Genie POE-INJ01S User manual

Quick Start Guide
Please read these instructions carefully before operating the unit
and keep for further reference. All the examples and pictures used
here are for reference only. The contents of this manual are subject
to change without notice.
PoE Single Port Passive
Injector - 30W
POE-INJ01S

Quick Start Guide PoE Single Port Passive Injector - 30W
2
The Genie POE-INJ01S is a power over ethernet mid-span injector that offers
an easy, fast and cost effective solution for powering PoE devices such as IP
network cameras. Power and data are combined on a single cable eliminating the
need for separate cables for data and power, reducing installation costs and time.
Features
• PoE+ power supply standard, output power consumption up to 30W
• IEEE 802.3af/at IEEE 802.3 10Base-T/100Base-TX/IEEE802.3ab 1000Base-T
• 6KV lightning protection, 8KV ESD
• Higher conversion efficiency (90%), Lower heat radiation
• No fan, no noise, dustproof
• LED’s indicate operation status
Specifications
Interface
Input Voltage AC100V~AC240V
Data Input 1 x RJ45
PoE Output 1 x RJ45
PoE
PoE Power Supply Type End-span
PoE Power Output DC 54V/30 watts
Output Ripple <5%
Power Pin Assignment Pair 1/2(+),3/6(-)
Ethernet Port
Communication Port 1 x RJ45 Input
Transmission Rate 10/100/1000Mbps
Transmission Medium Cat5/5e/6 Cable
Distance 100m (Max.)
Status Power LED 1 (Red)
PoE LED 1 (Orange)
Others
Surge Protection
PoE Power: 1KV(Differential Mode), 2KV(Common Mode)
1.2/50us 8/20us
Ethernet: 2KV(Differential Mode), 6KV(Common Mode)
10/7000us
ESD
1a Contact Discharge Level 3
1b Air Discharge Level 3
Per: IEC61000–4–2
Working Temperature -10 C~55 C
Storage Temperature -40 C~85 C
Humidity
(Non-Condensing) 0~90%
Dimensions 160 × 64 × 60 mm

Quick Start Guide PoE Single Port Passive Injector - 30W
3
LED Indicators
Diagram
Application
Monitor
NVR
POE-INJ01S
Cat5/5e/6 Cable
Ethernet Switch
PoE Camera
Input power indicator Output PoE indicator
The transmission distance depends on the signal source and cable quality, standard
Cat5e/6 cable is strongly suggested for reaching the maximum transmission distance.

Quick Start Guide PoE Single Port Passive Injector - 30W
4
Installation Steps
Please check the following package contents, if you find the a missing item,
please contact your local dealer.
1 x PoE Injector 1pc
1x AC Power Cable 1pc
1x Power Buckle 1pc
1x User Manual 1pc
1. Turn off the system’s power before the installation.
2. The PoE Output port of this injector is connected with PoE IP Camera.
3. The Data Input of this injector is connected with switch of no PoE fuction.
4. Please connect PoE Injector with AC cable.
5. Please examine and power the system.
RJ45 Making Method
Instruments to be used: wire crimper, network tester. Wire sequence of RJ45
plug should conform with EIA/TIA568A or 568B.
1. Please remove 2cm long the insulating layer, and bar the 4 pairs UTP cable.
2. Separate the 4 pairs UTP cable and straighten them.
3. Line up the 8 pieces of cables per EIA/TIA 568A or 568B.
4. Cut off the cables to leave 1.5cm bare wire.
5. Plug 8 cables into RJ45 plug, make sure each cable is in each pin.
6. Use the wire crimper to crimp it.
7. Repeat above 5 steps to make the another end.
8. Using network tester to test the cable whether is working.
Note:
• When choose RJ-45 make sure if one end is EIA/TIA568A,the other end
should also be EIA/TIA568A.
• When choose RJ-45 make sure if one end is EIA/TIA568B,the other end
should also be EIA/TIA568B.
Pin Colour Pin Colour

Quick Start Guide PoE Single Port Passive Injector - 30W
5
Troubleshooting
If any trouble in installation, please follow these steps:
• Please make sure you have followed the instruction to install the device.
• Please confirm if the RJ45 cable order is in accordance with the EIA/TIA 568A or
568B industry standard.
• The power supply of PoE port is no more than 30W, please do not connect the
network device whose power consumption is over 30W.
• Please replace a failure device with a proper one to check if the device is broken.
• If the problem still exists, please contact the local dealer.