geratech EGE-UHDAUD-AMP User manual

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
3
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate.
Cypress Technology assumes no responsibility for any infringements of patents or other
rights of third parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies that may be contained
in this document. Cypress also makes no commitment to update or to keep current the
information contained in this document.
Cypress Technology reserves the right to make improvements to this document and/or
product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval
system, or any of its part translated into any language or computer le, in any form or by
any means—electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—
without express written permission and consent from Cypress Technology.
© Copyright 2015 by Cypress Technology.
All Rights Reserved.
Version VR1.0 January 2015
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the
companies with which they are associated.

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment
and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of re, electrical shock and
injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain, moisture or install this
product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots
in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed
upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit
housing that provide ventilation and allow for sufcient space for air to circulate around
the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 23/01/14 Preliminary Release
RDV2 17/04/15 Power Adaptor
RDV3 29/05/15 e-Audio connection

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
5
CONTENTS
1. Introduction.............................................................1
2. Applications ............................................................1
3. Package Contents ..................................................1
4. System Requirements............................................1
5. Features...................................................................2
6. Operation Controls and Functions .......................3
6.1 Front Panel..........................................................3
6.2 Rear Panel...........................................................4
6.3 RS-232 Pin Assignment.......................................5
6.4 IR Cable Pin Assignment.....................................6
6.5. Remote Control ..................................................7
6.6 OLED Menu.........................................................8
6.7 Telnet & RS-232 Command.................................9
6.8 Telnet Control ....................................................11
6.9 WebGUI Control ................................................13
7. Connection Diagram ............................................14
8. Specications .......................................................15

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
1
1. INTRODUCTION
The HDBaseTTM 4K UHD with Digital Presentation Amplier can accept analog and
digital audio from 3.5Ø line in, L/R RCA, HDMI, optical and coaxial inputs and output
synchronously to L/R speaker, HDMI and HDMI over CAT5e/6/7 Receiver. Suitable for
any musical events use, sound addition, sound amplifying and AV extension. With audio
sampling rate supports up to 96kHz and I/O data rate supports up to 24-bit, it provides
a high standard of quality sound presentation and can amplier sound up to -80dB. The
system also support HDBaseTTM features including the transmission/receiving high
denition audio and video, PoC (Power over Cable), RS-232 and Ethernet up to 100
meters. The HDMI input/output resolution supports up to 4Kx2K, 3D, 36-bit Deep color, Hi-
Def. new lossless audio and other features dened by the HDMI specications.
2. APPLICATIONS
• Public Speech
• Show even audio set up
• Home theater/Entertainment
• Educational/Lecture presentation
3. PACKAGE CONTENTS
• 1 x HDBaseT 4K UHD with Digital Presentation Amplier
• 1 x Remote Control CR-141
• 1 x 24V/3.75A DC Power Adaptor
• 1 x Power Cable
• 1 x Rack Ears Set
• Operational Manual
4. SYSTEM REQUIREMENTS
Input audio source equipment such as DVD/Blu-ray players, PC, CD player, MP3, HDMI
over CAT5e/6/7 Transmitter and Receiver and etc…. with output display TV/monitor and
active speakers and connection cables.

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
2
5. FEATURES
• Supports Digital to Analog audio Conversion (DAC) and Analog to
• Digital audio Conversion(ADC)
• Supports input sampling rate up to 96kHz and output at 48kHz
• Speaker each output channel supports 30W/4ohm
• Synchronous output sound on both digital and analog
• Supports HDTV resolutions up to 4Kx2K (3840x2160@24/25/30 & 4096x2160@30Hz)
• Supports distances up to 100 meters through CAT5e/6/7 cables
• HDBaseTTM support PoC (Power over Cable), RS-232 and Ethernet
• Supports RS-232, Telnet, WebGUI, IR and on-panel controls
• Sound supports up to -80dB

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
EXIT POWER
SERVICE MENU
HDBaseT™ 4K UHD with Digital Presentation Amplifier
1 2 3 4 5 6
1Service: Connect with USB ash driver for rmware update only.
2OLED: Display current input source selection and volume setting.
3IR Window: Accept IR signal from the remote control included in the package.
4MENU: This button has two usage, one for volume control and the other for menu
selection. Turn the wheel to adjust the output sound volume before entering into menu
selection or press it to enter into the menu selection then turn the wheel to rotate from
the selection and press it again to enter or to conrm the selection.
5EXIT: Press this button to exit from the menu selection. When outside the menu
selection press this button to mute the output sound, the LED will illuminate. Press it
again to unmute.
6POWER: Press this button to turn on the device and the LED will illuminate in blue,
press it again to switch to standby mode and the LED will turn red.

