Genesis Pure E600 User manual

Wi-Fi EasyMeshTM supported
Revision 2.0 - October 2023 - Copyright ©2023 Genexis Netherlands B.V. All rights reserved.
Multiple languages of this document and additional product information are availableon hps://genexis.eu/product/pure/downloads
Genexis assumes no responsibility for any inaccuracies in this document. Genexis reserves the right to change, modify, transfer, or
otherwise revise this publication without notice.
Pure
E600
Installation Guide

Geing started
Check if the following items are in
the giftbox:
• Genexis Pure E600
• Power adapter
• Network cable
• Labels (self-adhesive)
• Rubber feet (self-adhesive)
• Plugs & screws
Label position
The product label is positioned on the boom
of the Pure E600 device and additional labels
are included in the giftbox.
Genexis EasyWiFi app
Installation and management of the Genexis
Pure E600 device can be done with help of the
mobile application Genexis EasyWiFi. Please
follow the steps on the left page.
Warning: Do not cover the device with
anything, or put the device horizontally on a
at surface, becasue this will interfere with
the ventilation of the Pure E600.
Operation Temperature 0°C ~ 40°C
Placement
Pure E600 supports two placement options;
standing (desktop) and wall-mounted. It is
recommended to place the device ‘away’ from
obstacles and objects.
Standing
1. Place the device on a at surface
using the stand.
2. The rubber feet need to be aached to the
stand accessory for stable placement.
Wall-mount
1. Download and print the drilling
guide from hps://genexis.eu/product/pure/
downloads
2. Use the drilling guide to drill the holes, insert
plugs and put screws into place.
3. Remove the stand from the device by sliding
it towards the front.
4. Store the stand in a safe place.
5. Use the wall mount points on the back
of the Pure E600 to mount the device
to the screws.
Installation guide
Download app and
follow the steps
Scan QR-code
1
2
You're just a few steps away to install your
device via the Genexis EasyWiFi app
Installation with use of app

Seing up the Pure
1. Connect a network cable between your
broadband outlet and the Pure E600 WAN
port (red connector).
2. Connect the supplied power adapter to
the Pure E600 and plug the adapter into a
power socket.
3. Flip the ON/OFF switch at the back of the
device to turn it on.
4. Wait until Status, Uplink and Internet LEDs
turns solid green.
Your Pure E600 is now ready for use.
Connecting your telephone
You can connect two regular plain telephones
to the Pure E600.
1. Insert a telephone cable of a regular wired
telephone in one of the telephone ports
(green connectors).
Switching the WiFi ON/OFF
The WiFi function of the Pure E600 can be
switched ON or OFF by means of
the Mode buon.
• Switch OFF: On the Pure E600, press and
hold the Mode buon until the WiFi LED
turns o.
• Switch ON: On the Pure E600, press and
hold the Mode buon until the WiFi LED
turns on.
Connecting to the wireless network
Automated pairing
You can connect your personal device to the
Pure E600 by scanning the QR-code on the
label of the Pure E600 or use the Mode buon
(WPS function) of the Pure E600. Please
check on your personal device how this can be
initiated. Before pairing, make sure the WiFi
LED is solid green. If not, switch the WiFi ON as
described in this installation guide.
Manual pairing
You can connect your personal device to the
Pure E600 via manual pairing using the WiFi
network name and WiFi key printed on the
label of the Pure E600.
1. Perform a search of available wireless
networks on your personal device.
2. Select the WiFi network name printed on
the label.
3. Enter the WiFi key printed on the label.
Using the web interface
When connected to your network, you can
access the Pure E600 web interface to change
your device seings.
1. Use a web browser on your personal device
and navigate to ‘GUI’ as printed on the label
of the Pure E600.
2. Login by inserting the ‘Username’
and ‘Password’.
3. If required, change your device conguration.

Reset buon (recessed)
Reboot - press and release once
Factory reset - press and hold until all LEDs
start fast blinking green
ON/OFF switch
Switch ON – ip the switch to ON
Switch OFF – ip the switch to OFF
WAN port
Reset buon
LAN ports
USB 2.0
port
Telephone
ports
ON/OFF
switch
Power port
Status LED
Green - system is operational ready
Yellow - system startup
Yellow (blinking) - system is not ready yet
Blue - automated pairing successful
Blue (blinking) - automated pairing in progress
Red - system / booting failure
O - power o
Uplink LED
Green - uplink established
O - no uplink available
Internet LED
Green - connected to broadband
Green (blinking) - broadband connectivity failed
O - no broadband connectivity
Telephone LED
Green - telephone service operational
Green (blinking) - seing up telephone service in progress
O - no telephone service
WiFi LED
Green - wireless network is active
O - wireless network is disabled
Mode buon
Pairing (WPS) – press and release once
WiFi ON – press and hold until WiFi LED turns solid green
WiFi OFF – press and hold until WiFi LED turns o
LED & button overview Port overview

Support
Is the Status LED solid red?
Contact your service provider.
Is the Status LED not solid blue after
automated pairing?
Automated pairing between the Pure E600
and your personal device failed. Please follow
the instructions again to connect your personal
device to the wireless network.
Is the Status LED blinking yellow?
The Pure E600 is being upgraded with new
software. Please wait until the status LED turns
solid green again.
Is the Uplink LED o?
Pure E600 does not have a connection with
the broadband network. Please verify your
wired connection with the broadband outlet or
contact your service provider.
Is the Internet LED o for 5 minutes
Pure E600 does not have an internet
connection. Please contact your
service provider.
Is the WiFi LED o?
The WiFi of the Pure E600 is turned OFF.
Please turn the WiFi ON as described in this
installation guide.
Return the Pure E600 to factory default seings
With the reset buon you can reset the Pure
E600 to its factory default seings. You can
press this buon with a small pin or paperclip.
1. Press and hold the reset buon until all LED’s
start fast blinking green.
2. Wait until the Status LED turns solid
green again.
Your Pure E600 is now setup again with factory
default seings as printed on the label.

EU Declaration of Conformity
Company Name
Genexis Netherlands B.V.
Company Address
Lodewijkstraat 1a
5652 AC Eindhoven
The Netherlands
Name and title of authorized person
Maarten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven 2021-06-21
The Netherlands
Hereby, Genexis Netherlands B.V. declares that the radio equipment type Pure E600 is in compliance
with Directive 2014/53/EU, Directive 2009/125/EC, Directive 2011/65/EU and Delegated Directive
2015/863.
The full text of the EU declaration of conformity is available at the following internet address: hps://
genexis.eu/product/pure/red/pure-e600
Frequency bands and maximum radio frequency power transmied
The Pure E600 operates in the frequency bands of 2,4 Ghz and 5Ghz.
The maximum radio frequency power transmied in these bands is:
20 dBm(100 mW) (EIRP)for the 2400 MHz – 2483.5 MHz band
23 dBm (200 mW) (EIRP)for the 5150 MHz – 5350 MHz band *
30 dBm (1000 mW) (EIRP) for the 5470 MHz – 5725 MHz band
* In EU, 5150 – 5350 MHz is restricted to indoor.