GIGA-BYTE TECHNOLOGY MZBSWAI User manual

MZBSWAI
Intel®Celeron®Processor N3150
User's Manual
Rev. 1001

Copyright
©2015 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE
without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
Documentation Classications
In order to assist in the use of this product, GIGABYTE provides the following types of documentations:
For detailed product information, carefully read the User's Manual.
For product-related information, check on our website at:
http://www.gigabyte.com

- 3 -
Table of Contents
Box Contents...................................................................................................................4
MZBSWAI Motherboard Layout.......................................................................................5
Block Diagram .................................................................................................................7
Chapter 1 Hardware Installation .....................................................................................8
1-1 Installation Precautions.................................................................................... 8
1-2 ProductSpecications...................................................................................... 9
1-3 Installing the Memory..................................................................................... 11
1-3-1 Installing a Memory ...............................................................................................11
1-4 Back Panel Connectors.................................................................................. 12
1-5 Internal Connectors........................................................................................ 13
Chapter 2 BIOS Setup ..................................................................................................24
2-1 The Main Menu .............................................................................................. 26
2-2 Advanced Menu ............................................................................................. 28
2-2-1 SuperIOConguration...........................................................................................29
2-2-1-1 SerialPortConguration ........................................................................................30
2-2-1-2 ParallelPortConguration......................................................................................31
2-2-2 Hardware Monitor ..................................................................................................32
2-2-3 S5 RTC Wake Settings...........................................................................................33
2-2-4 CPUConguration..................................................................................................34
2-2-4-1 CPU Information.....................................................................................................35
2-2-5 SATAConguration.................................................................................................36
2-2-6 OS Selection...........................................................................................................37
2-3 Chipset Menu................................................................................................. 38
2-4 Security Menu ................................................................................................ 40
2-4-1 Secure Boot menu..................................................................................................41
2-4-1-1 Key Management ...................................................................................................42
2-5 Boot Menu...................................................................................................... 43
2-6 Save & Exit Menu........................................................................................... 44

- 4 -
Box Contents
Motherboard
One SATA power ables
 TwoI/OShield(Standard44.45mm/Low-Prole25.54mm)
One Screw
•The box contents above are for reference only and the actual items shall depend on the product package you obtain.
The box contents are subject to change without notice.
•The motherboard image is for reference only.

- 5 -
MZBSWAI Motherboard Layout
12 3 4 56 7 8 9
10
12
13
14
15
16
17
18
19202122232425
26
27
28
29
30
31
32
33
11

- 6 -
Item Code Description
1 MIC_IN Audio Mic In port
2 LINE_OUT Audio Line Out port
3 VGA VGA prot
4 HDMI HDMI port
5 CLR_CMOS Clear CMOS jumper
6 USB3_2 USB 3.0 ports
7 USB3_1 USB 3.0 ports
8 LAN RJ45 LAN port
9 DC_IN DC In power connector
10 ATX_19V 2 pin power connector
11 BAT_CON Battery cable connector
12 CPU_FAN CPU fan connector
13 SATAIII_0/SATAIII_1 SATA 6Gb/s cable connectors
14 SATA_PWR Hard disk power connector
15 LCD_VCC LVDS Drive voltage jumper
16 FPD_PWR LVDSpowerselectjumper(12V/19V)
17 SYS_FAN System fan connector
18 SYS_PANEL Front panel header
19 MS_SW Monitor power switch header
20 LVDS LVDS connector
21 FPD Flat Panel Display connector
22 BL_SW Back light brightness switch
23 FUSB2_1 USB 2.0 header
24 SO_DIMM DDR3 SO-DIMM slot
25 FUSB2_2 USB 2.0 header
26 COM1 Serial port cable connector
27 LPT Parallel port header
28 CPU Intel Celeron® Processor N3150, SoC
29 M2E PCI Express M.2 connector
30 PCIE1X PCI Express x 1 slot
31 DMIC_CON Digital Mic connector
32 FP_AUDIO Front audio header
33 SPKR Speaker cable connector