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
4
6.2 Rear Panel
SPEAKER
RS-232
CAT5e/6/7 OUTCAT5e/6/7 IN
COAX.
LANAUDIO-CAT HDMI OUT HDMI IN OPT.
IN
IN RL
RL
+
-
+
-
DC 24V
1
2
3
4
V+
GND
GND GND
V+
LINE IN IR IN IR OUT
RCA IN
1 3 4 6 8 1511
2 5 7 9 10 1312 14
1LAN: Connect from PC/Laptop with RJ-45 cable for Telnet/WebGUI controls.
2RS-232: Connect from PC/Laptop with D-Sub 9pin cable for RS-232 controls.
3AUDIO-CAT: Connect from audio Transmitter over CAT5e/6/7 extender for audio
receiving up to 300m.
4HDMI OUT: Connect to HD TV/monitor for both audio and video display.
5CAT5e/6/7 OUT: Connect to HDMI over CAT5e/6/7 Receiver for Audio & Video, IR, RS-
232, LAN and PoC signal sending up to 100m.
6HDMI IN: Connect to DVD/Blu-ray player or any HDMI source equipment for input audio
and video signal sending.
7CAT5e/6/7 IN: Connect from HDMI over CAT5e/6/7 Transmitter for receiving Audio &
Video, IR, RS-232 and LAN signal up to 100m away.
8OPT. IN: Connect from source equipment such as Set-top-box or PS3 or any other
source with optical output for audio signal sending.
9COAX. IN: Connect from source equipment such as Set-top-box or PS3 or any other
source with coaxial output for audio signal sending.
10 RCA IN: Connect from audio source equipment with RCA jack for stereo audio input.
11 SPEAKER: Connect from speakers with wired cable for stereo audio output.
12 LINE IN: Connect from audio device with 3.5ø pone jack for stereo audio signal input.
13 IR IN: Connect the IR Extender for IR signal reception. Ensure that remote being used
is within the direct line-of-sight of the equipment to be controlled.
14 IR OUT: Connect to IR Blaster for IR signal transmission. Place the IR Blaster indirect
line-of-sight of the equipment to be controlled.
15 DC 24V: Plug the 24V DC power supply into the unit and connect the adaptor to an AC
outlet.

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
5
6.3 RS-232 Pin Assignment
Remote Control
PIN Assignment PIN Assignment
1 NC 1 NC
2 Tx 2 Rx
3 Rx 3 Tx
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 115200bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
6
6.4 IR Cable Pin Assignment
3
1
2
3
1
2
Power
IR Blaster Signal
NC
IR Signal
Power
Grounding
IR Receiver
IR Blaster

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
7
6.5. Remote Control
1Power: Press this button to turn on the device or to set it to
standby mode.
2Vol +/-: Press these buttons to adjust the volume.
3MENU: Press this button to enter into the menu selection
4EXIT: Press this button to exit the selection.
5MUTE: Press this button to mute the output audio sound.
Press it again to unmute.
6Audio selection: Press one of these hot key to select audio
input source.
7HDMI OUT: Press these hot keys to select HDMI output
source signal.
8HDBaseT OUT: Press these hot keys to select HDBaseT
output source signal.
HDBaseT
HDBaseT
HDBaseT
OUT
HDMI
OUT
VOLɮMENU
EXIT
VOLɯ
eAUDIO
MUTE
HDMI HDBaseT
OPTICAL RCA
COAXIAL LINE IN
HDMI HDMI
CR-141
3
4
6
8
5
2
7
1

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
8
6.6 OLED Menu
Audio In
Display Set
IP Cong
Function Select Reset to Default
EDID Mode
Video Set
Line IN
RCA IN
Optical
Audio Select Coaxial
eAudio
HDMI
HDBaseT
TimeOut 5s
Display Setting TimeOut 10s
TimeOut 15s
IP Cong
IP Conguration SN
GW
Reset to Default OK?
INT
EDID Mode EXT
Setting HDBaseT
HDMI
HDMI HDMI Setting HDMI
Video Select HDBaseT
HDBaseT HDBaseT Setting HDMI
HDBaseT

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
9
6.7 Telnet & RS-232 Command
Command Description Parameter
?
DISPLAY LIST OF
COMMANDS, CODE
ENTRY IS CASE
SENSITIVE
HELP
DISPLAY LIST OF
COMMANDS, CODE
ENTRY IS CASE
SENSITIVE
PWR POWER CONTROL 0:OFF 1:ON
SOURCE AUDIO IN SELECT
S:STATUS 0:LINE IN
1:RCA IN 2:OPT. 3:COAX.
4:eAUDIO 5:HDMI
6:HDBaseT
VOL OUTPUT VOLUME
SETTING
S:SHOWVOL +:+0.5dB
++:+2dB -:-0.5dB --:-2dB or
0~-80dB
MUTE OUTPUT VOLUME MUTE
CONTROL.
S:STATUS 0:UN-MUTE
1:MUTE
HDMI HDMI OUT SOURCE
SELECT
S:STATUS 0:HDMI
1:HDBASET
HDBASET HDBASET OUT SOURCE
SELECT
S:STATUS 0:HDMI
1:HDBASET
EDID EDID MODE SELECT S:STATUS 0:INT 1:EXT
2:HDBaseT 3:HDMI
FADEFAULT FACTORY DEFAULT
SETTING
REBOOT REBOOT THE UNIT
SIPMODE SET THE IP MODE 0:STATIC IP 1:DHCP
IPCONFIG
PRINT THE IP
CONFIGURATION TO THE
SCREEN
SHOWMAC
PRINT THE MAC
ADDRESS TO THE
SCREEN
SHOWTPORT
PRINT THE TELNET
COMMUNICATION PORT
TO THE SCREEN
SHOWHPORT
PRINT THE HTTP
COMMUNICATION PORT
TO THE SCREEN
SIPADD SET THE IP ADDRESS
SNETMASK SET THE NET MASK
ADDRESS

