GEO-Laser UL-89L User manual

Algebraic sign
Status symbols
= Initialising
Inclination adjustment
Inclination adjustment finished,
power saving mode
T = Kick guard active (see 3.3)
T = Blinks after jerky movement,
laser beam off
Power supply indicator
Laser beam symbols:
Laser blinks when levelling
Laser off when levelling
Laser + rotor off with FB-10
Percent sign (see 3.5)
Inclination value, x/y axis resp. OFF
Rotor speed (8 = 800 rpm)
< 1/4 < 1/2 < 3/4 >3/4
Keep the button pressed until the adjustment menu is shown.
5
=
factory defaults
factory defaults
actory defaults
on. When setting the inclination, + or - can be selected and
then inverted.
= off (factory default)
Please note: Setting only possible in a range of ± 5 %.
3.10 Laser Power
The laser power can be regulated in 5 steps from approx. 0.5 mW
to < 2.6 mW.
Up to a range of approx. 200 m step 2 = < 1 mW is recommended.
= < 2.6 mW ( )
3.11 Operation Mode Laser Beam
Laser beam and laser beam symbol at the operating mode
=display blink when levelling ( ).
= Laser beam is off when levelling.
However the symbol blinks at the operating mode display.
3.12 F
= All set to factory defaults.
3.13 Service/Workshop Notice
First off all a phone no. for service/help appears. Then authorized
personnel can put in a numerical code to come to the adjustment
mode.
Select Letter
The selected letter blinks.
Change Settings
Back to Operating Display
or
or
Menu
OK
= Select Indication of Factory Defaults
6. Locking Automatic (see 19.)
in the Y axis in combination with the locking receiver FE-53. Laser and receiver
correspond via radio circuit.
By pressing the button of laser or receiver the laser startsto search for the receiver.
As soon as the rotating laser beam hits the receiver,it is directed to the center and
fixed there.
6.1 Operation
Set-up laser and receiver over the line axis, switch on
both, switch off Y axis and set the rotor speed to 800
rpm. As soon as the radio control is connected, the
system startsto operate.
On the laser display an alternating direction arrow
appears and on the receiver the LEDs are blinking
alternately.
Accuracy: to +/- 0.5 mm/100 m.
The FE-53 can be mounted either on the left or on the right side of the laser.
Because of reasons of functionality,the keyboards of both devices must be on the
same side.
Scan mode
Radio control:
connected
connected and laser reception
disconnected
Direction arrow
Centre indicator
Rotor speed 8= 800 rpm
6.2 Display Locking Automatic (Horizontal Set-Up)
6.3 Scan Mode
It can be started either at receiver or at laser.After its activation the laser scans and
finds the receiver automatically.
Start scan at laser:
Menu
OK
3 x =
or =Scan starts.
The indicates the control direction on the display.
Sblinks
Note: A radio communication with the FE-53 is provided, indicated by the
symbol " " on the LCD display (see 1.9).
8.
8.1 Horizontal Light Plane ( )
Adjustment Checking
Set-up the laser upright and mark laser beam in the height of the required
measuring distance. Turn laser device on the tripod by 180°, mark once again. If
the adjustment is perfect, the first mark does not deviate from the second one. Turn
device by 90°, repeat this process.
VerticalSet-Up
8.2 Horizontal Plumb Beam ( /Pipe Laying)Horizontal Set-Up
8.3Adjustment
If the adjustment is incorrect, please contact your specialist dealer.
The laser can be adjusted in the field without having to open the device. For safety
reasons, however, adjustment should only be carried out by authorized
personnel. See the special adjustment instructions in this regard.
Pressing the arrow buttons briefly changes the inclination value by 0.001 %.
The value is changed with increasing speed if the button is kept pressed.
+= 2.4 X Inclination Setting to Zero
The inclination value is set to 0.000 % by pressing the two arrow buttons at
the same time.
Y Inclination Setting
(Verticalset-up)
or
or Direction Setting
(Horizontal set-up)
Y Inclination Setting to Zero or
Direction Centering
+= 2.7
Verticalset-up:
Horizontal set-up: Device is automatically centred in middle position.
The inclination value is set to 0.000 % by pressing the
arrow buttons at the same time.
2.8 Quick Setting
In addition to the respective arrow button also press the ON/OFF button.
