geos SD582BT Specification sheet

User Quick Setup Manual
1. Open the package and check the appearance
and accessories
2. Please press the button to turn the scanner on
3. Connecting and transmitting schemes
Attention please: The default connection mode of the scanner
is 2.4G, which can be configured into Bluetooth mode as needed.
After booting, it will try to connect according to the connection
method before shut down. For example, before the scanner turns off,
the scanner and the mobile phone Bluetooth pair successfully. After
rebooting, the scanner will automatically connect to the mobile
phone while the mobile phone has not ignored the scanner and its
Bluetooth on.
Scanner function setting step:
3.1 Bluetooth mode
Turn on the Bluetooth of terminal devices and use the scanner
scans“EnterSettings”-“BluetoothHID Mode”-“Searching”-“Exit
Settings” in sequence. Find and choose the “Barcode Scanner HID”
on the terminal device to connect. If successfully, the blue colored
indicator will be on. (Note: For the meaning of indicator refer to part
7).
①Enter Settings
②Bluetooth HID Mode
③Searching
④Exit Settings
3.2 2.4G mode
After plugging Dongle into the computer and the computer
identifying Dongle successfully, pls. scan “Enter Settings”-“2.4G
Mode”-“Connect Dongle”-“Exit Settings” in sequence to pair.
After connect successfully, the blue colored lights will be on. (Note:
For the meaning of indicator refer to part 7).
①Enter settings
②2.4G Mode
③Connect Dongle
④Exit Settings
4. Active Factory Defaults
Scanning the “Active Factory Defaults” barcode below will
return the scanner to its factory configuration. This barcode does not
change the connection and transmission method.
Active Factory Defaults
5. Function configuration
5.1 Configure carriage return (CR), line feed (LF)
Add CR
Add LF
Add CR/LF
Clear CR/LF
6. Power down method
The scanner will automatically shut down after it connects
successfully but not in use longer than 10 minutes. When you do not
use the scanner device, you can scan the following barcodes in
sequence to shut down the scanning device directly.
①Enter Settings
②Power Down
7、Country languages
Enter Settings
Reading function barcode
Exit Settings

English
Spanish
Italian
French
German
Finland
Sweden
8. Meaning of indicator status &beeper tone
The blue colored light and the green colored light flash
alternately: The scanner under Bluetooth searching.
The green colored light single flashes: The scanners try to pair
with the Dongle through 2.4G mode.
The blue colored light always on: The scanner under
connection. The light will turn off after disconnect.
The two green colored lights flash one after one: The scanner
under connection. Decoding and transmitting are successful.
One green light colored flashes while the other one flashes two
times: The scanner disconnected, the decoding is successful but
transmitting fails.
Beep three times: The device receives message abnormally
from Scanner.
Beep twice: Disconnected.
Beep once: Good connection. Scanner power on. Good
transmission.
Beep always: Low battery Alert. Shut down and charge ASAP.
The red colored light always on: The scanner is charging, and
light will off after charging completion.
9. Common Questions
9.1 What to do if can not connect to Bluetooth?
Make sure the phone is android 3.0 or above, go to 3.1
Bluetooth Mode setting and scan functional barcodes in sequence,
open the mobile phone Bluetooth, search for a new device, and click
“Barcode Scanner HID” to connect.
9.2 Why part of the barcodes can not scan?
Because some uncommon barcode types are turned off by
default, you can scan functional barcode to open the dedicate
barcode types. If you do not know the functional barcode, please
contact your supplier.
9.3 Why barcodes can not be uploaded to a computer
or phone?
S1 Make sure the scanner turns on and works normally.
S2 Determine whether the scanner and the terminal device are
under good connection. The blue colored light on scanner is off pls.
go to S3. It is on pls. go to S4.
S3 The scanner and the terminal device do not connect
successfully, please go to 3.1 Bluetooth Mode setting or 3.2 2.4G
Mode setting. Confirm good connection and then scan the barcode
to transmit.
S4 Please check if there is other terminal device in the
communication range. If the scanner connects to other terminal
device, please disconnect and go to 3.1 or 3.2 to connect with this
terminal device.
9.4 How to do if computer or mobile phone cannot find
the Bluetooth scanner?
First pls. check if the Bluetooth of the terminal device works
normally. If yes, pls. go to 3.1 Bluetooth Mode setting.
9.5 Bluetooth scanner has been connected with the
phone or computer through Bluetooth before, how to
pair with the phone or computer again?
If the scanner does not connect with other devices after
disconnecting with this terminal device, the scanner will connect
with the terminal device automatically while both of them turn on.
If the scanner has connected with other devices, or the automatic
connection with this device fails, pls. delete the paired Bluetooth
(“Barcode Scanner HID”) on the terminal device and go to 3.1
Bluetooth Mode setting.
9.6 The Bluetooth of the scanner connects with device-
A first, then connects with device-B, and then
disconnects with device-B, will it connect with device-
A automatically?
It will not connect with device-A automatically. You need
delete the paired Bluetooth (“Barcode Scanner HID”) on the A

device and go to 3.1 Bluetooth Mode setting.
9.7 The scanner connects to the terminal device, how
to connect with another terminal device?
9.8 Will it reconnects automatically after turning it off?
2.4G mode: When Dongle connects to the terminal device and
the scanner has not established a new connection with other terminal
devices, the scanner will connect automatically after re-power on.
Bluetooth mode: The terminal device establishes a connection
through Bluetooth Mode before the scanner turns off. After shutting
down, there is no deletion on the Bluetooth list of the terminal
device, the scanner will connect automatically after re-power on.
If the connection is not successful, go to 3.1 or 3.2.
9.9 Why Red light does not shine when charging?
Please confirm the power supply device turns on, let the
scanner power off and charge again.
10. Technical supporting
If this manual doesn’t solve your problem, please contact your
supplier.
Connect A in 2.4G mode
Pull the dongle out of A
Scan required barcode
Plug dongle into B or
open B’s Bluetooth
connect B
connect A in Bluetooth mode
Close A’s Bluetooth