Genie SDI07HY User manual

MODEL: SDI07HY
Hybrid Portable Test Monitor
User Manual

Hybrid Portable Test Monitor 3
Precautions
• Always handle the unit with care to avoid damaging the LCD display panel. Damage caused by
physical shocks is not covered by the product warranty.
• Avoidgettingngerprintsonthescreen.Tocleanthescreen,wipeitwithaclean,softanddrytowel,
beingcarefulnottodamagetheLCDdisplaypanel.
• Toreducetheriskofreorelectricshock,donotexposetheLCDtorainormoisture.
• Donotconnectpowertothevideoinput/outputports.Itwillcauseamalfunction.
• Onlyusetheapprovedbatterychargerincludedinthepackage–aremaybecausedifanon
unapprovedchargerisused(iftheredLEDickersduringrecharging,requestaftersalesservice).
• Thebuilt-inLi-Polymerbattery(11.1V/2200mA)hasasixmonthwarranty-effectivefromthe
purchasedate.Donotuseanyanothertypeofbatteryonthisportablemonitorasitmaycauseare
orexplosion.
• Thebatterycouldbedamagedifashortcircuitispresentattheconnectingport,orifthepolarityofthe
power cable is reversed.
• Whensupplyingpowertothecameraviathetestmonitor,alwaysusetheenclosedpowerharness
(DCJack).
• Whensupplyingpower,connectthepowercabletothecameraandthenapplypower.Otherwise,a
shortcircuitmightbeinducedwhichautomaticallyswitchestheunitofftoprotectthebattery.Ifashort
isproduced,turnthemonitoroff,removeandre-insertthepowerharness(DCJack).Thenturnthe
unit on again.
• KeeptheunitinsidethecarrybagtoprotecttheLCDscreenfromscratches.
• Donotputthemonitoron,ornear,anythingelectricallyconductiveorexposetheunittorainor
moisture.
• Immediatelyswitchtheproductoffifitemitssmoke,makesanabnormalnoiseoremitsstrange
odours.
• Iftheunitisnotworkingproperly,pleasecontactyourdistributor.Pleasedonotdisassembletheunit
yourselfasitwillinvalidatethewarranty.

Hybrid Portable Test Monitor
4
1. Introduction
1-1. Overview
TheSD107HYisamulti-functionalAnalogue/HD-SDI/HDMIportabletestmonitor.Itcanbeusedfor
variouspurposes,includingcheckingvideosignals,thecablingstatus(hasabuilt-inHDSDI/Analogue
videosignallevelmeter,adjustingcameraangleofviewandfocusing,supplyingpowertocamera,
controlling a speed dome camera and generating color pattern to the monitor.
1-2. Features
• 7-InchWideTFT-LCDDigitalLEDBacklitPanel
• Variousinputs:HD-SDI(3G),HDMI(1080p60),VGA(1600x1200),CVBS
• VariousOutputs:HD-SDI(3G,LoopThrough),CVBS(LoopThrough)
• HD-SDI and Analogue Video Signal Level Meter
• HD-SDI Focus Meter
• PTZcontrolviaRS-485communicationforspeeddomecameras
• Coaxialcommunication(UptheCoax).ControlscameraOSDmenu/PTZovercoaxcable(Max.800m)
• Supplypowertothecamera(DC12V/500mA)
• HD-SDI,HDMIAudioOutput(Optional)
• Leather bag and strap
• Li-polymerbattery(6~8hoursofuse)
1-3. Applications
• Displayvideosignalsoradjustcameraangles.
• Check the cable status and/or DVR.
• Checkspeeddomecameras,PTZcamerastatusorcontrolPTZ.
• ControltheOSDmenuofacamerawhichsupportscoaxcommunication.
• CheckHD-SDI,HDMISignals.
• Check the distance at which HD-SDI Repeaters & Receivers should be installed.
• Check DVR VGA outputs
• TestandinstallPOC(PoweroverCoax)Camera(HD-SDI,CVBS)(Optional)
Main Unit Leather Bag
& Shoulder Strap
Accessories
Charger &
Power Cord
Power Harness
2. Components