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
10
Command Description Parameter
SGATEWAY SET THE GATEWAY
ADDRES
SHTTPPORT SET THE HTTP
COMMUNICATION PORT [1-65535] [80]
STELNETPORT SET THE TELNET
COMMUNICATION PORT [1-65535] [23]
Note:
1. All the RS-232 command will be not executed unless followed with a carriage return.
All commands are insensitive.

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
11
6.8 Telnet Control
To access the telnet control under MS windows, click ‘Start’ menu and type
“cmd” in the search eld then press enter.
Under Mac OS X, go to Go → Application → Utilities → Terminal
See below for reference.
Once in the command line interface (CLI) type "telnet", then the IP address,
and hit enter.

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
12
Press “Help” or “?” then hit enter to bring up all available commands.
Note: Any commands will not be executed unless followed by a carriage
return. Commands are case-insensitive. If the IP is changed then the IP
Address required for Telnet access will also change accordingly.

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
13
6.9 WebGUI Control
On a PC/Laptop that is connected to an active network system, open a web
browser and type device’s IP address (available from LCM monitor) on the
web address entry bar. The browser will display the device’s control page.

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
14
7. CONNECTION DIAGRAM
SPEAKER
RS-232
CAT5e/6/7 OUTCAT5e/6/7 IN
COAX.
LANAUDIO-CATHDMI OUT HDMI IN OPT.
IN
IN RL
RL
+
-
+
-
DC 24V
1
2
3
4
V+
GND
GND GND
V+
LINE IN IR IN IR OUT
RCA IN
7m
3m 3m
60°
m
1.5m
60°
7m
3m 3m
60°
m
1.5m
60°
7m
3m 3m
60°
m
1.5m
60°
OPTICAL
IN
OPTICAL
OUT
RS-232
AUDIO - CAT DC 12V
POWER
Power
Link
CAT 5e/6 Out
DC 5V
IR2 Extender
RS232 In IR1 Blaster
HDMI In
Power
Link
CAT 5e/6 In
DC 5V
IR1 Extender
RS232 Out IR2 Blaster
HDMI Out
RS-232 Equipped
Device
RS-232 Equipped
PC or Notebook
Single CAT5e/6 Cable
Active Speakers
IR
Extender IR
Blaster
DVD or Blu-ray Player
DVD or Blu-ray
Player
DVD or Blu-ray
Player
PC/NB
PC/NB
HD
TV
RS-232
Adaptor
Display

EGE-UHDAUD-AMP
Integrated Zone Amplifier with HDBaseT Capability
15
8. SPECIFICATIONS
Video Bandwidth 300MHz/9Gbps
Ethernet Speed 100Mbps
Input ports 1x HDMI, 1xCAT5e/6/7, 1 x Optical, 1 x
Coaxial, 1 x 3.5Ø Line in, 1 x R/L RCA, 1 x
D-Sub 9pin (RS-232), 1 x RJ-45 (LAN), 1 x
Keypad, 1 x IR, 1 x AUDIO-CAT
Output ports 1 x HDMI, 1 x CAT5e/6/7, 1 x R/L, 1 x IR, 1
x AUDIO-CAT(same as input port)
Digital Audio LPCM 2CH
Audio Sampling Rate Up to 96kHz
Stereo Input/Output Level 2 Vrms ± 0.2
Resolution 480i~1080p@50/60, 1080p@24, 4K x
2K (3840x2160/4096x2160@30Hz)
ESD Protection Human body model:
±8kV (air-gap discharge)
Power Supply 24V/ 3.75A DC (US/EU standards, CE/FCC/
UL certied)
Dimensions 215mm(W) x 172.5mm(D) x 46mm(H)
Weight 1060 g
Chassis Material Aluminum
Silkscreen Color Black
Operating Temperature Operating from 0°C ~ 40°C
Storage Temperature -20˚C ~ 60˚C / -4 ˚F ~ 140 ˚F
Relative Humidity 20 ~ 90% RH (non-condensing)
Power Consumption 59.4W