After setting one of the two arrow buttons the laser beam symbol changes to an
arrow. It indicates the direction of movement and the current position. When end
position is reached, the laser beam and limitation symbol blink. The setting must
then be moved back within 2.5 minutes. If this is not done, the laser is switched off
automatically.
Grade swap: minus or plus
(to activate see 3.9)
or
3. Device Settings
= 2.6
= 2.9
3.1 Switch ON/OFF Automatic Levelling
:
=
These are the factory defaults. They are always activated when
switching-on the laser.
= utomatic self-levelling cutted out in X and Y axis.
:
= utomatic self-levelling swiched on in X axis.
These are the factory defaults. They are always activated when
switching-on the laser.
= Automatic self-levelling swiched off.
On the display appears OFF %.
= Settings unlocked (
=I
= Inclination and direction setting locked.
Now direction control is not possible.
Vertical Set-Up
Horizontal Set-Up
3.2 Sensitivity Setting (Wind/Vibration)
The self-levelling function corrects even the smallest deviation.
Additionally the laser beam and the laser beam symbol at the operating
mode display blink when the limit values of step 1 to 3 are exceeded,
i. e. by influence of wind and/or vibration.
1 = 0.005 % no effect
2 = 0.010 % weak effect( )
3 = 0.015 % stronger effect
3.3 Kick Guard (Automatic Laser Beam Cut-Out)
= Kickguard switched on. It is only active after 30 sec. Then a T appears
in front of the battery symbol at the operating mode display
This means the laser is switched offautomatically as a precautionary
measure in the event of a jerky movement (bump). The Tthen begins to
blink. The laser must be switched on again by pressing briefly the ON-
button and the positioning must be checked and corrected if necessary.
= F : Kick guard switched off.
3.4 Inclination value display in % or ‰
Select between % or ‰ indicator.
=
)
nclination setting locked.
Automatic levelling switched on.
A
On the display appears behind the Xand YOFF.
Now the X and Y axes can be selected and set by the arrow buttons.
A
factory defaults
actory defaults
When the automatic is switched off in X and Y axes, it is not possible to
activate the kick guard.
factory defaults
3.5 Lock Function only when Setting-up Horizontally
factory defaults .
.
3.6
=
=
3.9
Radio Control On/Off
Is required for the operation with the remote control FB-10 or locking
receiver FE-53/-61.
off (energy-saving mode)
on ( )
3.7 Laser Beam Modulation Mode
= Standard modulation for FE-61 ( )
=db
= Modulation off
= Flickering for LE-7x stationary beam
3.8 Monitoring of Locking Automatic
When using the locking receivers FE-53/-61 the automatic locking can be
monitored. The laser beam switches off when the laser or radio
contact is interruped for more than 3 min.
It can be switched on again by briefly pressing the laser ON button.
= off ( )
=on
factory defaults
factory defaults
factory defaults
Grade swap
It is possible to transfer the inclination i. e. of a roof profile from
one side to the other.
7. Inclination Measurement Parallel to Ground
Even if the inclination is unknown, it can simply be adapted to the ground.
9 - 21 10 - 21 8 - 21 11 - 21 12 - 21 7 - 21
Automatik-Kanalbau-Laser
KL-80/-81
= 2.1 ON/OFF Button
The device is switched on by pressing this button. The device and company data
are then shown, followed by the operating display with the last settings without
button lock. The device is then levelled and referenced on the zero point
automatically.After the levelling phase the laser beam and laser beam symbol stop
blinking. If this does not happen, the device must be moved into the levelling range
by tilting it forwards. The display illumination switches off after approx. 30 seconds
automatically. The illumination is switched on again by pressing the ON/OFF
button shortly.
To switch off the device, press the ON/OFF button until “Auf Wiedersehen !”
appears.
= 2.2
When setting-up vertically,the X inclination setting, the y inclination setting and the
rotor setting, when setting-up horizontally the lock symbol and the rotor speed are
selected and released one after the other by pressing the MENU/OK button.
The respectively activated point blinks.
If, after setting the speed, the button is pressed again or a time of about 25
seconds passes, the adjustment guard is reactivated automatically. This means:
the arrow buttons do not work.
Lock-, Rotor Speed- and X Inclination
Setting
or = 2.3
Menu
OK
Arrow Buttons - Release
Select - Set - Confirm
Date 12/2015 Subjct to change
4 - 21 5 - 21 6 - 21
1.8 Bubble Tube (Set-up help).
Universal-Laser UL-89L
FE 53
-
FB-10
L -72E
one for all . .