Hybrid Portable Test Monitor 5
1 2 3 4 5 6 789 10
No. Marking Function
12V ChargetheBuilt-InLi-PolymerBattery(withIncludedCharger)
or,SupplyPowertotheCamera(DC12V/500mA)viaPower
Harness.
RS-485 RS-485CommunicationforPTZReceiverandSpeedDome
Camera
HDMI INPUT HDMISignalInput(Max.1920x1080p60Hz)
HD-SDI INPUT HD-SDISignalInput(Max.Resolution:~3G)PowerOutput
(WhenUsingPowerOverCoaxFeature)
OUTPUT HD-SDISignalOutput(LoopThrough)
VGA INPUT UXGAInput(Max.Resolution:1600x1200)
VIDEO
TERM With Loop Through Output: HI-Z Position
INPUT CVBSVideoSignalInputCoaxialCommunication:PTZReceiver
or Speed Dome Camera Power Output (When Using Power
OverCoaxFeature)
OUTPUT CVBSVideoSignalOutput(LoopThrough)
OutputsFullColourBar(PatternGenerator)
POWER PowerSwitch(ON/OFF)
3. Product Parts and Peripheral Device Connection
3-1. Part Names and Functions
1
2
3
4
5
6
7
8
9
10

Hybrid Portable Test Monitor
6
3-1-2. Buttons for Each of the Functions
VP : Link Check
16:9
1920X1080p60
HDMI
16:9
1920X1080p60
S.LVL: 90% Good
FOCUS: 100 / 100
1
1
2
2
54 3
Level Meter Indicator
• S.LVL:IndicatesthevideosignallevelofHD-SDIasapercentage.
• FOCUS:IndicatesthefocusingstatusforHD-SDIvideoasapercentage.
• A.LEVEL:Indicatesthebrightnesslevelofthevideo(Amplitude/Synclevel)asapercentage
• F.LEVEL:Indicatesthecolourlevelofthevideo(Frequency/Burstlevel)asapercentage.
Button Camera Menu RS-485 & Coax
Mode
Angle Guide Video Input
MODE PTZ&OSD Mode
Switch
Source Change
EXIT Operate in PTZ
Mode
Angle Mode Out Hot Key
(Zoomin)
MENU Operate in OSD
Mode
Menu ON
ESC Operate in OSD
Mode
Menu OFF
Multi-Way
Key
Up,Down,
Right,Left
Pan/Tilt/Zoom/Fo-
cus
Up,Down,
Right,Left
ENTER
Key
ENTER SelectBar Long: VP ON/
OFF
MenuOperationButtons

Hybrid Portable Test Monitor 7
5
4
3Video Status
• InputMode:HD-SDI,HDMI,VGA,CVBS
• DisplayMode:4:3,Full(16:10),16:9,Zoom1,Zoom2
• InputResolution:1920x1080p60,NTSC,PAL
BatteryStatus
• Therearesevenstepsindicatingbatterystatus.090%070%050%
POC(PowerOverCoax)deviceconnectionindicator.
3-1-2-1. Level Meter Indicator
HD-SDI Level Meter
• S. Level:IndicatesHD-SDIsignalsasapercentage.Thecloserto100%,thebetterthequalityofthe
video; and the lowest Video level is 27%.

Hybrid Portable Test Monitor
8
CVBSLevelMeter
• A. Level:Indicatesthebrightnessofthevideo(Amplitude/Synclevel)asapercentage.Thecloserto
100%,thebetterthequalityofthevideo.WhentheA.Level%isunder100%,itindicatesthevideo
signals are decreased and the brightness is reduced.
• F. Level:Indicatesthecolourlevelofthevideo(Frequency/Burstlevel)asapercentage.Thecloserto
100%,thebetterthequalityofthevideocolourandtheresolution.
• ThevideolevelmeterindicatesthesyncandburstlevelofCVBSvideosignalsinA.LevelandF.Level
respectively.
FocusMeterforHD-SDICameraandFocusMeter
• Focus Meter: Indicates the HD-SDI or Analogue Camera Focus as a percentage.
• Showsthefocuslevel(Min.20%toMax.255%)andoutputshighfrequencysoundstothespeaker
(Optional),dependingonthelevel.

