Gigabyte 6GXU User manual

R-14-01-090414
6GXU
USER'S MANUAL
1. Support Dual BIOS.
2. System power on by PS/2 Mouse: First, enable this function
in CMOS Setup, then you can power on the system by
double clicking the right or left button of your PS/2 Mouse.
3. System power on by Keyboard: If your ATX power supply
supports larger than 300 mA 5V Stand-By current
(dependent on the specification of keyboards), you can
power on your system by entering password from the
Keyboard after setting the “Keyboard power on”jumper and
password in CMOS Setup.
4. Modem Ring-On on COM A, COM B.
5. Wake-up on LAN supports (Your ATX power supply must
support larger than 720 mA 5V Stand-By current).
6. Support LDCM

7. CPU Over Voltage Protection.
Pentium

II / III XEON SLOT2 Processor MAINBOARD

REV 1.4 First Edition

6GXU
1
The author assumes no responsibility for any errors or omissions that may
appear in this document nor does it make a commitment to update the
information contained herein.
Other brands and names are the property of their respective owners.
Sound Blaster is a registered trademark of Creative Technology Ltd in the
United States and certain other countries. Sound Blaster-LINK and SB-LINK
are trademarks of Creative Technology Ltd.
Apr 14, 1998 Taipei, Taiwan

Quick Installation Guide
2
I. Quick Installation Guide :
CPU SPEED SETUP
The system bus speed is set to 100MHz. The user can select the system bus
speed and change the DIP SWITCH (SW1) selection to set up the CPU
speed for 400 - 650MHz processor.
M The CPU speed must match with the frequency RATIO. It will cause
system hanging up if the frequency RATIO is higher than CPU's.
SW1: (ON: m / OFF: 5 )
Ratio 1234 Clk 5 6 7 8 PCI Clk
X4 O O XO100 X X X X 33
X4.5 XOXO112 X X OX37.5
X5 OX X O124 XO O X41.3
X5.5 XXXO133 XOX X 44.3
X6 OOOX133 O O O X33
X6.5 XO O X
« Note: We don’t recommend you to setup your system speed to 112, 124
or 133MHz because these frequencies are not the standard
specifications for CPU, Chipset and most of the peripherals.
Whether your system can run under 112, 124 or 133MHz properly
will depend on your hardware configurations: CPU, SDRAM,
Cards, etc.

6GXU
3
1.PentiumII XEON SLOT2 400 / 100MHz FSB
6GXU
INTEL
443GX
PIIX4
Adaptec
AIC-7890
SLOT 2 XEON
ON
OFF SW
1 2 3 4 5 6 78
Main BIOS Backup
BIOS
2.PentiumII XEON SLOT2 450 / 100MHz FSB
3.PentiumIII XEON SLOT2 500 / 100MHz FSB
4.PentiumIII XEON SLOT2 550 / 100MHz FSB
SW
ON
OFF
1
2
3
4
5
6
7
8
SW
ON
OFF
1
2
3
4
5
6
7
8
SW
ON
OFF
1
2
3
4
5
6
7
8

Quick Installation Guide
4
5.PentiumIII XEON SLOT2 600 / 100MHz FSB
6.PentiumIII XEON SLOT2 650 / 100MHz FSB
F For 133MHz Jumper Setting:
6GXU
INTEL
443GX
PIIX4
Adaptec
AIC-7890
1
2
3
JP3
Main BIOS Backup
BIOS
« Note: We don’t recommend you to setup your system speed to 133MHz
because this frequencies is not the standard specifications for
CPU, Chipset and most of the peripherals. Whether your system
can run under 133MHz properly will depend on your hardware
configurations: CPU, SDRAM, Cards, etc.
SW
ON
OFF
1
2
3
4
5
6
7
8
SW
ON
OFF
1
2
3
4
5
6
7
8

6GXU
5
II. Jumper setting :
SPKR : Speaker Connector
6GXU
INTEL
443GX
PIIX4
Adaptec
AIC-7890
Buzzer
1+
PIN FUNCTION
1VCC
2VCC
3Signal
4Signal
Default :
Internal Buzzer
Main BIOS Backup
BIOS
RST : Reset Switch
6GXU
INTEL
443GX
PIIX4
Adaptec
AIC-7890
Open:
Normal
Operation
Short:
For Hardware
Reset System
Main BIOS Backup
BIOS

Quick Installation Guide
6
PWR : Power LED Connector (as 3 steps ACPI LED)
6GXU
INTEL
443GX
PIIX4
Adaptec
AIC-7890
+
PIN FUNCTION
1LED (+)
2LED (-)
3LED (-)
1
Main BIOS Backup
BIOS
HD : IDE Hard Disk Active LED
6GXU
INTEL
443GX
PIIX4
Adaptec
AIC-7890
+
PIN FUNCTION
1LED (+)
2LED (-)
1
Main BIOS Backup
BIOS

6GXU
7
GN : Green Function Switch
6GXU
INTEL
443GX
PIIX4
Adaptec
AIC-7890
Open:
Normal
operation
Short:
Entering
Green
mode
Main BIOS Backup
BIOS
GD : Green LED Connector

Quick Installation Guide
8
6GXU
INTEL
443GX
PIIX4
Adaptec
AIC-7890
+1
PIN FUNCTION
1LED (+)
2LED (-)
Main BIOS Backup
BIOS
SOFT PWR : Soft Power Connector
6GXU
INTEL
443GX
PIIX4
Adaptec
AIC-7890
PIN FUNCTION
1Signal
2GND
Main BIOS Backup
BIOS
IR : Infrared Connector (Optional)