- 7 -
Block Diagram

Hardware Installation
- 8 -
1-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can
becomedamagedasaresultofelectrostaticdischarge(ESD).Priortoinstallation,carefullyread
the user's manual and follow these procedures:
• Priortoinstallation, do not removeorbreakmotherboard S/N (SerialNumber)stickeror
warranty sticker provided by your dealer. These stickers are required for warranty validation.
• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
• When connecting hardware components to the internal connectors on the motherboard,
make sure they are connected tightly and securely.
• When handling the motherboard, avoid touching any metal leads or connectors.
• Itisbesttowearanelectrostaticdischarge(ESD)wriststrapwhenhandlingelectronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist
strap,keepyourhandsdryandrsttouchametalobjecttoeliminatestaticelectricity.
• Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
• Before unplugging the power supply cable from the motherboard, make sure the power
supply has been turned off.
• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
• Before using the product, please verify that all cables and power connectors of your
hardware components are connected.
• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
• Do not place the computer system on an uneven surface
.
• Do not place the computer system in a high-temperature environment.
• Turning on the computer power during the installation process can lead to damage to
system components as well as physical harm to the user.
• If you are uncertain about any installation steps or have a problem related to the use of the
product,pleaseconsultacertiedcomputertechnician.
Chapter 1 Hardware Installation

- 9 -
Hardware Installation
1-2 ProductSpecications
CPU Intel®Celeron®Processor N3150, SoC, Quad Core
L1/L2 cache varies with CPU
Memory 1 x SO-DIMM slots support 1.35V DDR3L 1600MHz
Support up 8GB
Audio Realtek®ALC887 HD Audio Codec
2 channel
LAN 1 x Realtek RTL8111HS-CG GbE controller supports 10/100/1000 Mbps
Expansion Slots 1 x PCI Express x1 slot
1xM.2slot(PCIExpressInterface):
* Socket 3
* M key
Onboard
Graphics
Build in Intel®processor
1D-subVGAPort,1HDMIPort,1LVDS18bit/24bit(1920x1080)
Storage Interface 2 x SATA 6Gb/s connector
USB 4xUSB3.0port(backpanel)
3 x USB 2.0 headers (3 additional ports via the USB brackets connected to the
internalUSBheaders)
Internal
Connectors
1 x 2-pin power connector
2 x SATA 6Gb/s connector
1 x SATA HDD power connector
1 x CPU fan header
1 x System fan header
1 x System panel header
1 x Back Light Brightness header
1 x Audio header
3 x USB 2.0 headers
1 x LVDS connector
1 x FPD connector
1 x DMIC header
1 x Serial port cable connector
1 x Parallel port cable header
1 x Speaker cable connector
Back Panel
Connectors
1 x DC-IN
1 x RJ-45 port
1 x HDMI port
4 x USB 3.0 port
1 x VGA port
1 x Audio MIC In
1 x Audio Line Out
I/O Controller Nuvoton NCT5526D chip

Hardware Installation
- 10 -
Hardware
Monitor
CPU temperature detection
CPU/System fan speed control
* Whether the CPU/system fan speed control function is supported will depend on
the CPU/system cooler you install.
BIOS AMI BIOS
Form Factor Thin Mini ITX Form Factor; 170CM x 170CM
GIGABYTE reservesthe right tomakeany changesto the product specicationsandproduct-related
information without prior notice.

- 11 -
Hardware Installation
1-3 Installing the Memory
Read the following guidelines before you begin to install the memory:
•Make sure that the motherboard supports the memory. It is recommended that memory of the
same capacity, brand, speed, and chips be used.
•Always turn off the computer and unplug the power cord from the power outlet before installing
the memory to prevent hardware damage.
•Memory modules have a foolproof design. A memory module can be installed in only one
direction. If you are unable to insert the memory, switch the direction.
1-3-1 Installing a Memory
Installation Step:
Step 1. Align the memory with the SO-DIMM module and insert the SO-DIMM memory module into the
SO-DIMM slot.
Please note that memory module has a foolproof insertion design. A memory module can be
installed In only one direction.
Step2. Pushthememoryandseatitrmly.
Step 3. Reverse the installation steps when you wish to remove the SO-DIMM module.
2
1