.
FE-61
= 2.5
Check or Change Device Settings
or automatically after 25 seconds.
6
laser beam
FE-53
Y axis
Horizontal- Set-Up
=
=
=
+
+
+
2. Buttons
1.15 Antenna Remote Control (see 21.)
1. Description
1.1 Function
The automatic universal laser UL-89L is a multifunction laser with
inclination setting for horizontal and vertical use capable of
electronic self-levelling over three axes. It emits a laser
beam, which turns into a light plane as it rotates.
Another laser beam is available exactly square to it.
The operation is made at the laser or optionally with the
wireless control FB-10. The rotating laser beam in the Y axis is locked
by the locking receiver FE-53 and the plumb beam in the Y and X axes
by the FE-61.
1.7 Bulging
GroundArea, niro St.
Protects against damages of
coat and guarantees a secure
stand.
Central fastening thread 5/8“. Identification
mPlumb-Bea
Plumb-Up-Beam
1.12 Rotor Head
Rotor speed adjustable from 200 - 1000 rpm.
1.14 Handle
For easy handling, safe transport and simple set-up.
1.2 Inclination Symbol
Enables clear inclination assignment.
The +/- and X/Y symbols indicate the inclination. The + ranges are
light and the - ranges dark.
The symbol also shows the inclination and its change relative to
the centre axis.
1.6 Laser Warning Sign
Laser class 3R, P < 5 mW
1.4 Keyboard
Clear layout. User-friendly, self-explanatory keys.
1.5 Robust Light Metal Housing
Plastic-coated, swept with nitrogen, 100 % watertight.
1.3 Charging Socket
Behind the dust guard cap.
1.10 Optical sight
for quick alignment of the inclination axis.
1.13 Manual Rotor Setting
Pressed in: rotor motor cut out
Extracted: rotor motor cut in again
By turning: setting of the desired position
1.11 Box Level in rotor head for plumb-down function.
Fixing Foot
Sliding
Foot
Horizontal Set-Up
Vertical Set-Up
Operating Instructions
Congratulations on your new GEO laser
This operating instructions contain enclosed in addition to
information on how to use the laser important safety
information.
First read the safety instructions on the
supplement page and then the operating
instructions carefully before using the laser.
Please note:
1 - 3
Uncompromising versatility
+ much more
Two-Axis Inclination Laser
Levelling Laser
Aligning Laser
Plumb Laser
automatically
lock alignment
find alignment
search for alignment
1.9 LCD-Display, Horizontal Set-up (Pipe Laying)
Lock symbol open / closed
Algebraic sign
Inclination value
Percent sign
Status symbols:
Initialising
Inclination adjustment
Inclination adjustment finished,
power saving mode
T = Kick guard active (see 3.3)
T = Blinks after jerky movement,
laser beam off
Power supply indicator
Scan locking automatic
Radio control with FE-53/-61/FB-10:
connected
connected and laser reception
disconnected
Direction limitation
Centring indicator
Direction arrow
Centre indicator
Laser beam symbol
Laser beam and rotor off by remote
control
Rotor speed (8 = 800 rpm)
< 1/4 < 1/2 < 3/4 >3/4
1.16 LCD-Display, Vertical Set-up (Surface Construction)
A=
E=
T=
P=
V= Lock
K=
M=
R=
U=
L=
B=
W=
S=
Automatic cut out
Sensivity
Kick guard
Percent / Per mil
Radio control
Laser beam modulation
Direction automatic
Grade swap
Laser power
Duty type - laser beam
Factory defaults
Service/workshop information
Factory defaults
on/off
Laser blinks when levelling
Laser off when levelling
off/on
off/on monitored
S= standard for FE-61
P=db
-=off
F= Flicker for LE-7x standing
on/off laser beam
off/on
on/off
=
=
1 - 5 :
,
I= X axis
+= X axis + Y axis
%or ‰
1 - 3 = approx. 5 - 15 mm/100m
1 - 2 = 2
3 - 5 = 3R
Laser class
Laser class
Display Device Settings
1 2 3
4 56 78 910 11 12 13
Although the laser is adjusted precisely by the manufacturer, jolts and strong
vibrations can lead to maladjustment. The laser should therefore be checked
before use:
1. Select a measuring area of approx. 40 m that is as horizontal as possible and
set up the laser with the counter at 0.000%.