Hybrid Portable Test Monitor 9
3-2. Connection Diagram
※Onlyusetheincludedpowerharnesscablewhensupplyingpowertoacamera.
3-2-1. HD-SDI Input
• ConnecttoHD-SDIcamera/outputthepowertocamerausingpowerovercoaxfeature.(Inputdata
bitrate:~3G)
• Outputspower(DC24V)toHD-SDIVP(Video+Power)cameraorHD-SDIVPdevice
3-2-2. HD-SDI Loop through Output
•OutputtheHD-SDIsignalinputfromtheHD-SDIcamera(Outputdatabitrate:~3G)
3-2-3. Analogue Video Input
• Connect to Analogue Camera
• Outputthepower(DC12V/500mA)tocamerausingpowerovercoaxfeature.
• UsingCoaxcommunicationfeature(Coaxitron),itispossibletocontrolthecameraOSDmenuora
PTZSpeedDomecameraviacoaxialcable.
3-2-4. Analogue Video Loop Through Output & Pattern Signal Output
• WhenPatternOutisOFF,V.OUTportoutputsthevideoreceivedfromAnaloguecamera.
• SelectPatternOutON,V.OUTportoutputsFullColourBartocheckthewiringstatus,monitor,DVR,
etc.
3-2-3. VGA Input
• ConnecttoDVRorComputerandUXGAissupportedatmaximumresolution;higherresolutionsmay
not be displayed normally.
3-2-7. HDMI Input
• ConnecttoDVR,ComputerorotherdevicewhichoutputsHDMIsignal.(Resolution:~1080p60Hz)

Hybrid Portable Test Monitor
10
3-2-4. PTZ & OSD Control Through RS-485
• ConnecttoPTZReceiverand/orSpeedDomeCameraasacontroller.Also,connecttocontrolleras
aPTZreceivertocheckifthecontrolleroutputsdataaccurately.
※Powerovercoaxfeature(Video+Power)forHD-SDI&AnalogueVPcameraandVP
transmission devices.
• UsingthePowerOverCoaxfeatureoftheHybridTestmonitor,it’spossibletosupplypowertoVP
(Video+power)analogueandHD-SDIcamerasviacoaxialcable.
• POC(PowerOverCoax)featureforHD-SDIVPcamera(Optional):Whenit’snecessaryto
usethePowerPOC(PowerOverCoax)feature,forinstallationandmaintenanceofaHD-SDIVP
cameraorotherHD-SDIVPTransmissionproduct,pressandholdthe‘Enter’keyfor3secondsor
more,andtheVPfeatureisactivated;afterdetectingifthedeviceautomaticallysupportsthePOC
feature.
• PowerOverCoaxfeatureforAnalogueVPcamera(Optional):Whenit’snecessarytousethe
PowerPOC(PowerOverCoax)feature,forinstallationandmaintenanceofananalogueVPcamera
orotherVPTransmissionproduct,pressandholdthe‘Enter’keyfor3secondsormore,andtheVP
featureisactivated;afterdetectingifthedeviceautomaticallysupportsthePOCfeature.
4. Menu Setting
4-1. MENU Mode
4-1-1. SELECT MENU
• PressMENUButtonandmainmenuisdisplayed,asshownbelow.
• PressthedirectionalbuttonstomoveUp,Down,RightorLeft.
Themenumodeisautomaticallyswitchedoffifyoudon’tpressanybuttonsforafewminutes.





