Digi-Pas DWL-130 User manual

Product of Singapore
Clip-On (Module)
DIGITAL LEVEL
USER MANUAL
Digi-Pas®
DWL-130 (0.05° Resolution)

Buzzer sound
Device Overview :
Adjustable Clip
Locking Flip
LCD Display
MODE SELECT :
- Press to change display unit
: °(Degree), %slope, mm/M, In/Ft
- Press & Hold to freeze Display value CAL: Activate Calibration Mode
ON/OFF : Power on/o
device
Alt.Zero :
- Set any angle to 0° as reference
- Press & Hold to turn on/o buzzer sound
Cleaning
• Keep the level dry and clean. Remove
any moisture or dirt with a soft, dry cloth.
• Do not use harsh chemicals, strong
detergents or cleaning solvents to clean
the level.
• Do not submerge device in water while
cleaning .Wiping or cleaning on device
surface is sufficient

Dimension : 95 x 48 x 22mm
Weight : 110 Grams
Operating Temp : 0° ~ +50°(Celcius)
Storage Temp : -10° ~ +60°(Celcius)
Battery : 2 x CR2032 (3V)
Technical Specification
Cleaning
• Keep the level dry and clean. Remove
any moisture or dirt with a soft, dry cloth.
• Do not use harsh chemicals, strong
detergents or cleaning solvents to clean
the level.
• Do not submerge device in water while
cleaning .Wiping or cleaning on device
surface is sufficient

Battery Compartment
Push down the battery cover to slide open.
For the rst time usage, remove the plastic strip to
connect the battery

Caution
Digi-Pas device is calibrated in the factory for maximum
accuracy. User can re-calibrate when necessary.
Please refer to www.digipas.com for video demonstration
on how to calibrate the device.
®
Clip the device to a spirit level, make sure the device is
securely cliped on the level, turn on the device then press
‘CAL’ button once the screen will display flashing “CAL1”.
Place the device on a flat and clean surface, press
“MODE” button once, the screen will display countdown,
wait until screen countdown reach “0” and show “CAL2”.
Rotate the device (180°) parallel to the surface then press
“MODE” button again, the screen will display countdown,
wait until screen countdown reach “0” and show “CAL3”.
Position the device vertically (-90°) on a level surface,
press “MODE” button again, the screen will display
countdown, wait until screen countdown reach “0” and
show “CAL4”.
Rotate the device 180° parallel vertically to the surface
(+90°) then press “MODE” button again, the screen will
display countdown, wait until screen countdown reach “0”.
Calibration Done.
1.
2. a
b
c
d
3.
Calibration Instruction
Note: Ensure the device is kept still during calibration

Calibration Illustration

Warranty
Digi-Pas® Digital level is warranted to the original purchaser to be free
from defects in workmanship and material. JSB Tech will, at its option,
repair or replace any detective part which may malfunction under
normal and proper use within a warranty period of 1 (one) year from
the date of shipment. This one year warranty clause is NOT applicable
to European Union (EU) member states. Purchases made in EU
member states will be covered by the existing consumer laws across
the European Union, which provide statutory warranty rights in
addition to the coverage of one year warranty period. The foregoing
warranty shall not apply to defects resulting from misuse, abuse or
transfer by the Buyer, Buyer-supplied software or interfacing,
unauthorized modification or operation outside of environmental
specifications for the product. JSB Tech does not warrant that the
operation of the instrument software, or firmware, will be uninterrupted
or error free.
The exclusive remedy under any and all warrants and guarantees,
expressed herein, and we shall not be liable for damages from loss or
delay of equipments uses, consequential, or incidental damage. No
other warranty is expressed or implied. JSB Tech specifically disclaims
the implied warranties of merchantability and fitness for a particular
purpose.
In no event shall DIGIPAS USA, LLC., (hereinafter, “the Company”) be
liable to you or any third party for any indirect, special, incidental,
exemplary or consequential damages of any kind resulting from any
breach of warranty or from the performance or use of the product. This
includes without limitation: property damage, loss of value of the
product or any third party products that are used with the product, or
loss of use of the product or any third party products that are used with
the product, even if the Company has been advised of the possibility
of such loss or damages. The Company’s total cumulative liability
arising from or related to the product, whether in contract, tort
(including negligence) or otherwise, shall not exceed the amount
actually paid by you for the product. Some states and/or jurisdictions
do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.
If any limitation of liability shall be deemed invalid by any applicable
law, then the limitations of liability set forth above shall apply to the
maximum extent permitted under applicable law.
Limitation of Liability

Manufactured by
JSB TECH Pte Ltd
Email: [email protected]
www.digipas.com
Distributed by :