Genuwine Cellars Elite Kit Rack User manual

#6 Robertson Screws
(Square Head)
(QTY: 4)
#8 Robertson Screws
(Square Head)
(QTY: 4)
Angled Brackets
(QTY: 4)
We Recommend A
21 Gauge Nail Gun
(Use 21 gauge brand nails,
with appropiate air compressor
or electric nailer set to 80psi,
to prevent spliting)
Robertson
Screwdrivers #6 & #8
(Square Head)
750ml 6 COLUMN 1/2 HEIGHT RACK 750ml 9 COLUMN 1/2 HEIGHT RACK 750ml TASTING TABLE
1 - Left
Ladder 1034
(QTY: 1)
2 - Middle
Ladder 1034
(QTY: 5)
3 - Right
Ladder 1034
(QTY: 1)
4a - Front Spacer Bars 689
(QTY: 3)
4b - Back Spacer Bars 689
(QTY: 3)
5a - Counter Top 689
(QTY: 1)
5b - Counter Nosing 689
(QTY: 1)
6 - Base Mould 689
(QTY: 1)
Drywall Anchors
(QTY: 4)
ELITE KIT RACK ASSEMBLY INSTRUCTION
COMPONENTS
HARDWARE
TOOLS REQUIRED
Thank you for purchasing Elite Kit Rack by Genuwine Cellars. The following
instructions will help you assemble the 750ml COLUMN 1/2 HEIGHT RACK.
The same procedure can be applied to the following kits shown.
Please study the i structio s carefully prior to starti g the assembly.
The following tools are required (NOT INCLUDED):
The following hardware is included in all kits:
(QUANTITY WILL VARY, DEPENDING ON KIT.)
The following components are included in the 750ml COLUMN 1/2 HEIGHT RACK.
(COMPONENTS WILL VARY IN QUANTITY AND SIZE, DEPENDING ON KIT.)
IMPORTANT!
Always follow the manufacturer's
instructions on how to use the nail
gun, to prevent injury. Genuwine
Cellars is not liable for any injury
incurred while assembling the kit.

A
B
C
Front View
A
B
C
STEP
1
STEP
2
STEP
3
STEP
4
Starting from the back of the rack. Place the ladders on flat, soft
surface, so not to damage front of rack. Space the ladders
accordingly. (Note: E sure proper placeme t of ladders,
a d bottoms are all i same directio as show .)
From the bottom and working your way up, place the back spacer bars (4b) according to the
ladder notches. Make sure to carefully interlock the spacer bars to the ladders.
Once spacer bars are properly placed. Start from
the bottom of the rack, firmly apply pressure to lock
in the joint. Then apply two nails with a nail-gun, to
each joint. Remember to firmly lock in each joint.
While backs are still facing up, screw the angled brackets
to the back spacer bars as shown.
Front of ladder
(Note: Bigger otch is
bottom of ladders)
Back of ladder
Back
Flush
Firm Pressure
Firm Pressure
Brackets
Brackets
(Note: Bottom brackets
should be mou ted o
top of spacer bar,
i stead of u der eath)
Apply Nails
3
2
1
4b
Angled
Flat

D
Nosing Sample A
D
STEP
5
STEP
6
STEP
7
With the help of another person, turn the rack so the back is on the floor, and the front is
facing up. Starting from bottom up, place the front spacer bars (4a) according to the ladder
notches. Make sure to carefully interlock the spacer bars to the ladders.
From the front and bottom of the rack, firmly apply
pressure to lock in the joint. Then apply two
nails with a nail-gun, to each joint. Remember
to firmly lock in each joint.
To apply the counter top (5a), stand the rack upright. Flush the counter top to the back, left and
right side of the rack. Apply pressure to the top of the counter. Nailing from underneath, apply
nails through the front and back spacer bars, into the counter top.
STEP
8To finish the 750ml 1/2 height rack, apply the base mould ( ) as shown. Applying counter top
nosing (5b) there are 2 options. Option A, or nosing can be left off.
Apply Nails
Firm Pressure
Firm Pressure
Apply Nail Front
and Back
Apply Pressure
on Top
Counter Nosing
4a
5a
5b