4-1-1-1. PICTURE SET


Hybrid Portable Test Monitor 11
• Contrast:Toadjustthecontrastrange(0~100steps)
• Brightness:Toadjustthebrightness(0~100steps)
• Hue:Toadjustthecolour(0~100steps)
• Saturation:Toadjustthechroma(0~100steps)
• Picture Mode: Standard > Movie > Vivid > User
Thevalueofeachmodechangesautomatically
• Scale:Toadjustthescreenratio(Full>4:3>Zoom1>Zoom2>16:9)
• Reverse:ToreversetheupperandlowersidesoftheLCDscreen.
4-1-1-2. ANGLE MODE
Indicationlines:Toadjusttheviewinganglesbasedonaspecicarea.


• SelectingANGLEMODEdisplaysagreenboxandthecameraanglezoneindicationlines.
• PresstheSETMENUbuttontoselectthesizeofthegreenbox.PresstheSETMENUbuttonagain
andselectthesidelinesoftheboxyouwanttoadjust,andpressthe///buttonstoset
thepositionofeachline.
• ToexitANGLEMODE,presstheEXITKEY.




4-1-1-3.RS485&COAXMODE(PTZ/OSDControl)
• MODE:InRS-485TxandCOAXmodeyoucancontrolthePTZ&CameraOSD.InRx.mode,it
receivesthePTZcontroldata(asHEXvalues)anddisplaysthedataonthemonitor.InAnalyser
mode,itanalysestheprotocolsreceivedthroughtheRS-485portanddisplaystheHEXvalueand
command.
• PROTOCOL:Toselecttheprotocoloftheequipmentwhichyouwanttocontrol.
• ADDRESS:Toselecttheaddressoftheequipmentwhichyouwanttocontrol.
※InCOAXmode,youcancontrolthecameraregardlessoftheaddress
• BAUDRATE:Toselectthecommunicationspeed(2400,4800,9600,19200,38400).
※InCOAXmode,youcancontrolthecameraregardlessofthebaudrate
• START:Tostartcontrollingthedeviceaftersettingalltheabovemenus.
• EXIT:ToexitfromMENUMODE

Hybrid Portable Test Monitor
12
※Built-inProtocols:
No. Company Protocol Product Model
01 DONGYANG
UNITECH
(OSD)
D-MAX DSC-300S/270S/230S
Series(HighSpeedPTZDomeCamera)
DOH-240S Series
(SpeedPTZDomeCamera)
DPC-200
(MiniPTZDomecamera)
DRX-500,DRX-502A(CCTVPTZreceiver)
02 DONGYANG
ELECTRONICS
DY-255RXC DY-255RXC
03 FINESYSTEM FineSystem CRR-1600i/s
04 INTER-M VRX-2201 VRX-2201
05 HONEYWELL(OSD) Honeywell HRX-2000,ScanDome-Ⅱ
06 LGMultiX(OSD) LG MultiX LPTEP551PS/
EI551PS/OS551HQ/OI551HQ/OI511HQ
07 LG LPT-A100L LG LPT-A100 LPT-A100L
08 PANASONIC(OSD) PanasonicC CS600,CS650,CS564,CS85X,…
09 PANASONIC PanasonicN CS564CS854/A,…
10 PELCO(OSD) Pelco-D GenieASD,GenieNSD
11 PELCO(OSD) Pelco-P GenieASD,GenieNSD
12 SAMSUNG
ELECTRONICS
(OSD)
Samsung SCC-641/3/07,…,SCC-64xSeries
13 SAMSUNG
TECHWIN(OSD)
Techwin SPD-xxxxSeries
14 SUNGJIN Sungjin RECEIVER/MPU
15 SYSMANIA Sysmania ORX-1000
16 VICON Vicon Stn V1311RB,V1310RB,V1200R-LM,etc.receivers
17 VICON ViconExt Surveyor Dome Series
18 IKEGAMI Ikegami35 PCS-35
19 IKEGAMI Ikegami358 PCS-358
20 NEWBORN
HIGHTECH
NEWBORN
21 TOKINA TOKINA DMP
22 ERNITEC(OSD) ERNA BDR-51x,BDR-55x,BDR-575,ICU
23 BOSCH BoschOSRD Receiver/Drivers,G1,G2,G3,VEZ,andG4Series
AutoDomes
24 GSPSYSTEMS CYBERSCAN1
25 HITRON FastraxII FastraxII(HID-2404)
26 YUJINSYSTEMS YujinSys. EPT-5000S/6000S
27 DYNACOLOR DSCP Dyna. DSCP dynacolorDH801,DH701andDH600
28 LADON Ladon
29 HANIL STM MCU-1200N MCU-1200N,1400N,1500N
30 LILIN_MLP2 LILIN_MLP2
31 LILIN_FastDome LILIN Fast
32 AMERICAN
DYNAMICS
AD SpdDome
Theprotocolsmarkedwith‘(OSD)’areavailabletocontrollingCAMERAOSDMenu.

