Gigabyte GD-1704BP User manual

English
Content
Preface
Chpter 1 Installation
Unpacking…………………………………………………….….... 1
Viewing Angle Adjustment………….…………………………….... 1
Interface for Arm Applications……………………………….….... 2
Connecting the Display………….……………………………….... 2
Connecting the AC Power………….…………………………….... 2
Connecting the Audio Cable………….…………………………... 3
Setting Up the LCD Monitor………….…………………………….... 3
Power Management System……….…………………………….... 3
Chpter 2 Display Control
User Controls………………………….…………………………….... 4
Adjusting the Monitor's Display…….…………………………….... 4
Function Description…………….……………………………….... 5
Chpter 3 Technical Informaion
Specifications……………………….…………………………….... 7
Standard Timing Ta
ble…………….………………………………...1 0
Troubleshooting…………………….………………………………...11

Preface
This manual is designed to assist users in setting up and using the LCD Monitor. Information in this
document has been carefully checked for accuracy; however, no guarantee is given to the correctness
of the contents. The information in this document is subject to change without notice. This document
contains proprietary information protected by copyright. All rights are reserved. No part of this manual
may be reproduced by any mechanical, electronic or other means, in any form, without prior written
permission of the manufacturer.
FCC Statement Warning
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instruction, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•Reposition or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced monitor technician for help.
Warning
Use only shielded signal cables to connect I/O devices to this equipment. You are cautioned
that changes or modifications not expressly approved by the party responsible for
comliance could void your authority to operate the equipment.
This device complies with part 15 FCC Rules. Operation is subject to the
following two conditions (1)This device may not cause harmfu interference.
(2)This device must accept any interference received,including interference
that may cause undesired operation.
Canadian DOC Notice
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.

English
Important Safety Instructions
Please read the following instructions carefully. This manual should be retained for future
use.
1. To clean LCD Monitor screen;
-- Power off LCD Monitor and unplug the AC Cord.
-- Spray a non-solvent cleaning solution onto a rag.
-- Gently clean the screen with dampened rag.
2. Do not place the LCD Monitor near a window. Exposing the monitor to rain water,
moisture or sunlight can severely damage it.
3. Do not apply pressure to the LCD screen. Excess pressure may cause permanent
damage to the display.
4. Do not remove the cover or attempt to service this unit by yourself. Servicing of any
nature should be performed by an authorized technician.
5. Store LCD Monitor in a room with a room temperature of -20° ~ 60°C (or -4° ~ 140°F).
Storing the LCD Monitor outside this range could result in permanent damage.
6. If any of the following occurs, immediately unplug your monitor and call an authorized
technician.
* Monitor to PC signal cable is frayed or damaged.
* Liquid spilled into LCD Monitor or the monitor has been exposed to rain.
* LCD Monitor or the case is damaged.
7. Only use the supplied main lead to connect the monitor. For a nominal current up to 6A and
a device weight above 3 kg, a line not lighter than H05VV-F, 3G, 0.75 mm2must be used.

1
Chapter 1
Installation
Installation
Unpacking
Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and
computer. You need a stable and clean surface near a wall power outlet. Make sure that
LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses
very little power, some ventilation is needed to ensure that the Monitor does not become
too hot.
After you unpack the LCD Monitor, make sure that the following items were included in the
box:
;LCD Monitor
;User's Manual
;1.8M Monitor-to-PC VGA Cable
;1.8M Power Cord
;1.8M Stereo Jack Audio Cable
If you find that any of these items is missing or appears damaged, contact your dealer
immediately.
Viewing Angle Adjustment
The LCD Monitor is designed to allow users to
have a comfortable viewing angle. The viewing
angle can be adjusted from -5°to +15° (See fig.
1-1).
Warning
This device complies with part 15 FCC Rules. Operation is subject to the
following two conditions (1)This device may not cause harmfu interference.
(2)This device must accept any interference received,
including interference that may cause undesired operation.
Figure 1-1

2
English
Installation Chapter1
Installation
Interface for Arm Applications
The rear of this LCD display ha s four integrate d 4
mm, 0.7 pitches threaded nuts, as well as four 5
mm access holes in the plastic covering as
illustrated in Figure 1-2. These specifications
meet the VESA Flat Panel Monitor Physical
Mounting Interface Standard
Note : Please using M 4mm x 10mm (L)
screw for this application
Connecting the Display
1. Power off your computer.
2. Connect one end of the signal cable to the
LCD Monitor’s VGA port.
3. Connect the other end of the signal cable to
the VGA port
4. Make sure connections are secure.
Connecting the AC Power
1. Connect the power cord to the LCD
Monitor.(See Fig. 1-4)
2. Connect the power cord to an AC power
source.
Figure 1-2
Figure 1-3
Figure 1-4

3
Chapter 1
Installation
Installation
Connecting the Audio Cable
1. Connect the audio cable to the " LINE OUT "
jack on your PC's audio card or to the front
panel's “AUDIO OUT” jack of your CD ROM
drive. (See Fig. 1-5)
2. Connect the other end of the audio cable to the
LCD Monitor's " LINE IN " jack.
Setting Up the LCD Monitor
1. Make sure the AC power cord is connected to the LCD Monitor.
2. Turn on the LCD Monitor's power switch, located on the bezel of the monitor.
Power Management System
This LCD Monitor complies with the VESA DPMS (version 1.0) Power Management guidelines. The
VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync.
signal.
When the LCD Monitor is in power saving mode, the monitor screen will be blank and the
power LED indicator will light yellow.
Figure 1-5