2. Set up two control points, one directly in front of the laser and the other in a
distance of approx. 40 m, and measure the distanceto the centre of the laser
beam "a" and "b".
3. Set up the laser behind the second measuring point and repeat the measuring
process in reverse direction, this means measure "A" and "B".
4. If the adjustment is correct, A - a = B - b. This means, the laser beam of the first
installation is parallelto the second one.
Error-free: A - a = B - b
1st build A
a
Hz
40 m
B
b
2nd build
5.3 Height Transfer
5.2 Axis Transfer by Bearing over the Plumb Line
5.1 Axis Transfer with the Alignment Line
5. Transfer Possibilities
Alignment line
2nd plumb
Aim point
Datum
1st plumb
Aim point
plumb line
2.
3.
1. Set up laser over the axis.
2. Look over the plumb line and align it to the alignment rod.
3. Look over the plumb line to the laser beam and align the laser in the
direction.
Measuring rod
Height point
Level device
65 A
B
Rod reading A
- Rod reading B
+ 65 mm
+ 1/2
-----------------------
= Pipe invert
Ø
4. Pipe Laying Made Easy
Mount device over the point of reference in such a way that the bubble tube is
levelled in. Adjust the inclination and align the laser beam to the point of aim.After
that join pipe after pipe and align each end to the target.
4.1. Set-up
The laser can be set up centrically or at a constant distance above the pipe
invert. Suitable legs, tripods and fastening systems are available for this.
Note: If the diameter indicated on the legs does not correspond with the pipe
diameter, the target has to be set up directly in front of the laser and must
be adjusted to the correct height ignoring the diameter marking.
Laser
Construction
Height
Reference
Point
Xnln in
x
Icia
t
o Ais
Aiming Point
Laser
Construction
Height
Scanning locking receiver
Direction arrow
alternately OFF resp.
inclination value
Radio control:
connected
connected and laser reception
disconnected
7.1. Operating Instructions
Mount laser above the reference point and align the Y inclination axis to the
aiming point. Adjust banking in the X axis.
Measure laser construction height with the locking receiver FE-53 and a
levelling rod. Transfer this height to the aiming point.
Release the automatic scan with the A button of the receiver.
The light plane is now automatically directed within typically 2 min./max. 5 min.
to the centre of the receiver and locked there.
The LEDs at the FE-53 are blinking alternately. On the display OFF and the
approx. inclination value are shown alternately.
Now the FE-53 can be removed abruptly off the laser light plane and switched
off. After approx. 30 seconds the exact inclination value is shown on the
display and automatically locked. The % symbol is blinking.
Alternatively the FE-53 can be mounted permanently to realize a long-term
fixing of the laser light plane.
Please note: Never operate the remote control or inclination setting at the
laser in this mode because by this the laser light plane is moved.
Precondition is an established radio link to the FE-53, indicated
by the symbol on the LCD display.
7.2 Display Inclination Measurement (Vertical Laser Set-up)

14 - 21 15 - 21 16 - 21 17 - 21 1 8 - 21 19 - 2 1 21 - 21
Target from DN 500, suitable on and in
the pipe, upright and suspended
09 0017.04.1 KL-05
9
20 - 21
Table of Contents Page
Safety Information. . . . . 1 - 2
Laser Safety . . . . . . . . 2 - 3
Repair.............3
EMC.............3
Guarantee ..........3
Disposal............3
1. Description . . . . . . . . 5 - 6
2. Buttons 6 - 7
3. Device Settings . . . . . 7 - 9
4. ... 10
5. ....10
6. Locking . . . . . . 11
7. Inclination Measurement 11 - 12
12
S1
S2
S3
S4
S4
S5
..........
Pipe Laying Made Easy
Transfer Possibilities
Automatic
8. Adjustment Checking . . . .
Page
Power Supply 13
Battery Charging
Maintenance
14. .....14
15. . . 14
16. . 15
17. . 15
18. 15
19. . . . . 16 - 17
20. . . . . . 18 - 19
21. FB-10 Wireless Control . . . 20
22. ......21
9. ........
10. ......13
11. Radio Control . . . . . . . . 13
12. Troubleshooting . . . . . . . 13
13. .........14
Dimensional Sketch
Technical Specifications
Receiver FE-53
Receiver FE-61
Standard Delivery Package
PipeLaser, Optional Acces.
