GGM gastro WAEBJ1 User manual

WAFFLE MAKER
USER’S MANUAL

Thank you for buying our product, in order to ensure safe used, please read the
Instructions before using and keep it for reference.
Safety Precautions
The following safety precautions must be observed when using this product:
1. Please read the relevant instructions carefully before using this product.
2. Do not share the same power source with other high-power appliances to avoid excessive
power load and other dangers.
3. The surface temperature of this product is very hot after working or just using. Burns may
be caused by contact with hot parts.
4. If children are nearby, use the product with extra care. Do not leave the product to
children alone.
5. Do not allow this product to be used unattended.
6. Do not touch the power cord with sharp objects and high-temperature surface to avoid
damage to the power cord.
7. Frequently check whether the power cord and plug are damaged. Once any signs of
damage are found, please stop using immediately and ask for professional maintenance or
replacement.
8. After use, press the power button to close and pull out the plug from the socket to avoid
leakage or shock due to aging insulation
9. The product shall be installed in a dry, clean and ventilated place; And put the product in a
horizontal and smooth position
10. For the sake of safety, the product must be reliable grounding, and install leakage switch to
ensure personal safety, otherwise not to use.
11. Please unplug the power cord and remove, check or clean the product after it has cooled
completely.
12. Do not plug or unplug the power cord in wet hands to avoid electric shock.
Note for the First Time Use
1. Please read the Instructions carefully.
Model
Dimensions(mm)
Voltage（v）
Power （w）
Hz
WAEBJ1
440*305*225
230
2000
50-60
WAEBJ2
630*420*225
230
2000+2000
50-60

2. Please check if all switches are in off position.
3. Please check all the accessories are complete.
4. Please tear up the protective film on the surface of the product, then clean the rust oil
wipe on surface of the product with a dry cloth.
5. The supply voltage must match the voltage specified on this machine.
6. The smoke is normal when first time turn on the machine, it’s the oil inside the machine
which to protect it become rusting.
Operating Steps
1.Mix the ingredients. 2.Turn on the switch , adjust the
Temperature to 160-180℃.
3. 3. 3.Wait for the indicator light to go out. 4.Put the pulp to the non-stick plate.
NON-stick plate.
5.Turn the machine and adjust the timer 6.Turn on the machine and take out
to 3 minutes. the waffle.
Care and Cleaning
1. Unplug the power cable and ensure that the product is cooled
completely, then cleaning and collection.

2. Cleaning cooking surface with a soft cloth or sponge dampened in a mild detergent.
3. Please don’t use wire brush, stiff brush or other corrosive liquids to clean it, avoiding
damage the surface coating.
4. If batter adheres to plates, simply pour a little cooking oil onto the baked batter and let
stand approximately 5 minutes, allowing batter to soften for easy removal.
5. Never use an abrasive cleanser or harsh pad.
6. Never clean the product by sprinkling water and immersed in water.
Tips and Maintenance
1. Pan MUST be open when pre-heating (if closed the temperature inside is much more
higher than open, long time high temperature is not good for Teflon coating), 160-180℃is
our best temperature during the test.
2. If machine is an additional product to your shop, please keep temperature under 80℃
when no customers, it’s better to turn off the machine if there’s long time no customer.
3. If machine is main product in your shop, 3-4 units machine is suggested, they can be
replaced every two hours.
4. Use bamboo stick to take out cone, do not use any metal tool. If there’s black dots appear
on the pan surface, it can be judged that the caramel with Teflon coating is falling off
(Caramel is when oil and sugar do not clean for a long time, it cannot be seen by visual
inspection, it turns into black dots and stick on waffles) The best solution is changing
heating pan.
5. Use wet towel to clean the pan, if anything difficult to wipe off, use professional kitchen
glue brush, put some water in holes, heat the water a bit, it’s easier cleaning, but do not let
water go inside of machine.
6. Do not brush oil on pan directly, you can add oil inside your recipe or waffle mix, but do not
add too much oil, or it will get infiltrate and heater may get burnt.
7. Do not use corrosive cleanser to clean the waffle pan.
This machine shell must be grounded and ensure safety, thank you for your
cooperation.

