55000093-1
1. Turn the thermostat dial counterclockwise to the lowest setting.
2. Slide the “ON/OFF” switch located on the gas control to the “OFF” position.
3. Turn OFF all electric power to the appliance if service is to be performed.
A. This appliance is equipped with an ignition device
which automatically lights the pilot.
DO NOT TRY to light the pilot by hand.
B. BEFORE operating smell all around the appliance
area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do not use any
phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
1. STOP! Read the safety information above (to the left)
on this label.
2. Slide the “ON/OFF” switch located on the gas control
to the “OFF” position.
3. Turn OFF all electric power to the appliance.
4. Turn the thermostat dial counterclockwise
to the lowest setting.
5. This appliance has an automatic spark ignition system.
DO NOT attempt to light the pilot by hand.
6. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor.
If you smell gas, STOP! Follow “B” in the safety
information above (to the left) on this label.
If you don’t smell gas, go to the next step.
7. Turn ON electric power to the appliance.
8. Slide the “ON/OFF” switch located on the gas control
to the “ON” position.
9. Turn the thermostat dial clockwise
to the desired setting.
10. If the appliance will not operate, follow the instructions
“To Turn Off Gas To Appliance” and call your service
technician or gas supplier.
C. Use only your hand to slide the gas control switch or
turn the thermostat dial. Never use tools. If the switch
or dial will cannot be moved by hand, don’t try
to repair it, call a qualified service technician.
Force or attempted repair may result in a fire or
explosion.
D. DO NOT use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of
the control system and any gas control which
has been under water.
A. Cet appareil est muni d’un dispositif d’allumage qui allume
automatiquement la veilleuse.
NE TENTEZ PAS d’allumer la veilleuse manuellement.
B. AVANT DE FAIRE FONCTIONNER, reniflez tout autour de
l’appareil pour déceler une odeur de gaz. Reniflez près du
plancher, car certains gaz sont plus lourds que l’air et
peuvent s’accumuler au niveau du sol.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• NE PAS TENTER d’allumer d’appareil.
• NE TOUCHEZ à aucun interrupteur ; ne pas vous servir
des téléphones se trouvant dans le bâtiment.
• Appelez immédiatement votre fournisseur de gaz
depuis un voisin. Suivez les instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur,
appelez le service des incendies.
C. Ne glissez le commutateur ou tournez le bouton du
contrôle au gaz qu’à la main ; ne jamais utiliser d’outil.
Si le commutateur ou le bouton reste coincé,
ne tentez pas de le réparer ; appelez un technicien qualifié.
Le fait de forcer ou de le réparer peut déclencher
une explosion ou un incendie.
D. N’UTILISEZ PAS cet appareil s’il a été plongé dans l’eau,
même partiellement. Faites inspecter l’appareil par un
technicien qualifié et remplacez toute partie du système de
contrôle et toute commande qui ont été plongés dans l’eau.
1. ARRÊTEZ ! Lisez les instructions de sécurité sur
la portion supérieure (à gauche) de cette étiquette.
2. Glissez le commutateur “ON/OFF” situé sur le contrôle
au gaz à la position “OFF”.
3. Coupez l’alimentation électrique de l’appareil.
1. Tournez le bouton d’ajustement de température dans le sens antihoraire jusqu’à la position la plus basse.
2. Glissez le commutateur “ON/OFF” situé sur le contrôle au gaz à la position “OFF”.
3. Coupez l’alimentation électrique de l’appareil s’il faut procéder à l’entretien.
4. Tournez le bouton d’ajustement de température
dans le sens antihoraire jusqu’à la position
la plus basse.
5. Cet appareil est muni d’un dispositif d’allumage qui allume
automatiquement la veilleuse.
NE TENTEZ PAS d’allumer la veilleuse manuellement.
6. Attendre cinq (5) minutes pour laisser échapper tout le gaz.
Reniflez tout autour de l’appareil, y compris près du plancher,
pour déceler une odeur de gaz. Si vous sentez une odeur
de gaz, ARRÊTEZ ! Passez à l’étape B des instructions de
sécurité sur la portion supérieure (à gauche) de cette étiquette.
S’il n’y a pas d’odeur de gaz, passez à l’étape suivante.
7. Mettez l’appareil sous tension.
8. Glissez le commutateur “ON/OFF” situé sur le contrôle
au gaz à la position “ON”.
9. Tournez le bouton d’ajustement de température dans
le sens horaire jusqu’au réglage désiré.
10. Si l’appareil ne se met pas en marche, suivez les instructions
intitulées « Comment couper l’admission de gaz de l’appareil »
et appelez un technicien qualifié ou le fournisseur à gaz.
HOT
VERY
HOT
A
B
C
LOW
ON
OFF
STATUS
Switch shown in
“ON” position
Thermostat dial
FOR YOUR SAFETY READ BEFORE OPERATING
OPERATING INSTRUCTIONS
POUR VOTRE SÉCURITÉ LISEZ AVANT DE METTRE EN MARCHE
INSTRUCTIONS DE MISE EN MARCHE
COMMENT COUPER L’ADMISSION DE GAZ À L’APPAREILTO TURN OFF GAS TO APPLIANCE
WARNING: If you do not follow these instructions exactly,
a fire or explosion may result causing property damage, personal injury or loss of life.
AVERTISSEMENT: Quiconque ne respecte pas à la lettre les instructions dans la présente notice
risque de déclencher un incendie ou une explosion entraînant des dommages, des blessures, ou la mort.
Commutateur illustré
à la position «ON»
Bouton
d’ajustement
de température
HOT
VERY
HOT
A
B
C
LOW
ON
OFF
STATUS
ting. To maximize the efficiency of this water heater
ated. “Stacking” is the result of increased cycling of