Giant Alarm System BP1064L2 User manual

BP1064L2 Bluetooth Module operating instruction
Works in the 2.4GHz (2402MHz~2480MHz) ISM band
79 channels for Bluetooth V5.0(BR/EDR) without BLE mode
Modulation type: GFSK, π/4-DQPSK, 8DPSK for Bluetooth V5.0 (BR/EDR)
Data Rate: 1/2/3Mbps for Bluetooth V5.0 (BR/EDR)
端口定义
J13
J28
Pin1
+5V
Pin1
+5VM
Pin2
+3.3VA
Pin2
DGND
Pin3
-4V
Pin4
DGND
Pin5
DGND
Pin6
CHGND
Pin7
CHGND
J27
Pin8
+3.3V
Pin1
+5VM
Pin9
+V_LED
Pin2
DGND
Pin10
+15V
Pin3
+V_LCD
Pin11
-15V
Pin12
AGND
J1 AUDIO IN
Pin13
CH1_HIZ
Pin1
AGND
Pin14
DIP1_4
Pin2
MUSIC 1 INPUT
Pin15
CHGND
Pin3
CH4 INPUT
Pin16
CH1_CLIP
Pin4
CH3 INPUT
Pin17
SIG_LED1
Pin5
CH2 INPUT
Pin18
CH1_PRIORITY
Pin19
MAIN_POWER
J2
Pin20
MAIN_MUTE
Pin1
DIP1_4
Pin21
M74HC165_S/_L
Pin2
CHGND
Pin22
M74HC165_CK
Pin3
+15V INPUT
Pin23
M74HC165_QH
Pin4
CHGND
Pin24
AGND
Pin5
-15V INPUT
Pin25
CH1_AMP
Pin6
AGND
Pin26
AGND
Pin7
CH1 INPUT
Pin27
CHGND
Pin8
CHGND
Pin28
CHGND

PCB function
1、
PCBA includeINPUT1/INPUT2/INPUT3/INPUT4/MUSIC1 Analog signal
input preamplification
2、
Bluetooth audio signal decoding and amplification circuit
3、
Mixed audio signal amplifier circuit
4、
Sine wave/clipping signal LED indicating control circuit
5、
TONE/HPF/MASTER VOLUME CONTROL
6、
USB MP3 Audio decoder control circuit

For USA
FCC Statement
FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247
PCB antenna , Antenna gain 2.81dBi
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
We will retain control over the final installation of the modular such that compliance of the end
product is assured. In such cases, an operating condition on the limit modular approval for the
module must be only approved for use when installed in devices produced by a specific
manufacturer. If any hardware modify or RF control software modify will be made by host
manufacturer,C2PC or new certificate should be apply to get approval,if those change and
modification made by host manufacturer not expressly approved by the party responsible for
compliance ,then it is illegal.
FCC Radiation Exposure Statement
The modular can be installed or integrated in mobile or fix devices. This modular cannot be
installed in any portable device if without any further certify include C2PC with SAR. This modular
complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This modular must be installed and operated with a minimum distance of 20 cm
between the radiator and user body.
If the FCC identification number is not visible when the module is installed inside another device,
then the outside of the device into which the module is installed must also display a label

referring to the enclosed module. This exterior label can use wording such as the following:
“Contains Transmitter Module FCC ID: 2AUHE-BP1064L2 Or Contains FCC ID: 2AUHE-BP1064L2 ”
When the module is installed inside another device, the user manual of the host must contain
below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference;
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
2. Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
The devices must be installed and used in strict accordance with the manufacturer's instructions
as described in the user documentation that comes with the product.
Any company of the host device which install this modular with limit modular approval should
perform the test of radiated & conducted emission and spurious emission, etc. according to FCC
part 15C : 15.247 and 15.209 & 15.207 ,15B Class B requirement, Only if the test result comply
with FCC part 15C : 15.247 and 15.209 & 15.207 ,15B Class B requirement，then the host can be
sold legally.
For Canada
IC STATEMENT
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS)
d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis

aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interférences.
(2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer
un fonctionnement indésirable de l'appareil.
IC Radiation Exposure Statement
The modular can be installed or integrated in mobile or fix devices only. This modular cannot be
installed in any portable device .
This modular complies with IC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. This modular must be installed and operated with a minimum distance of
20 cm between the radiator and user body. Cette modulaire doit être installé et utilisé à une
distance minimum de 20 cm entre le radiateur et le corps de l'utilisateur.
If the IC number is not visible when the module is installed inside another device, then the
outside of the device into which the module is installed must also display a label referring to the
enclosed module. This exterior label can use wording such as the following: “Contains IC:
6132C-BP1064L2”
when the module is installed inside another device, the user manual of this device must contain
below warning statements;
1. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
2. Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS)
d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis
aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interférences.
(2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de
provoquer un fonctionnement indésirable de l'appareil.
The devices must be installed and used in strict accordance with the manufacturer's instructions
as described in the user documentation that comes with the product
This device has been designed to operate with the antenna listed below, and having a peak gain
of 2.81dBi @ 2.4GHz,, Antennas not of the same type and having a higher gain specified above
are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.
Model: BP10xx_F