Rotary laser, Optional Acces.
Refraction Effects
11.Radio Control
1. The serial numbers of the laser, FE-53/-61 and FB-10 must correspond with
each other.
2. Simultaneous operation of FE-53/-61 and FB-10 is not possible.
13 - 21
No. Order No. Type Description
01 0001.295 UL-89L Universal laser
02 0037.18 NE-80 Power supply/Battery charger
03 0019.07 Leg set DN 200 (2 x sliding leg/ 2 x fixing leg)
04 0077.36.002 Double headed wrench 10+13
05 0077.36.003 Hexagon key SW 4
06 0077.36 Transport case
1- 6 0001.295.1 UL-89L with standard delivery package
17. Optional Accessories for Pipe Laser
No. Order No. Type Description
01 0016.07 KL-04 Target frame
02 0016.07.002 Plexi target DN 150 - 300
03 0016.07.003 Plexi target DN 400 - 500
04 0019.08 Leg set DN 250 (2 x sliding leg/ 2 x fixing leg)
05 0019.09 Leg set DN 300 (2 x sliding leg/ 2 x fixing leg)
06 0019.10 Leg set DN 400 (2 x sliding leg/ 2 x fixing leg)
07 0019.11 Leg set DN 500 (2 x sliding leg/ 2 x fixing leg)
08 0019.90 Leg adapter for mounting with 3 legs
1- 8 0127.01.1 KL-AU Pipe laying equipment for UL-89L
2
3
6
2345678
1
09 1035.29 Lightning 2 l
10 1035.27 Storm with digital data display
11 0009.39.1 LE-72 with digital data display
0009.70.1 FE-61
aser receiver
Laser receiver
Laser receiver
12 0009.36.1 FE-53 Locking receiver for laser light plane
13 Locking receiver for plumb beam
14 0026.07 FB-10 Two-way radio control
15 0045.04 DS-80 Rotation axis
18. Optional Accessories for Rotary Laser
910 11 14 15
12 13
4
5
16. Standard Delivery Package
1cold
warmth
22. Refraction Effects: Example Pipe Laying
The laser beam is deflected to cold air.
It is deformed and moved by atmospheric turbulences.
laser beam
laser beam after temperature influence
laser beam
laser beam after temperature influence
cold warmth
warmthcold
Countermeasures:
Do not keep tubes in direct insolation. Store tubes in the shadow or cover them
with a canvas.
Align the pipe in the ditch immediately. If the laser beam is deformed by
temperature influences and/or in movement, define the centre by averaging.
level tube
in the pipe on the pipe
clamping srews for
vertical adjustment
of target
Functions
20.1 Measuring Receiver
The laser receiver FE-61 receives a stationary or rotating plumb laser beam
and indicates its position to the light plane by way of 2 LEDs.
20.2 Locking Receiver for the Plumb-Axis
It automatically directs the stationary or rotating plumb laser beam to the centre
position of the lasers and locks it there. Accuracy to ± 1mm/100 m.
20.3 Receiver Description
X1
X3
Y4
Y2
1X
X3
Y2
Y4
20.6 Outstanding technical specifications:
Accuracy measuring receiver: . . . . . . . . . . . . . . . . . . . to ± 0.1 mm
Accuracy locking automatic: . . . . . . . . . . . . . . . . . . to± 1mm/100 m
Signaltone:............................loud,quietoroff
Power supply: . . . . . . . . . . . . . . 2 x round cell/AA (battery or rech. battery)
Current consumption: . . . . . . . . approx. 100 mA (operating time to 20 hours)
Housing:. . . . . . . . . . . . . . . . . . . . . . watertight, except battery cover
Dimensions / weight: . . . . . . . . . . . . . . . . . 140 x 100 x 32 mm / 0.52 kg
Frequencyrange: .......................2.4GhzISMBand
Transmission power : . . . . . . . . . . . . . . . . . . . . . < 100 mW (EIRP)
Reception: . . . . . . . . . . laser (633 - 815 nm homogeneous beam profile)
..........................Øvon5-20mm,0.8-2mW
Range ...............2to100mdepending on ambient conditions
Distance to illuminants and high-voltage power lines: . . . . . . . . . . > 1.5 m
Conformity with national regulations:
GEO-Feinmechanik GmbH herewith declares that the FE-61 conforms to the
fundamental requirementsand other relevant regulations of directive 1999/5/EG.