4
English
Display Control Chapter2
Display Control
User Controls
A brief description and the location of all LCD Monitor function controls and indicators:
Figure 2-1
User Controls
A brief description and the location of all LCD Monitor function controls and indicators:
Power LED will be Green when monitor is on, be amber when in
power saving mode, be dark when monitor in off mode. Power
ON/OFF switch for push to ON and push to OFF(Toggle switch)
Function Menu / Function select (clockwise)
Auto Adjust Activity / Function select (counter-clockwise)
Audio Volume Function / Adjust increase
Audio Mute ON-OFF Selection / Adjust decrease
Adjusting the Monitor's Display
The monitor has four function control buttons to select among functions shown on OSD
menu, designed for easy user-viewing environments.
OSD Function Menu
To access OSD Main menu, simply press one of the
Function Select control buttons, and the menu
diagram will pop up on the screen as shown on Fig.
2-2:
Continue pressing the Function Select buttons to
scroll through the entire menu items ,then press
Adjustment Control buttons to adjust content of
selected item.
Attention
Firmware revision may have been updated into a latest version
while the version number shown on all OSD menus in this manual
will stay as Ver. 1.00.
Figure 2-2

5
Chapter 2 Display Control
Display Control
Function Description
Icon
Function Function Description
Brightness 101 scales of brightness are available to choose from
(0 to 100).
Contrast 101 scales of contrast are available to choose from
(0 to 100). (Digital Input Mode not support.)
H. Position This function let's you adjust the display's horizontal
position(Digital Input Mode not support.)
V. P o s i t i o n This function let's you adjust the display's vertical
position. (Digital Input Mode not support.)
Sharpness
This function let's you select the images sharpness. Five
selections are available. A smoother setting is more
suitable for pictures, while a sharper setting is more
suitable for text.
(Digital Input Mode not support.)
OSD
Transparency
This function let's you set the transparency of the OSD
menu. The transparency is adjustable from 0 to 3. 4
scales are available. (Digital Input Mode not support.)
Phase
A total of 101 scales (0 to 100) are available to adjust the
focus and clarity of the display.
(Digital Input Mode not support.)
Clock
This function carries a frequency-tracking feature that
offers users better stability and clarity. 101 scales (from
-50 to +50) are available on the mode that is currently
running. The adjustable range can be variable in
different modes. This function records the deviated
number of clock period between input timing and
supported timing. The clock value may not be”0” after
Auto Adjustment when the input timing is different from
supported timing. (Digital Input Mode not support.)
Color
Temperature
Push the ( ) button to select a different color
temperature. Please see the diagram below for function
and description.
(Digital Input Mode not support.)
OSD H. Position This function moves the OSD menu window horizontally.
OSD V. Position This function moves the OSD menu window vertically.
Graph / Text
Because the H and V-Frequencies of both 640 x 400
70Hz, and 720 x 400 70Hz, are the same, this function
let's you manually select either 640 x 400 (graphics
mode), or 720 x 400 (text mode).
(Digital Input Mode not support.)

6
English
Display Control Chapter2
Display Control
Icon Function Function Description
Recall The recall function will return all adjusted parameters to
factory preset values.
Language
Eight OSD language options are available:
English, German, French, Spanish, Italian, Japan,
Russian, and Chinese(Traditional), Chinese(simple).
Press the left or right adjustment control button to select
other language.
Auto and Input
Select
Press button ( ) to activate the selected function,
Auto Adjustment (not support in Digital Input Mode),
Use Analog Input or Use Digital Input.
The Auto Adjustment function let you adjust the display
size, clock and phase to obtain the best viewing settings.
This process will take 3 ~ 5 seconds to complete.
Attention : After Auto Adjustment, the display might
display wrong position or size, if it has received a pattern
which has no screen border. You may select either Analog
or Digital Input video when VGA input is available.
Exit Saves the values of this setting and exits the OSD menu
function.
Icon Function Description
9300 CIE coordinated Color Temperature
of 9300°K
Sets the CIE coordinate color
temperature to 9300°K
7500 CIE coordinated Color Temperature
of 7500°K
Sets the CIE coordinate color
temperature to 7500°K
6500 CIE coordinated Color Temperature
of 6500°K
Sets the CIE coordinate color
temperature to 6500°K
User Three colors (Red, Green, Blue) can
be adjusted from the OSD menu
Sets the settings to a by user
defined CIE Temperature.

7
Chapter 3 Technical Information
Technical Information
Specifications
Size 19" (48 cm)
Display Type Active matrix color TFT LCD
Resolution 1280 x 1024
Display Dot 1280 x (RGB) x 1024
Display Area (mm) 376.32 x 301.056 (H x V)
Display Color 16.2M (RGB 6bit + FRC)
Brightness (typical, minimum) 250 cd/m2
Contrast Ratio (typical) 500:1
Response Time (typical) Ta=25°C Tr+Tf=16ms
Lamp Voltage (typical) 700 Vrms
Lamp Current (typical) 7.0 mA rms.
Viewing Angle Vertical:
Horizontal:
-55° ~ +55°
-60° ~ +60°
Display Colors 16.7M with FRC or Dithering
Video
Input Signal Analogue RGB 0.7Vp-p.
Input Impedance 75 Ohm ± 2%
Polarity Positive, Negative
Amplitude 0 - 0.7 ± 0.05 Vp
Multi-mode Supported Horizontal Frequency: 24 ~ 80 KHz
Control
Power switch →On/Off switch with LED indicator