Genie DFE-PROX-DUO User manual

User Manual
Please read these instructions carefully before operating the unit
and keep for further reference.
Multi-Card Technology Reader
- 13.56MHz, DesFire EV1 / EV2
and EM / HID
DFE-PROX-DUO

Contents
ii
1.1 Product Features...........................................................................................3
1.2 Product Dimensions.....................................................................................3
1.3 Specification.................................................................................................4
1.4 Mounting ......................................................................................................4
1.5 Recommendation.........................................................................................5
1.6 Wiring...........................................................................................................5
1.7 Power Sequences.........................................................................................5
1.8 Troubleshooting ...........................................................................................6

User Manual Multi-Card Technology Reader – 13.56MHz, DesFire EV1 / EV2 and EM / HID
3
The Genie DFE-PROX-DUO is a multi-card technology reader in a sleek design.
1.1 Product Features
• Read 125KHz HID Prox and EM card and read full UID (56bits) or files content of
DesFire EV1/EV2 card, supports both 3DES and AES encryption, and reading
the Mifare sector at the same time Read mobile NFC
• Support on-site Reader Configuration Card to change certain parameters
• Tamper protection
• Front plate customisation and back lit design is available
• IP65 ingress protection
• Metal back plate allows the reader install on metal surface and back-to back
without affecting the read range
• Universal back plate allows the reader be installed on different size of gang box
• Reverse power protection
• All input and output signals are protected against static charges
• All inputs are DC12V protected
1.2 Product Dimensions
84.5mm 20.5mm
115.5mm

User Manual Multi-Card Technology Reader – 13.56MHz, DesFire EV1 / EV2 and EM / HID
4
1.3 Specification
1.4 Mounting
1. Install the metal plate on the wall with two or four screws, which depends on different
kinds of gang box being installed (1).
2. The cover shall clip on the upper edge (2) the push in the bottom part as show in
diagram (3).
3. Tighten the secure non-dropout screw, which located underneath of the reader to fix
the reader and the back plate (4), installation is completed.
Re-configure Window 5 seconds (Default) or Half an hour after power up
Reader Output Format CSN/UID 32bits, 34bits, 56bits (backward/forward), file
content reading for programmed ID
Wiegand Plus Width Different choices to fit with different controller’s requirements
Buzzer Control Reader & controller control (Default) or controller control only
LED/Back Lit Control Define different LED colour response base on LED input
Typical Read Range 2 – 3 cm
Reader Standard Output Wiegand (RS232 & RS485 (OSDP) (optional)
Wiring Distance 150m (22 AWG with shielded cable)
Operating Voltage DC10 – 15V
Operating Current 150mA (max)
Operating Temperature -30°C – 70°C
Operating Humidity 10% – 90%
Dimensions 115.5 × 84.5 × 20.5mm
Weight 210g

User Manual Multi-Card Technology Reader – 13.56MHz, DesFire EV1 / EV2 and EM / HID
5
1.5 Recommendation
1. Linear DC Power Supply.
2. 22AWG shielded cable, it’s required to do “one-point” ground. (As shown in the
diagram)
1.6 Wiring
1.7 Power Sequences
1. When reader is powered up, the Red back will flicker for 5 seconds. The reader will
beep once and the reader is in Ready mode.
2. Present the card. The Blue LED will flicker once, buzzer will beep once.
3. When card is present and read by the reader, blue back lit will flash once; and buzzer
will beep once as well. The card data will then transmit to the controller. After, weather
the back lit of the reader will remain ON or Flash or change to Green or Red colour, this
shall depend on the Green and Red LED inputs.
4. For number pad reader, when a number is pressed and successfully detected, the back
lit under the number will flash 1 time and the buzzer will beep once. The number being
pressed will burst out by default (4 bits burst).

User Manual Multi-Card Technology Reader – 13.56MHz, DesFire EV1 / EV2 and EM / HID
6
1.8 Troubleshooting
No response when power up
Discount the power and confirm that the power supply cable is correctly connected (See
“Wiring” above).
Check the input voltage is sufficient (See “Specifications” above).
Auto Restart
Check the input voltage is sufficient (See “Specifications” above).
Cannot read card number correctly
Check the format setting on the controller if it is the same as the card format. Use ap-
proved card (known format and Facility Code) to test.
Check if the shield cable is correctly connected to Classis Ground at ONE point only.
Reader beeps but No card data info
Check if data 0 & data 1 cable is correctly connected (See “Wiring” above).
Check the input voltage at the card reader end is correct (See “Specifications” above).
Buzzer error
Check if the buzzer cable is correctly connected (See “Wiring” above).
Back lit error
Check the Led cable is correctly connected (See “Wiring” above).
Use Default Configuration Card to set it back to normal.
Keypad no response
Power off reader for 5 seconds and power on again

Sales [phone]
Enquiries [email protected]o.uk
Website www.genieproducts.co.uk