Gigabyte GA-6VXE+ User manual

R-41-04-010117
6VXE+
USER'S MANUAL
1. System power on by PS/2 Mouse: First, enable this function
in CMOS Setup, then you can power on the system by double
clicking the right or left button of your PS/2 Mouse.
2. System power on by Keyboard: If your ATX power supply
supports larger than 300 mA 5V Stand-By current (depends
on the specification of keyboards), you can power on your
system by entering password from the keyboard after setting
the “Keyboard power on” password in CMOS Setup.
3. Supports 3 steps ACPI LED.
4. Modem Ring-On. (COM A , B).
5. Wake-Up on LAN. (The ATX power supply supports larger
than 720 mA 5V Stand-By current)
For Intel Pentium

II / !!! / CeleronTM Processor MAINBOARD
REV. 4.1 Fourth Edition

6VXE+
1
The author assumes no responsibility for any errors or omissions which may
appear in this document nor does it make a commitment to update the
information contained herein.
Third-party brands and names are the property of their respective owners.
Sound Blaster is a registered trademark of Creative Technology Ltd in the
United States and certain other countries. Sound Blaster-LINK and SB-LINK are
trademarks of Creative Technology Ltd.
Jan 17, 2001 Taipei, Taiwan

Quick Installation Guide
2
I. Quick Installation Guide :
CPU SPEED SETUP
The system bus speed is selectable between 66 / 100 / 133MHz. The user can
select the system bus speed from Dip switch SW1 and jumper JP15 , change
the Dip switch SW2 selection to set up the CPU speed for 233 - 800MHz
processor.
Set System Bus Speed
SW1:
CPU JP15 1 2 3 4
66 ON ON OFF OFF ON
75 ON ON ON OFF ON
83 ON ON OFF ON ON
100 ON OFF OFF OFF OFF
112 ON OFF ON OFF OFF
124 OFF OFF OFF ON OFF
133 OFF OFF OFF OFF OFF
140 OFF OFF ON ON OFF
150 OFF OFF ON OFF OFF
The CPU speed MUST match with the frequency RATIO. It will cause
system hanging up if the frequency RATIO is higher than that of CPU.
SW2: DIP SWITCH
FREQ. RATIO 1 2 3 4
X 3 ON OFF ON ON
X 3.5 OFF OFF ON ON
X 4 ON ON OFF ON
X 4.5 OFF ON OFF ON
X 5 ON OFF OFF ON
X 5.5 OFF OFF OFF ON
X 6 ON ON ON OFF
X 6.5 OFF ON ON OFF
X 7 ON OFF ON OFF
X 7.5 OFF OFF ON OFF
X 8 ON ON OFF OFF
X 8.5 OFF ON OFF OFF
X 9 ON OFF OFF OFF
X 9.5 OFF OFF OFF OFF

6VXE+
3


For 133MHz Jumper Setting:
CPU
VIA
82C693
VIA
82C596B
6VXE
1
Pin No. Function
1-2 close For 100 MHz
2-3 close Auto Frequency
1-2-3 open For 133 MHz
JP12
CPU JP15
66 ON
100 ON
133 OFF
JP15


Note: We don’t recommend you to set up your system speed to 75, 83,
112, 124, 140, 150 MHz because these frequencies are not the
standard specifications for CPU, Chipset and most of the
peripherals. Whether your system can run under 75, 83, 112, 124,
140, 150 MHz properly will depend on your hardware
configurations: CPU, SDRAM, Cards, etc.
☞The black part in the picture is the white extruding piece of the
DIP switch.
1. PentiumII /Celeron 233 / 66 MHz FSB
CPU
VIA
82C693A
VIA
82C596B
6VXE
ON
OFF
SW 2
123
4
ON
OFF
SW 1
1234

Quick Installation Guide
4
2. PentiumII /Celeron 266 / 66 MHz FSB
3. PentiumII /Celeron 300/Celeron 300A / 66 MHz FSB
4. PentiumII /Celeron 333 / 66 MHz FSB
5. PentiumII /Celeron 366 / 66MHz FSB
6. PentiumII /Celeron 400 / 66MHz FSB
7. PentiumII /Celeron 433 / 66MHz FSB
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF

6VXE+
5
8. PentiumII /Celeron 466 / 66MHz FSB
9. PentiumII /Celeron 500 / 66MHz FSB
10. PentiumII /Celeron 533 / 66MHz FSB
11. PentiumII /Celeron 566 / 66MHz FSB (Reserve)
12. PentiumII 350 / 100 MHz FSB
13. PentiumII 400 / 100 MHz FSB
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF

Quick Installation Guide
6
14. PentiumII/!!! 450 / 100 MHz FSB
15. PentiumII/!!! 500 / 100 MHz FSB
16. PentiumII/!!! 550 / 100 MHz FSB
17. PentiumII/!!! 600 / 100 MHz FSB
18. PentiumII/!!! 650 / 100 MHz FSB
19. PentiumII/!!! 700 / 100 MHz FSB
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF

6VXE+
7
20. PentiumII/!!! 750 / 100 MHz FSB
21. PentiumII/!!! 800 / 100 MHz FSB
22. PentiumII/!!! 850 / 100 MHz FSB (Reserve)
23. Pentium!!! 533 / 133 MHz FSB
24. Pentium!!! 600 / 133 MHz FSB
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF

Quick Installation Guide
8
25. Pentium!!! 667 / 133 MHz FSB
26. Pentium!!! 733 / 133 MHz FSB


We don’t recommend you to setup your CPU ratio above 8 nth, it
doesn’t support now.
II. Jumper setting :
SPK : Speaker Connector
CPU
6VXE+
VIA
82C693A
VIA
82C596B
+
1
1
+
Pin No. Function
1 VCC
2 NC
3 NC
4 Data
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF
SW2 ON
4 3 2 1 OFF
SW1 ON
4 3 2 1 OFF