Notice
The products which electric
power is over 1kw must plug a
properly (grounded) individual
receptacle.
It could result in
fire by ignition.
Do not cover the product with
a cloth or plastic bag while you
are using it.
It could result in
fire.
Ensure to unplug the product
while you don't use it.
It could result in
fire or electric
shock.
Do not touch the product with
wet hands.
It could result in
electric shock.
Never clean the machine by
sprinkling water.
It could result in
electric shock or
product damage.
Do not use the product
outside in the rain or wet area.
It could result in
electric shock.
Use the product in a light
place.
It could result in
accident or burn if
you use it in a dark
room.
Do not use the product
near flammable gas or Do not
use the
It could result in
explosion or fire.

Fault
Reason
Method
Turn on the power，but the green light
doesn't work
1.There is no power at the outlet
2.The power cord contacts bad
terminal is loose
3.The green light was burnt out
1.Check the socket for power
2、Fastening the power cord and
terminals wiring
3.Replace the green light
The yellow light didn't go out and the
temperature of the machine rose is
out of control
1.The thermostat doesn't work
1.Replace the thermostat
The indicator light is not on, but the
temperature control is normal
1.The indicator light has bad
contact
2.The indicator light was burnt out
1.Fastening the wires
2.Replace the indicator light
The yellow light is on but not heated
1.Wrong connection of indicator
light
2.The heating tube was burnt out;
1.Rewire according to correct
wiring
2.Replace the heating tube
The green light is on, the yellow light is
off, but the machine is not heated
Thermostat was damaged
Replace the thermostat
Yellow indicator light is always on, the
lower plate is not hot, the upper plate
has been heating and the temperature
is ultra high
1.The connection of lower board
heating pipes is loose
2.The lower heating tube is
damaged
1.Check the connection of
heating pipes
2.Replace the lower heating
tube
The yellow light is on and the
temperature of the lower plate is
normal，but the upper plate is not hot.
1.The connection of upper
heating pipes is loose
2.The top heating tube is burnt
out
1.Check the connection of
heating wires
2.Replace the lower heating
tube
Plug in the power and turn on the
thermostat，then caused switch trip
1.The internal wiring is loose and
the belt parts touch the metal
shell;
2.Short circuit is caused by
heating pipe burning
1.Check the internal wiring of
the machine and tighten it
2.Replace with a new heating
tube

Inspection of general faults
WAEBJ1
No.
Material no
Spare parts name
1
Up cover
2
Handle fixed board
3
Element press board
4
3050035
Up element
5
3040012
Connect terminal
6
3080195
Flexible tube
7
3040030
Wire clip
8
Down cover
9
3030002
Wire
10
Base
11
3040041
Foot
12
Bottom sealing board
13
3020031
5 minute timer
14
3020070
Timer knob
15
3020053
Thermostat knob
16
3020037
300℃dial
17
3020002
300℃thermostat
18
3091248
Support column
19
3040001
Switch
20
3040025
Light
21
3050035
Down element
22
3070383
Down molding board
23
3070383
Up molding board
24
3080380
Handle

WAEBJ2
No.
Material no
Spare parts name
1
Up cover
2
Handle fixed board
3
Element press board
4
3050035
Up element
5
3040012
Connect terminal
6
3080195
Flexible tube
7
3040030
Wire clip
8
3030002
Wire
9
3040041
Foot
10
Bottom board
11
3040001
Switch
12
3040025
Light
13
3020002
Thermostat
14
3020037
300℃dial
15
3020053
Thermostat knob
16
3020070
Timer knob
17
3020031
5 minute timer
18
3050035
Down element
19
Base
20
3091248
Support column
21
Down cover
22
3070383
Down molding board
23
3070383
Up molding board
24
3080380
Handle

GGM Gastro International GmbH
Weinerpark 16, 48607 Ochtrup
www.ggmgastro.com