GENI ILDW-7016156-00D-11 User manual

User Manual of
16x3W 3IN1 LED Single-line Wash Light
ILDW-7016156-00D-11
Introduction
Containing the working modes of DMX, AUTO and MANUAL, ILDW-7016156-00D-11 is a single-line wash light with
16pcs of 3W 3IN1 LED which can be controlled by 8, 4, 2 and 1 sections, and the light emitted has the effects of color
changing, dimming, strobe and dreamlike effect. This product is user-friendly with competitive price and significant effect
which is suitable for various entertainment places and families.
Please read the instruction carefully before installing and save for future reference.
Caution:
Corrosive and deliquescent chemicals will damage the coating of outer casing.
The normal operating temperature must not exceed 40℃and the humidity is 0~95%. Otherwise, the lifespan of light will be
affected.
Indoor using
Cautions:
Input voltage of the power supply should be in line with the rated voltage, a tolerance of ±10℅is permitted.
Make sure it’s entirely grounded.
Do not take the light apart when there’s problem, professionals should be asked for maintenance.
Technical Parameters：
1. Power supply: AC90-264V 50Hz/60Hz
第页共5 页
1

2. Power: 50W
3. Light Source: 16 pcs of 3W 3IN1 LED
4. Functions: DMX，ANTO，MANUAL，MASTER/SLAVE，MEMORY
5.DMX channel：26
6.IP rating：IP65
7. Dimensions：L1000*W82*H135mm
8. N/W：5.0 KG
Packing List
zILDW-7016156-00D-11 16x3W 3IN1 LED single-line led wash----------------------------------------------------------1unit
zPower cable------------------------------------------------------------------------------------------------------------------------1 piece
zDMX line--------------------------------------------------------------------------------------------------------------------------1 piece
zUser manual-----------------------------------------------------------------------------------------------------------------------1 piece
Panel:
1、LCD display 2、touch switch UP 3、touch switch DOWN 4、safety clamp 5、DMX IN 6、power IN 7、power OUT 8、
DMX OUT
Installation：
Installation way: the light can be installed on the ground horizontally. Please fix the hand-wheel and screws tightly for the sake
of safety.
a) Horizontal Installation
b) Hanging Installation
第页共5 页
2

Functions:
I. Reset at powered up
The system initializes at power up enters the working mode of last time before turned off.
II. Menu and Display
Keep pressing UP or DOWN and the following menus switch automatically.
001~512 Pgx Spx
Sbx
Gxx Bxx XXX
Fdx
Rxx
Explication：
X is the numerical value of 0~9
XX is the numerical value of 00~10
XXX is the temperature of the light board
III. Slave Mode：
1. DMX mode and address setting：
Keep pressing MENU and the working mode will switch automatically. Stop pressing MENU when it switches to DMX and it
enters the DMX mode, then the DMX address can be modified by pressing UP and DOWN; keep pressing UP and DOWN and
the value can be change fast; the range of address setting is 001~512.
2. Functions of DMX Mode:
CH1 CH2 CH3 CH4 CH5 CH6~CH26
0~40 Black
Out NA NA NA NA NA
41~80 Dimmer Flash All Red All Green All Blue NA
81~120
Dimmer Flash Red 1 Green 1 Blue 1 Red2,Green2,Blue2~Red8,Green8,Blue8
121~160Color
Flash Flash Color NA NA NA
201~240Color Speed NA NA NA NA
第页共5 页
3

0~29
Program1
30~59
Program 2
60~89
Program 3
90~119
Program 4
120~149
Program 5
150~179
Program 6
180~209
Program 7
241~255
Dream Flow Speed Fade
210~255
Program 8
NA NA
3. Definition for the pins of DMX socket：
Definition for the pins of male and female DMX sockets: Pin1 = Gnd Pin2 = Dmx- Pin3 = Dmx+
4.Connection way of DMX online mode is as follows：
DMX console
Test for DMX online mode：Connect the lights according to the way shown in the above drawing with 3-pin DMX cable; set
each light to be DMX mode and unify the reception address(available range:001-512); the lights run synchronously when
connected with DMX signal source.
Ⅳ. Master mode
1. AUTO：
Keep pressing MENU and the working mode will switch automatically; Stop pressing MENU when it shows as the drawing
below and it enters the AUTO mode, then the DMX address can be modified by pressing UP and DOWN.
Pgx Spx
Sbx
Fdx
Parameters:
Pgx (1~9): select internal program and there’re 9 available.
Spx (1~9): select the running speed of internal program, and there’re 9 gears of speed available; 01 is the slowest and 9 fastest.
第页共5 页
4

Sbx (0~9): select strobe frequency for each step of the internal program.
Fdx (0~9): select the internal program to run the dreamy effect and there’re 10 available; 01 runs the fastest and 9 runs the
slowest.
Notes: parameters of strobe effect are superior to that of the dreamy effect; If Stb is not 0, then the program will run as per
strobe effect but not dreamy effect even if Fad is not 0.
2.MANUAL：
Keep pressing MENU and the working mode will switch automatically; Stop pressing MENU when it shows as the drawing
below and it enters the MANUAL mode, then the DMX address can be modified by pressing UP and DOWN.
Rxx
Gxx Bxx
Rxx (00~10): set brightness of red
Gxx (00~10): set brightness of green
Bxx (00~10): set brightness of blue
3. Display of Temperature：
Keep pressing MENU and the working mode will switch automatically; Stop pressing MENU when it shows as the drawing
below and it shows the temperature.
XXX is the current temperature of the light board。
XXX
4. MASTER/SLAVE: The slave can run synchronously under DMX mode when the master is underAUTO or MANUAL mode.
Elimination of Common Malfunctions：：
malfunctions items need to be examined Measures
Light doesn’t work
1.Check to see if the input voltage is
suitable;
2. Check to see if the fuse burns out;
1.Confirm the input voltage is in line with the
required voltage of light;
2.replace with fuse of same specification
LED is dim 1. Check to see if the input voltage is suitable 1.Confirm the input voltage is in line with the
required voltage of light;
DMX doesn’t
incept signals
1. Check to see if the connection for the
electrodes of DMX signal is correct;
2. Check to see if the working mode is DMX
1. Correct the electrodes of DMX signal.
2. Set it to be DMX mode.
第页共5 页
5