Hybrid Portable Test Monitor 13
4-1-1-4-1.RS-485(TX)
• Displaysthecurrentsettingmodeatthetopofthescreen.
• PressSETKEYinMULTIWAYKEYselectiontoselectPAN/TILTorZOOM/FOCUSmode.
-RED:P.T.ZMODE-BLUE:OSDMODE
• PresstheModeKEYtoselectCAMERAOSDcontrolmode.
• PresstheMENUKEYtocontrolCAMERAOSDandpresstheESCKEYtoexitOSDMENU.
• IncaseofBOX/DOMECamera,holdtheENTERKEYtoselecttheOSDMenu.
• PressEXITKEYtogotothepreviousmode
• (inCAMERAOSDmode,switchtoPAN/TILTmoderst,inordertoexit).
• Press///buttonsfollowingtheOSDguidanceonthescreen.
※Caution
• TheHybridTestmonitorhastwodifferentPELCO-DProtocols,whicharePELCO-DPROTOCOL,
PELCO(CNB).
• ForPELCO-DPROTOCOL,itispossibletoenterthecameraOSDmenubyusingMENUkey.
(SETPRESETCOMMAND)
• ForPELCO(CNB)PROTOCOL,itispossibletoenterthecameraOSDmenubyusingMENUkey
(GotoPRESET)orESCkey(RunPRESET)
• Dependingonthecameramanufacturer,thecommandtoenterthecameraOSDMenuisdifferent.




4-1-1-4-2. RX
• Displaysthecurrentsettingmodeatthetopofthescreen.
• DisplaystheconnectionstatusoftheRS-485lineindicatedbyaHEXvalue.
• ThereceiveddataviatheRS-485portisdisplayedasamaximumin8linesinbytes(16byte).
• Whenthedataismorethan128byte,it’sclearedoutautomatically.Youcanalsoclearitout
temporarily,usingtheESCbutton.
• Togotothepreviousmenu,presstheEXITbutton.

Hybrid Portable Test Monitor
14
4-1-1-4-3.COAX [UP THE COAX] Control
• Displaysthecurrentsettingmodeatthetopofthescreen.
• PresstheSETKEYinMULTIWAYKEYselectiontoselectPAN/TILTmodeorZOOM/FOCUSmode.
-RED:P.T.ZMODE-BLUE:OSDMODE
• PresstheModeKEYtoselecttheCAMERAOSDcontrolmode.
• PresstheMENUKEYtocontroltheCAMERAOSD,andtheESCKEYtoexitOSDMENU.
ForBOX/DOMECameras,HoldtheENTERKEYtoselectOSDMenu
• PresstheEXITKEYtogotothepreviousmode.InCAMERAOSDmode,switchtoPAN/TILTmoderst
inordertoexit.
• Press///buttonsfollowingtheOSDguidanceonthescreen.
• Listofcontrollablemodels




No. Company Protocol Product Model
01 Samsung Techwin PELCO-C All models to support
COAXcommunication(WINNER5)
02 Pelco PELCO-C All models to support
COAX communication
03 Dongyang Unitech PELCO-C All models to support
COAXcommunication(PIXIM)
04 SamsungE A1 All models to support
COAX communication
※PELCO-CPROTOCOLinHybridTestmonitoriscompatiblewithalltheproductmodelsabove.
Also,thisproductcancontrolCOAXinaremotesidethroughtheautomaticNTSC/PAL
recognitionwithoutanyset-up.
4-1-1-4-4. ANALYSER
• UsingAnalysermode,thetestmonitorrecognisesthereceiveddatapacketanddisplaystheaddress
and command.
• Addr: Show the address.
• Cmd: Show the command
• Packet:ShowtheHexcodeofthereceiveddata.

