Genie LM215 User manual

1
WARNING/CAUTION …............................................................................ 2
WARNING/CAUTION ……....................................................................... 2
FCC NOTICE ................................................................................ 2
CAUTION ................................................................................. 2
Important Safety Instructions ...................................................................... 3
Basic Instruction ............................................................................. 4
Equipment Sub-Assembly ...................................................................... 4
The best Resolution ........................................................................... 4
Input Voltage ............................................................................ 4
Keys Functions .......................................................................... 4
Connections .......................................................................... 5
On Screen Display (OSD) .......................................................................... 6
Menu Options ......................................................................... 6
Main Menu .......................................................................... 6
Explanation of Individual Options ............................................................. 6
Specification ......................................................................... 9
Compatible Resolutions ......................................................................... 9
Specification ......................................................................... 9
Contents

2
Class B Digital Device
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate frequency energy, and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.
Changes or modification not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Do not attempt to modify this product in any way without written authorisation from the
dealer. Unauthorised modification could void the user’s authority to operate this
products
To prevent fire or shock hazards, do not expose this product to rain or moisture.
Warning/Caution
TO REDUCE THE RISK OF ELECTRONIC SHOCK.
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL
The lightning flash with arrowhead symbol,within an
equilateral triangle, is intended to alert the user to presence
of uninsulated dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons
The exclamation point an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing )instructions in the literature
accompanying the appliance.
FCC NOTICE
Caution

3
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions in a safe place for future reference.
3. Heed all cautions and safety warnings.
4. Follow all instructions.
5. Do not use this product near water.
6. Clean only with a dry and soft lint free cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat register, stoves, or
any other apparatus (including amplifiers) that produces heat.
9. Do not defeat the safety purposes of a polarised or grounding –type plug. A
polarised plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched; particularly at the outlet
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the stand or bracket specified by the manufacturer, or sold with the
product.
13. Unplug this product during lightning storms or when unused for long periods of
time
14. Refer all servicing and repairs to qualified service personnel.
15. Do not expose this product to water or other liquids.

4
Basic Instructions
Equipment Sub-Assembly
Please check your monitor package includes the following:
Input Voltage
AC 100 - 240V ~ 50 / 60 Hz (Please check the label on the rear of the product)
Power Indicator Light
Indicator
Mode
No Light
Power OFF
Green Light
Working Normally
Green Flashing Light
No Input Signal
Keys Functions
5 Key Models
7 Key Models
Key
Function
Key
Function
①MENU
Show OSD Menu
Select Function
①MENU
Show OSD Menu
Select Function
②DOWN
Move Icon Down
Decrease Value
②DOWN
Move Icon Down
Decrease Value
③UP
Move Icon Up
Increase Value
③UP
Move Icon Up
Increase value
④EXIT
Back to Last Menu
Auto Adjust
④EXIT
Back to Last Menu
Auto Adjust
⑤
Turn Monitor ON / OFF
⑤SCALE
Change Ratio
(Wide or Normal)
⑥SOURCE
Display or Change Input
Signal
⑦
Turn Monitor ON / OFF

5
Connecting Cables
Power Input
Audio Input
Signal Input
AC input
Connect the power cord for your monitor to the AC IN port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
Use a connection appropriate for your computer.
VGA Input
Using the D-Sub (Analogue) connector on the video card.
DVI Input
Transmits digital video signals to the monitor. Connect the monitor using a DVI cable.
HDMI Connection
Transmits the digital video and audio signals from your PC and A/V Devices to the monitor.
Connect your PC and AV device to the monitor with the HDMI cable.
CONNECTIONS

6
Main Menu
1. Colour Adjust
2. Image Adjust
3. Colour Temperature
4. Tools
5. Language
6. Music
Explanation of Individual Options
1. Colour Adjustment
1.1 Brightness Adjustment:
This option adjusts the display brightness. Use the Up and Down buttons to increase
or decrease the brightness setting.
1.2. Contrast Adjustment
This option adjusts the amount of difference between white and black values. Use the
Up and Down buttons to increase or decrease the contrast setting.
1.3 DCR Function
Press MENU to show the main menu choices. Select DCR, press Up or Down to
select ON or OFF. Press MENU to open or close DCR function.
2. Image Adjust
2.1 Horizontal Position Adjustment:
This selection adjusts the horizontal positon of the video on the display. This
function is only available in VGA mode. Use the Up and Down buttons to move the
video display area position.
On Screen Display (OSD)
Menu Options

7
2.2 Vertical Position Adjustment:
This selection adjusts the vertical position of the video on the display. This function is
only available in VGA mode. Use the Up and Down buttons to move the video display
area position.
2.3 Phase Adjustment:
Press MENU to show main menu choices. Select ADJUSTMENT, and then press Up
or Down to start pixel sampling by phase to improve stabilisation.
2.4 Clock Adjustment
Press MENU to show main menu choices. Select FREQUENCY adjustment and, then
press Up or Down to adjust clock image display to track stability.
2.5 Sharpness Function
Press MENU to show main menu choices. Select SHARPNESS adjustment, and then
press Up or Down to select the value, and then press Menu to change the sharpness
of image.
3. Colour Temperature Adjustment
This selection changes the amounts of red, green and blue present in the image.
Warm mode increases the amount of red, cool mode increases the amount of blue
and user mode allows you to make your own adjustments to the red, green and blue
levels.
4. Tools
4.1 OSD H-Position Adjustment.
This selection will change the horizontal position of the On Screen Display Menu
(OSD). Use the Up and Down buttons to change the position (left to right).
4.2 OSD V-position adjustment.
This selection will change the vertical position of the On Screen Display Menu (OSD).
Use the Up and Down buttons to move the display (up and down).
4.3 OSD Timer
This selection adjusts the OSD menu display time on the screen.

8
4.4Translucence
This selection adjusts the OSD menu transparency on the screen.
5. OSD Language Setting
This selection allows you to select the language you want the menu to appear in.
Select from English, Spanish, French, Italian, German or Korean.
(Depending on the model, additional languages may be present).
6. MISC
6.1 Auto Configuration
This selection automatically adjusts your image setting to the best viewing.
6.2 Auto Colour
This selection will automatically adjust your color setting to the best viewing.
6.3 Factory Reset
This selection resets the monitor to factory default settings.

9
Signal Input
VGA, DVI, HDMI
Audio In
2x 2W
H-Frequency
30~80 KHz
V-Frequency
60~75 Hz
Temperature
Storage Temp:-20°to 60°
Operation Temp：0℃to 40℃
Humidity
Operation：10% to 85% RH
Specification
Compatible Resolutions
Specification