= lock automatically
A
1. x briefly = The radio link with the laser is set up
Once the rotating plumb beam hits the measuring quadrant of the receiver it is
automatically directed to the center and fixed there. By slowly moving the laser
receiver, the position of the light surface is changed. The reception is indicated
by symbols on laser and LEDs on receiver.
LEDs blink alternately right and left: the setting phase is completed.
Switch off receiver to switch off the locking function.
= tone loud, quiet or off
1. x briefly = switch on: The FE-61 works as measuring receiver.
1. x long = switch off
Keep the button pressed until the LED of the operating mode display lights
accompanied by a tone sequence or automatically after 15 min. without receipt.
Switch on the FE-61 and move it to the laser light plane until the reception of
the light plane is indicated by LEDs and signal tones.
To receive the required accuracy, move the FE-61 in arrow direction.
= switch on
20.5 Operation
Remote Control
It is possible to adjust manually the direction and height of the laser with the
FE-61 .
To activate the remote control when turning on the receiver press the power
button until the remote LED flashes.
The side (Y axis) can be adjusted with the keys next to the LED.
Switch to the height (X axis) by briefly pressing the power button.
The remote control LED blinks faster.
Now the height can be adjusted using the buttons next to the LED.
Press briefly to return to the measuring receiver function.
20.4 Control Principle
20. Locking and Receiver FE-61Measuring
Robust Metal Housing
Plastic-coated, watertight.
M5 mounting thread at the back of
the housing.
Power Indicator:
LED blinks slowly = device switched on
LED blinks quickly = battery almost
empty
LED off = device switched off
Battery
Compartment Lid
To open in direction of arrow.
Make sure the polarity is correct
when installing the new battery.
Locking Receiver:
Measuring Receiver:
LED blinks = device switched on
LED off = device switched off
Operating Mode Display
LED blinks = Radio control dial-up
LED off = Radio control connected
LED on = Radio control failure
Remote Control Display
Y-axis: LED blinks slowly
X-axis: LED blinks quickly
Orientation Notches
Measuring Quadrant
with solar cells sensor and
LED display
Apart from the ON button, the functions correspond to those of the keyboard
and display of the laser.
Note: It is not possible to switch on the laser and the radio transmission and
to switch off the laser by the FB-10.
21. Wireless Control FB-10
21.1 Functional Description
The remote control FB-10 allows a wireless operation of GEO lasers with radio
module. Laser and receiver have the same keyboards, operating mode
displays, radio transmitters and receivers.
Range while visual contact up to 350 m.
21.2 Device Description
21.3 Button Description (see 2.)
= ON only FB-10
1 x short =ON: The message "Try to connect .. Please wait .." appears
and the remote control connects to the GEO laser within
approx. 20 seconds.
1. x long = laser beam + rotor switched off (stand-by mode)
2. x long = laser beam + rotor switched on again
Note: Press the button until the desired symbol
or appears.
OFF = Auto off after approx. two minutes if no button pressed.
Robust Metal Housing: plastic-coated, 100 % watertight.
15.4 Error Messages:
"Connection Lost!": Communication between laser and remote control
interrupted - establish visual contact with the laser or
reduce the distance to the laser.
Activate wireless remote control in the menu of the
GEO laser (see instructions for use of laser).
"BATTERYLOW": Replace batteries soon.
The LCD light stays off to save power.
"BATTERYEMPTY!": The batteries must be replaced immediately.
Note: The radio transmission can be switched off either in the second
menu level of the laser or of the remote control. A renewed
switch-on of the radio transmission is possible only at the laser.
LCD-Display
Clearly legible,
illuminated display
Battery Compartment
Cover
To open in direction of arrow.
When inserting the battery
observe the correct polarity.
Antenna
Antenna Lock
Keyboard
Easy to handle, clear
layout, user-friendly.
12.Troubleshooting
1. No laser beam - check battery charge.
2. Low range - clean laser beam exit window.
3. Laser beam blinks slowly - move device into the levelling range by tilting
forwards.
4. Laser beam and banking arrows blink slowly - reset laser from the limitation.
If the errors of points 3 and 4 are not corrected within 2.5 minutes, the device
is switched off automatically.
5. Laser switched off automatically (kick guard or direction automatic
monitoring) - Switch on laser beam by pressing the ON button shortly.