Hardware Installation
- 12 -
1-4 Back Panel Connectors
DC Power Jack
Connect the DC power to this port.
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following
describes the states of the LAN port LEDs.
USB 3.0 Port
The USB port supports the USB 3.0 specification. Use this port for USB devices such as a USB
keyboard/mouse,USBprinter,USBashdriveandetc.
HDMI Port
TheHDMI(High-DenitionMultimediaInterface)providesanall-digitalaudio/videointerfaceto
transmit the uncompressed audio/video signals and is HDCP compliant. Connect the HDMI
audio/video device to this port. The HDMI Technology can support a maximum resolution of
1920x1080p but the actual resolutions supported depend on the monitor being used.
Video Port
The video in port allows connect to video in, which can also apply to video loop thru function.
Line Out (Front Speaker Out/Green)
ThedefaultLineOut(FrontSpeakerOut)jack.Stereospeakers,earphoneorfrontsurroundspeakers
canbeconnectedtoLineOut(FrontSpeakerOut)jack.
MIC In (Pink)
The default MIC In jack. Microphone cab be connected to MIC In jack.
• When After installing the HDMI device, make sure the default device for sound playback is the
 HDMIdevice.(Theitemnamemaydifferbyoperatingsystem.Refertheguresbelow
 fordetails.),andenterBIOSSetup,thensetOnboardVGAoutputconnecttoD-SUB/
HDMI under Advanced BIOS Features..
• Please note the HDMI audio output only supports AC3, DTS and 2-channel-LPCM
 formats.(AC3andDTSrequiretheuseofanexternaldecoderfordecoding.)
• Whenremovingthecableconnectedtoabackpanelconnector,rstremovethecablefromyour
device and then remove it from the motherboard.
• When removing the cable, pull it straight out from the connector. Do not rock it side to side to
prevent an electrical short inside the cable connector.
Activity LED
Connection/
Speed LED
LAN Port
Activity LED:Connection/Speed LED:
State Description
Orange 1 Gbps data rate
Green 100 Mbps data rate
Off 10 Mbps data rate
State Description
Blinking Data transmission or receiving is occurring
Off No data transmission or receiving is occurring

- 13 -
Hardware Installation
1-5 Internal Connectors
1) SYS_PANEL
2) SATAII_0/SATAII_1
3) FUSB2_1
4) FUSB2_2
5) SPKR
6) FP_AUDIO
7) DMIC_CON
8) FPD
9) FPD_PWR
10) BL_SW
11) LVDS
12) LCD_VCC
13) MON_SW
14) COM1
15) LPT
16) CPU_FAN
17) SYS_FAN
18) ATX_19V
19) BAT_CON
20) CLR_CMOS
Read the following guidelines before connecting external devices:
• First make sure your devices are compliant with the connectors you wish to connect.
• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices.
• After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
1
2
34
5
6
7
8
9
10
12
13
14
15
16
17
18
19
20
11

Hardware Installation
- 14 -
1) SYS_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, and system status indicator on the chassis to this
header according to the pin assignments below. Note the positive and negative pins before connecting
the cables.
The front panel design may differ by chassis. A front panel module mainly consists of power switch,
reset switch, power LED, hard drive activity LED, and etc. When connecting your chassis front
panel module to this header, make sure the wire assignments and the pin assignments are matched
correctly.
PinNo. SignalName Denition
 1 HD+  HardDiskLEDSignalanode(+)
 2 MPD+  PowerLEDSignalanode(+)
 3 HD-  HardDiskLEDSignalcathode(-)
 4 MPD-  PowerLEDSignalcathode(-)
5 GND Ground
 6 PW+  PowerButtonanode(+)
7 RST Reset Button
 8 PW-  PowerButtoncathode(-)
 9 WF_LED  WiactiveLEDSignal
21
109

- 15 -
Hardware Installation
1
7
DEBUG
PORT
G.QBOFM
2) SATAIII_0/SATAIII_1 (SATA 6Gb/s Connectors)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and
SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device.
SATAIII_1
SATAIII_0
PinNo. Denition
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
3/4) FUSB2_1/FUSB2_2 (USB 2.0 Headers)
 TheheadersconformtoUSB2.0/1.1specication.EachUSBheadercanprovidetwoUSBportsviaan
optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.
PinNo. Denition
1 VCC
2 USB-
3 USB+
4 GND
5 No Pin
1
1
9
2
10
5
FUSB2_2
FUSB2_1
FUSB2_1
FUSB2_2
PinNo. Denition
 1 Power(5V)
 2 Power(5V)
3 USB DX-
4 USB DY-
5 USB DX+
6 USB DY+
7 GND
8 GND
9 No Pin
10 NC

