Ghost Controls AXUR User manual

WHAT IS INCLUDED IN YOUR AXUR KIT:
SPECIFICATIONS:
NOTE: The receiver is designed to allow the use of Ghost Controls®Wireless accessories, such as our transmitters and keypad to
work with other opener and operator systems that accept dry contact inputs to control the system (ex. doorbell button).
THE RECEIVER HAS TWO SOLID STATE RELAY OUTPUTS:
■CYCLE (blue and green wires): This is a momentary/pulsed output. The relay is turned on momentarily for about half second
then turns off upon receiving a valid “cycle” command from a Ghost Controls®wireless device. It is to be connected to the input of
the opener system that can open, close and stop the gate or access control system.
■FREE-EXIT/OPEN (white and green wires): This is a latching, toggle ON/OFF output. The relay is toggle ON/OFF upon
receiving a valid “open” command, such as “PartyMode®, from a Ghost Controls®wireless device. It is to be connected to the input
of the opener system that when activated will keep it OPEN.
POWER INPUT: 9-24 VDC or VAC, 15 mA
OUTPUTS: Solid state relay’s Max. 24VAC/DC @ 100mA max load
EXTENDABLE ANTENNA USING STANDARD COAX CABLE WITH COAX CABLE COUPLER
WEATHER RESISTANT FOR OUTDOOR INSTALLATION
DETERMINING YOUR SYSTEM REQUIREMENTS:
NOTE: Refer to your system instruction manual for details.
■Locate and make sure that it has 9-24VAC or VDC power supply available. Typical
system will have either 12 or 24V available. The RED WIRE of the receiver will be
connected to the positive terminal of the power supply and the BLACK WIRE of
the receiver will be connected to the negative terminal of the power supply.
■Locate the input that controls its movement (open, close, and stop). Typically, a
momentary activation with a jumper wire would “CYCLE” the opener/operator
to each movement (open, stop, close, stop, open...). Usually, it is labeled
“CYCLE”, “Pushbutton” or something similar. The BLUE WIRE from the receiver
will be connected to this input and the GREEN WIRE is connected to the COM
or COMMON terminals.
■Locate the input that when activated (shorted to COMMON) will keep the gate
or access control system open. When the terminal is shorted to COMMON
the gate or access control system cannot be closed. Usually, it is labeled “open”,
“free-exit”, “fire-department” or something similar. The WHITE WIRE from the
receiver will be connected to this input and the GREEN WIRE is connected to
COM or COMMON. NOTE: Using this input is optional, this input allows the use
of Ghost Controls®PartyMode®and open-only wireless devices.
AXUR UNIVERSAL RECEIVER
INSTRUCTIONS
RED = POSITIVE POWER SUPPLY
TEST: red and black wires to
mke sure getting enough
power supply of 9-24v
WIRELESS KEYPAD
RECEIVER
5 BUTTON TRANSMITTER
BLK = NEGATIVE POWER SUPPLY
BLUE = CYCLE INPUT
GREEN = COM OR COMMON
WHITE = OPEN INPUT

MOUNTING THE RECEIVER:
NOTE: Cable length is 10 feet and SHOULD BE MOUNTED WHERE ANTENNA IS ABOVE THE FENCE OR POST
FOR MAXIMUM RANGE (as shown below). For exterior applications we recommend running receiver cable through PVC
conduit to protect cable from damage. DO NOT run AC wiring through the conduit. Receiver range varies depending on
external interference, weather, and topography of the area you live in.
DRILL HOLE IN POST AND MOUNT RECEIVER ANTENNA FACING UP, WITH THE INCLUDED SCREW.
PROGRAMMING THE RECEIVER:
WARNING: The operator/opener may move during programming. Stay clear of its moving path.
REMOVE RECEIVER COVER BY UNSCREWING THE 4 SCREWS ON THE FRONT COVER.
COMPLETED VIEW OF MOUNTED RECEIVER
MOUNTING RECEIVER TO THE POST

STEP 1. UNDERSTANDING THE LEDS UNDER THE COVER
RED LED:
■Blinking = A Ghost Controls®signal is received (the signal may or may not have been programmed to the receiver)
■Solid = Receiver is in LEARN mode
YELLOW LED:
■One Blink = A valid Ghost Controls®signal is received and the “cycle” relay is momentarily activated for half a second
■OFF = “CYCLE” relay is off
GREEN LED:
■ON = A valid PartyMode®or exit Ghost Controls®signal is received and the “OPEN” relay is on/activated
■OFF = “OPEN” relay is off
STEP 2. HOW TO TEACH YOUR RECEIVER TO LEARN THE NEW REMOTE TRANSMITTER
1. Press and hold the LEARN button on receiver until the unit beeps and the RED LED stays on.
2. Release the LEARN button. The RED LED will stay lit to indicate that it is in LEARN mode and waiting for the signal from the
remote transmitter.
3. Press and hold the or button on the GHOST CONTROLS®remote transmitter until you hear a beep and the RED LED
on the receiver turns o. The transmitter is now programmed into the receiver and controls the access control system or gate.
4. Confirm that the transmitter activate the CYCLE relay by observing that the YELLOW LED blinks once with each press of the
transmitter.
5. The FREE-EXIT/OPEN output is automatically programmed.
6. Confirm that the FREE-EXIT/OPEN output is operational:
a. Press and hold the button on the transmitter until the RED LED on the transmitter stays lit.
b. Press the transmitter’s button in # 3 above.
c. The receiver’s FREE-EXIT/OPEN output and GREEN LED should turn ON and stay ON.
d. Repeat a and b above to turn the receiver’s FREE-EXIT/OPEN output and GREEN LED OFF.
IMPORTANT
If you have a wireless keypad or additional transmitters, you can now use this programmed/learned remote to program them.
PLEASE REFER TO THE KEYPAD OR TRANSMITTER MANUALS FOR DETAILS OR OUR WEBSITE
GHOSTCONTROLS.COM.

Made in China, AXURIM | REV 0420
©2020 GHOST CONTROLS®
WARNING: This product can expose you to chemicals including
lead, which is known to the State of California to cause cancer.
For more information, go to www.P65Warnings.ca.gov.