between 0 and 1:
0 = On-Off humidistat such as the GeneralAire “M” or “GFX” series humidistat.
1 = external 0...10 Vdc modulating signal such as the GeneralAire ADCD series humidistat
6. Press “drain” (mininimum 1 second) when done to confirm the new value of P1 and exit to the normal operating mode.
7. Switch Elite Steam off: you can now proceed with connecting the control wiring.
5.2 Changing The Maximum Production
The maximum production can be adjusted between 20% to 100% of the nominal production in steps of 5% in order to suit the
environmental characteristics. DS25 and RS25 Maximum production is factory set at 70%.
1. Switch Elite Steam off.
2. Press both and hold both buttons “Reset” and “Drain” , and switch Elite Steam back on. When the wrench blinks;
release the 2 buttons.
3. Press “reset” until the display shows 01. WARNING: DO NOT confirm any value higher than 04. If 05 or higher is displayed,
press "Reset" until the display goes back to the normal operating mode and restart from step 1.
4. Press “drain” (minimum 1 second) the display shows “P0” then the current Maximum Production Percent and “set”.
5. Press “reset” to change the Maximum Production in steps of 5% between 20% and 100%.
6. Press and hold “drain” (minimum 1 second) when done to confirm the new Maximum Production and exit to the normal
operating mode.
5.3 Activating Manual Drain
Press and hold the “drain” button on the front of the unit until the cylinder is drained. Note: Water will continue to flow from the
tempering valve after the cylinder is empty.
5.4 Resetting the hour counter
The hour counter should be reset every time the cylinder is changed in order to reset and restart the internal maintenance timer:
1. Switch Elite Steam off.
2. Press and hold both buttons “Reset” and “Drain” and switch Elite Steam back on. When the branch
blinks; release
buttons.
3. Press and hold “reset” until the display shows 03. WARNING: DO NOT confirm any value higher than 04. If 05 or higher is
displayed, press “reset” until the display goes back to the normal operating mode and restart from step 1.
4. Press “drain” (minimum 1 second) to confirm: the hour counter will be reset at once and Elite Steam will go back to the normal
operating mode.

Elite Steam +030222075 Rev. 3.4 – Sept. 2011
20
5.5 Using the GFX3 Humidistat
Press to select OFF, MANUAL or AUTO mode (if outdoor sensor is connected).
OFF mode: The humidifier is turned off.
MANUAL mode: The GFX3 will work to maintain the single humidity selected. You can set
your desired humidity level by pressing or . The humidifier will turn ON or OFF
according to your manual setting. (The humidifier will operate when the measured relative
humidity falls more than 2% below the set point.) Humidity will have to be lowered when
weather is colder or if condensation is suspected.
AUTO mode: The GFX3 will automatically raise the humidity as the outdoor temperature
increases. This provides the highest possible humidity. The GFX3 will automatically lower the humidity as temperatures drop. This
minimizes the risk of condensation on cold surfaces like windows. You can adjust the Auto Humidity Index Set Point from 0 (low) to
10 (high) by pressing or . The Humidity Index is based on the outdoor temperature and indoor humidity. The humidifier will
switch ON/OFF according to the calculated auto humidity index set point. Lower Index settings are for older homes with less
insulation and vapor barriers. Higher Index settings are for newer homes with complete vapor barriers, triple pane windows and high
R value insulation. If condensation occurs reduce Index setting by 2 points until condensation stops.
NOTE If the outdoor temperature sensor fails, flashes and the unit will default to MANUAL mode.
To toggle between indoor / outdoor temperature and indoor humidity: Press .
To change the temperature unit: Press °C / °F.
To set the temperature / humidity offset in MANUAL or AUTO mode:
1. Simultaneously press and when viewing the temperature or humidity reading.
2. Use or to change the setting (-3 to 3).
3. Press and simultaneously or wait 5 seconds to confirm and move onto the next setting.
WARNING: Do not allow excess humidification. Excess humidity can cause condensation and enable mold and mildew growth.
5.6 Alarms
In the event of an alarm, the red alarm LED will flash, the alarm relay will close, and the alarm code will flash in the display. Multiple
alarms will flash in sequence, alternating with the main display. Pressing the sel button for 2 seconds will reset the alarms, although
still active alarms will continue to display.
Dis
play Description Action Red Led Alarm Relay Notes
-- Remote on-off open Unit disabled Off Off
EE Internal memory error Unit disabled On On
E0 Control board configuration not valid Unit disabled On On Turn off, check control board, reprogram
E1 High current alarm Unit disabled On On Turn off, check connections, check
cylinder (no limescale bridges between
electrodes, no electrodes short-circuited)
E2 Low production, low supply water
conductivity or excessive
foam/limescale in the cylinder
Unit disabled.
Press “reset/sel” key for 1 seconds to reset. On On Check supply water conductivity (too low?), replace the cylinder.
E3 Cylinder almost exhausted, already
used for 2000 hrs Press “reset/sel” key for 1 seconds to reset. Off Off Change cylinder (not urgent)
E4 Fill alarm, unable or slow fill
(current does not increase within
timeout)
Press “reset/sel” key for 1 seconds to reset, otherwise
the warning will be reset automatically every 10
minutes until the supply water is available again.
On On Check water supply and fill valve; check
drain pump for leakage
E5 Drain alarm, unable to drain
(current does not decrease within
timeout)
Press “reset/sel” key for 1 seconds to reset On On Check drain pump and drain connection
E6 Cylinder exhausted
(critical performance detected) The warning is automatically reset if Elite Steam can produce the demand, otherwise turn off and then on. Off Off Change cylinder (urgent)
E7 Foam detected Press “reset/sel” key for 1 seconds to reset Off Off If it continues, do some cleaning cycles
(read chap. “Starting with a new
cylinder”)
E8 Cylinder lifetime expired (3000 hours) Unit disabled: Reset the hour counter (read chap.
Resetting the hour counter”) On On Change the cylinder if necessary
E9 High controller temperature (above
176 °F / 80 °C) The warning is automatically reset if the temperature decreases below 176 °F / 80 °C. Off Off Check the ambient temperature, replace the controller.
Suggested
Setting Outdoor Temperatures
15% -20˚F -29˚C
20% -10˚F -23˚C
25% 0˚F -18˚C
30% +10˚F -12˚C
35% +20˚F - 7˚C
40% +30˚F - 1˚C