Hardware Installation
- 16 -
1
4
5) SPKR (Speaker Cable Connector)
PinNo. Denition
1 Speaker OUT L-
2 Speaker OUT L+
3 Speaker OUT R+
4 Speaker OUT R-
6) FP_AUDIO (Front Panel Audio Header)
 ThefrontpanelaudioheadersupportsIntelHighDenitionaudio(HD)andAC'97audio.Youmayconnect
your chassis front panel audio module to this header. Make sure the wire assignments of the module
connector match the pin assignments of the motherboard header. Incorrect connection between the
module connector and the motherboard header will make the device unable to work or even damage it.
PinNo. Denition
1 MIC_L
2 GND
3 MIC_R
4 -ACZ_DET
5 HPOUT_R
6 F_MIC_JD
7 GND
8 NC
9 F_LINE2
10 F_LINE_JD
1
2
9
10

- 17 -
Hardware Installation
1 5
7) DMIC_CON (DMIC Header)
PinNo. Denition
1 Power
2 DMI DATA
3 GND
4 DMI CLK
5 No Pin
8) FPD (Flat Panel Display Headers)
The FPD is a high-speed interface connecting the output of a video controller in a laptop computer,
computer monitor or LCD television set to the display panel. Most laptops, LCD computer monitors and
LCD TVs use this interface internally.
 TheheadersconformtoFPDspecication.
18
PinNo. Denition
1 BKLT_EN
2 BKLT_PWM
3 BKLT_PWR
4 BKLT_PWR
5 BKLT_GND/Brightness_GND
6 BKLT_GND/Brightness_GND
7 Brightness_Up
8 Brightness_Down

Hardware Installation
- 18 -
9) FPD_PWR (LVDS Power Select Jumper)
1-2 Close: Set to 12V.
2-3Close:Setto19V.(Defaultsetting)
1
1
10) BL_SW (Back Light Switch Header)
The Back Light switch provides the function for screen back light adjustment.
1
2PinNo. Denition
1 BL_DOWN
2 BL_UP

- 19 -
Hardware Installation
11) LVDS (LVDS Connector)
LVDS stands for Low-voltage differential signaling, which uses high-speed analog circuit
techniques to provide multigigabit data transfers on copper interconnects and is a generic interface
standard for high-speed data transmission.
PinNo. Denition
1 +RXO3_C
2 -RXO3_C
3 +RXO2_C
4 -RXO2_C
5 +RXO1_C
6 -RXO1_C
7 +RXO0_C
8 -RXO0_C
9 +RXE3_C
10 -RXE3_C
11 +RXE2_C
12 -RXE2_C
13 +RXE1_C
14 -RXE1_C
15 +RXE0_C
16 -RXE0_C
17 GND
18 LCD_VCC
19 LCD_VCC
20 LCD_VCC
PinNo. Denition
21 NC
22 VCC3
23 GND
24 -LVDS_SENSE
25 GND
26 +RXECLKO_C
27 -RXECLKO_C
28 GND
29 GND
30 GND
31 SCL1
32 SC_BKLT_EN
33 SC_BKLTCTL
34 +RXECLKE_C
35 -RXECLKE_C
36 FPD_19V
37 FPD_19V
38 FPD_19V
39 NC
40 SDA1
1 40
12) LCD_VCC (LVDS Drive Voltage Jumper)
1
1
1-2 Close: Set to 3V.
2-3Close:Setto5V.(Defaultsetting)

Hardware Installation
- 20 -
13) MON_SW (Monitor Power Switch Header)
1
2
PinNo. Denition
1 High: turn on monitor
2 Low: turn off monitor
14) COM1 (Serial Port 1 Cable Connector)
The COM header can provide one serial port via an optional COM port cable. For purchasing the
optional COM port cable, please contact the local dealer.
PinNo. Denition
1 NDCDA-
2 NDSRA-
3 NRXDA-
4 NRTSA-
5 NTXDA-
6 NCTSA-
7 NDTRA-
8 RI-_12V_5V
9 GND
10 NC
1
9
2
10