9. Power Supply
7.4 V DC internal lithium ion rechargeable battery or 12 V DC external
rechargeable battery via connection cable 0117.02.
10. Battery Charging
• Carry out charging only with the power and charging unit, type NE-80 or
a 12 V DC external rechargeable battery via connection cable 0117.02.
• Keep charger dry and only use in rooms.
• For charging take the laser out of the transport case.
• Permissible charging temperature 0°C to + 40°C, as best + 10°C to + 25°C.
• After approx. 5 hours the charging time is finished. The display dies down or
the battery symbol shows a full battery.
• Low ambient temperatures reduce the running time, high temperatures
reduce the battery life.
• Damaged batteries must be disposed. Robust Metal Housing
Plastic-coated, watertight.
M5 mounting thread at the back of
the housing.
19. Locking and Measuring Receiver FE-53
Functions
19.1 Measuring Receiver
.
19.2 Locking Receiver for the X Inclinatin Axis
It directs the rotating laser beam over the whole inclination range automatically
to the centre position of the receiver and locks it there.
The laser receiver type FE-53 receives the rotating laser beam and indicates
its position to the light plane by way of three LEDs and various signal tones
Accuracy to ± 1mm/100 m.
19.3 Receiver Description
Power Indicator:
LED blinks slowly = device switched on
LED blinks quickly = battery almost empty
LED off = device switched off
Battery
Compartment Lid
To open in direction of
arrow. Make sure the
polarity is correct when
installing the new battery.
Locking Receiver
Meas. Receiver ± 0.1 mm
Meas. Receiver ± 1 mm
LED + slow tone sequence
LED + quick tone sequence
LED + steady tone = middle
LED + Tone alternating = middle
Locking Receiver:
Meas. Receiver:
LED blinks = device switched on
LED off = device switched off
Operating Mode Display
LED blinks = Radio control dial-up
LED off = Radio control connected
LED on = Radio control failure
switch over from measuring to locking receiver:
search, find and lock automatically
19.5 Operation
A
1. x briefly = The radio link with the laser is set-up and the laser light plane is
directed to the centre of the receiver and locked there
automatically.
As soon as the rotating laser beam hits the arrow range of the
receiver, it is automatically directed to the middle and locked
there.
The direction of the laser light plane can be changed by slowly
moving the laser receiver.The reception is indicated by a symbol at
the laser and LEDs at the receiver:
- LEDs blink simultaneously right and left >laser searches for receiver
- LED blinks right or left >receiver found
- LEDs blink alternately right and left >setting finished:
centre found and locked
2. x briefly = laser searches for the receiver again.
Switch off receiver to switch off the locking function.
1. x briefly = Measuring receiver with an accuracy of +/- 1 mm.
Move FE-53 towards the light plane until the reception of the light
plane is indicated by LED and signal tone.
To reach the desired accuracy move the FE-53 in arrow direction:
Accuracy: One LED blinks in the middle = +/- 1 mm
2. x briefly = Measuring receiver with an accuracy of +/- 0.1 mm
Accuracy: Two LED's blink alternately = +/- 0.1 mm
3. x briefly = Back to measuring receiver with an accuracy of +/- 1 mm.
1 x long = Switch off
Press button until the LED of the operating mode display flashes
accompanied by a tone sequence or automatically after 15 min.
without reception.
=
= tone loud, quiet or off
= switch on/off
19.8 Outstanding Technical Specifications:
Accuracy direction automatic: . . . . . . . . . . . . . . . . . to ± 1 mm/100 m
Accuracy laser receiver: . . . . . . . . . . . . . . . . . . ± 1mm or± 0.1mm
Reception range/-angle: . . . . . . . . . . . . . . . . . . . . . 85mm /> 100°
Rotorspeed:...........................600-1000rpm
Signaltone:............................loud,quietoroff
Power supply: . . . . . . . . . . . . . . 2 x round cell/AA (battery or rech. battery)
Current consumption: . . . . . . . . approx. 100 mA (operating time to 25 hours)
Housing:. . . . . . . . . . . . . . . . . . . . . . watertight, except battery cover
Dimensions / weight: . . . . . . . . . . . . . . . . . 140 x 100 x 32 mm / 0.52 kg
Frequencyrange:........................2.4GhzISMBand
Transmission power : . . . . . . . . . . . . . . . . . . . . . < 100 mW (EIRP)
Guarantee:..............................24months
CE:....................................certified
Range depending on ambient conditions : . . . . . . . . . . . . . 2 to 250 m
Distance to illuminants and high-voltage power lines: . . . . . . . . . . > 1.5 m
Conformity with national regulations:
GEO-Feinmechanik GmbH herewith declares that the FE-53 conform to the
fundamental requirementsand other relevant regulations of Directive 1999/5/EG.