Hybrid Portable Test Monitor 15
4-1-1-5. PATTERN SET
• BasicallyoutputstheinputsignalsthroughtheVideoOutBNC.Butifyouselect“ON”ontheCVBS
Outinthepatternsetmenu,theselectedpatternisoutputfromtheVideoOutBNC.
• Itispossibletoselectoneoftenpatterntypes.

4-1-1-6. LEVEL METER & FOCUS METER
• CVBSLevelMetercanbeON/OFF.
• HD-SDI Level Meter can be ON/OFF.
• HD-SDI Focus Meter can be ON/OFF.

Hybrid Portable Test Monitor
16
• Language:KOR/ENG/JAP
• OSD Dwell Time: To set the time to turn the monitor menu OFF
• BACKLIGHT:ToadjustthebrightnessoftheLEDMonitor.
• Setting Initialisation: To initialise all settings.
• Version: To display the product Firmware version and the date.
4-1-1-7. SYSTEM SET
• To set the System

Hybrid Portable Test Monitor 17
5.Specication
SD107HYHybridTestMonitor
LCD DISPLAYRESOLUTION 1280X(RGB)X800
SIZE 6.95inch(Diagonal)
PIXELPITCH 0.117mm(H)X0.177mm(V)
BRIGHTNESS(cd) Min.:340,Nor.:400
CONTRAST RATIO Min.:600,Nor.:800
Viewing
Angle
Horizontal 89°
Vertical 89°
RESPONSE(ms) 11
VIDEO INPUT HDMI ~1080p60
HD-SDI ~3GPoCOutput(DC24V)
CVBS NTSC/PAL1.0Vp-pPoCOutput(DC24V)
XVGA Max.1600x1200,60Hz
OUTPUT CVBS PATTERNON ColourBar
PATTERN
OFF
Loop Through Output
VIDEOOUT NTSC/PAL1.0Vp-p(75Ω)
HDSDI VIDEOOUT ~3G,LOOPTHROUGH
Indicationrangefor
CVBS
video signal level
ALEVEL 10~118%
FLEVEL 20~120%
ERRORRATE ±2%
RANGEFOR
HD-SDI SIGNAL
LEVEL
SDILEVEL 10~100%
FOCUSLEVEL 10~100%
ERRORRATE -
CONNECTPORT HDMI INPUT HDMI C Type F
HD-SDI INPUT BNC-F
HD-SDI OUTPUT BNC-F
VGA INPUT D-SUB15-PinRIGHTANGLETYPE
CVBSVIDEOINPUT BNC-F
CVBSVIDEOOUTPUT BNC-F
RS-485 Pan/Tilt/Zoom/Focus
Control
OSD Control
POWER INPUT DC12.6V(exclusiveAdapterincluded)
OUTPUT DC 12V
COLOUR Dark Grey
BATTERY 2xLi-Polymer:11.1V,2200mA(protection
circuitapplied)
POWER
CONSUMPTION
With HDMI input 6.5W
With HD-SDI input 7.5W
With VGA Input 6.5W
WithCVBSInput 6.5W
VP On Differentdependingoncamera
(DonotusePTZCameras)
TEMPERATURE 0℃~+50℃
HUMIDITY 0%~80%
WEIGHT SET:920g,BAG:640gTotal:1.6kg
DIMENSIONS(excludingthebag) 240.9(w)X153.4(h)X50(d)mm

GENIE CCTV LTD.
CCTVHouse,CityPark,Watchmead,WelwynGardenCity,Hertfordshire,AL7ILT
Tel:+44(0)1707330541Fax:+44(0)1707330543
www.geniecctv.com
Edition.GN-March2013