George Home Wooden 2 in 1 shop & café User manual

OR
Cross head / Philips
screwdrivers suitable
for use with the
screws and small
bolts and a pair of
pliers or a spanner
for the nuts.
You will need...
1.Unpack the
components
and check
against the list
below.
2.Place the
components on
a clean surface
to prevent them
from being
damaged.
3.After you have
assembled your
toy, dispose of
all packaging.
Getting started...
A x1 D x2
B x1 E x2
C x2 F x2
G x1 O x1
H x1 P x4
I x1 Q x16
J x1 R x16
K x1 S x28
L x1 T x1
M x1 U x6
N x1 V x1
You will have...
Wooden 2 in 1 shop & café
Assembly Guide
IMPORTANT: RETAIN FOR FUTURE REFERENCE
WARNINGS:
• IMPORTANT SAFETY INSTRUCTIONS
• PLEASE READ ALL INSTRUCTIONS CAREFULLY
BEFORE USE AND RETAIN FOR FUTURE
REFERENCE.
• Adult assembly required.
• The hardware contains small screws with sharp points.
Keep unassembled parts out of the reach of small
children.
• WARNING! Not suitable for children under the age of 36
months. Components of this product may break off into
small parts presenting a choking hazard.
• Choking hazard: Unassembled parts may be a choking
hazard to children 3 years and younger.
• To avoid the danger of suffocation, keep any bags
or packaging away from babies and children. Any
packaging or bags are not part of the toy and must be
disposed of immediately before assembling the toy.

Step 1
Attach the castors (P)
to the base (A) using
the sixteen short bolts
(Q) and nuts (R).
Step 2
Attach the left
side (B) to the
base using
two long
screws (S).
Step 3
Attach the two
front rails (C) to
the side panel
using two long
screws (S).
Step 6
Attach the
right side
panel (F) to
the assembled
sections using
eight long
screws (S)
Step 9
Fasten the
wooden stud
(H) to the left
side panel
using the
small screw
(T).
Step 4
Attach the two
dividers (D) to the
two shelves (E)
using two long
screws (S).
Step 7
Slide the back
panel (G)
(with the black
face facing
upwards) into
the slots in the
side panels.
Push the back
panel into
the slot in the
base.
Step 5
Attach the shelves
to the side panel
using four long
screws (S).
Step 8
Stand the
assembled
sections upright
and fasten the
front rails to the
divider using two
long screws (S).
P
Q
R
A
B
S
C
S
S
D
E
D
E
S
S
H
T
S
G

How to...
...care for and maintain your shop & café
• Your toy is only meant to be assembled once.
• After you have assembled your toy do not dismantle it
again as this may weaken the joints and screws leaving
the toy unsafe for use.
• Regularly check that all of the screws are fully tightened
(but do not over-tighten).
• Use the toy on a flat level surface only.
• Please check the assembly of the toy regularly and
frequently tighten any screws or bolts. If regular
maintenance is not carried out the product may cease to
function properly.
Step 10
Place the top panel (I) on
the assembled section
and fasten in place using
four long screws (S).
Step 11
Slot the left (J) & right (K) uprights
into the slots in the top panel. From
the inside of the assembled sections,
fasten the uprights to the side panels
using the six long bolts (U) and the
allen key (V).
Step 12
Slot the long (L) and short (M)
poles into the sleeves in the
fabric canopy (N).
Step 15
Now you have completed
the assembly of the
wooden 2 in 1 shop &
café, check all of the
screws and bolts are fully
tightened.
Step 13
Fasten the
short pole (M)
to the uprights
using two long
screws (S).
Fasten the long
pole (L) to the
canopy arms
using two long
screws (S).
Step 14
Slot the top board
(O) into the slots
in the tops of the
uprights.
Customer services
information
If you require further information,
spare parts or advice regarding
your product, or if you are
experiencing any problems, please
contact customer services at the
telephone number or address
shown opposite. N.B. When calling
or writing please quote the product
name.
Call
0800 952 0101
Write
Asda Stores Ltd.
Asda House, Southbank, Great Wilson
Street,
Leeds, LS11 5AD
Product name:
Wooden 2 in1 Shop & Café
S
I
K
J
U
V
M
L
N
O
S
SM
L
There are many more wooden role-
play toys to purchase and enjoy