The declaration of conformity can be found at the following address:
http://www.geo-laser.de.In countries with national regulations that are not covered
by European directives the operator must himself check the provisions and
permits for use.
The permit for use is only valid for use with antenna of up to 3 dBi.
6
laser beam
19.4 Control Principle
The FE-53 can be mounted either on the left or on the right side of the laser.
Because of reasons of functionality, the keyboards of both devices must be
on the same side.
Y
Y
The declaration of conformity can be found at the following address:
http://www.geo-laser.de.In countries with national regulations that are not covered
by European directives the operator must himself check the provisions and permits
for use.
The permit for use is only valid for use with antenna of up to 3 dBi.
Guarantee:..............................................24months
CE: ......................................................certified
Horizontal Set-up
Only control of the Y axis or - after switch-off of the automatic
levelling (see 3.1) - of the Y and X axes.
Vertical Set-Up
Control of the Y and X axes after switch-off of automatic levelling
(see 3.1).
14. Dimensional Sketch
15. Technical Specifications
Laser class Laser type
Range depending on circumstances and receiver
Inclination range
Self-levelling range over the complete inclination range
Speed adjustment
Locking automatic laser light plane: . . . . . up to 250 m with receiver FE-53
Locking automatic plumb beam: . . . . . . . up to 100 m with receiver FE-61
External power supply:. . . . . . . . . . . . 11 to 14 V DC with cable 0117.02
Low battery cut-out
Watertight
Temperature range
eight
Frequency range: . . . . . . . . . . . . . . . . . . . . . . 2.4 Ghz ISM Band
Transmission power :. . . . . . . . . . . . . . . . . . . . . < 100 mW (EIRP)
Guarantee: .............................24months
CE:...................................certified
/ : . . . . . . . . . 3R, < 5 mW/diode, visible red, 635 nm
: . . . . . to 250 m, Ø 500 m
:....................Xaxis -5%to+20%
Inclination range: . . . hz. mounting by tilting forward, X axis - 10 % to + 20 %
Inclination range/direction setting range:. . . . . . . . Y axis - 5 % to + 5 %
Inclination range with rotation of device: . . . . . X axis ± 20 % / Y axis ± 5 %
:............
Readingprecision:........................... 0.001%
Permissible deviation: . . . . . . . . . . . . . . . . . . . . . . ± 5 mm/100 m
:.....................from200-1000rpm
:.............................yes
: ..............................to0.35m
: .....................-10°Cto+50°C
Dimensions/w : . . . . . . . . . . . . . Ø 130 mm,length 295mm/3.6 kg
Operating time with 7.4 V DC Li Ion recharg. battery: . . . . . . to 27 hours
Working distance radio control:. . . . . . . . . . . . . . . . . . . up to 350 m
The range is reduced by obstacles in the way of the radio signal.
Conformity with national regulations:
GEO-Feinmechanik GmbH herewith declares that the devices UL-89L, FB-10,
FE-53 and FE-61 conform to the fundamental requirements and other relevant
regulations of directive 1999/5/EG.
The declaration of conformity can be found at the following address:
http://www.geo-laser.de. In countries with national regulations that are not
covered by European directives the operator must himself check the provisions
and permits for use.
The permit for use is only valid for use with antenna of up to 3 dBi.
13. Maintenance
The laser requires no special maintenance. Keep the electrical connections
clean. Do not clean with water spray. Clean glass parts with a soft, clean cloth.
Store dry.Always transport the laser in its original case.
20
64Ø
5/8"
152
73,5 20
180Ø
DN
150
200
250
300
400
500
----
83
103
123
163
204
208
227
240
253
280
307
BC
GEO-Laser GmbH
Solinger Str.8
45481 Muelheim an der Ruhr
Germany
Phone [phone]
Fax [phone]
[e-mail]
www.geo-laser.de
GEO - partner of the construction industry for 50 years
German Quality Product
CE
Certified