Gigabyte GS-SR 113 User manual

GS-SR 113
Rack Mount Server
System
Installation Guide
REV.1.0

GS-SR113 System Installation Guide
i
Contents
1. SAFE, CARE AND REGULATORY INFORMATION 1
2. PREFACE 6
3. INTRODUCTION 7
3.1. FEATURES 7
4. CONTENTS PACKAGE 10
5. SYSTEM INSTALLATION PROCEDURES 11
5.1. CHASSIS REMOVAL 11
5.2. CPU INSTALLATION 12
5.3. HEAT SINK INSTALLATION 14
5.4. MEMORY INSTALLATION 15
5.5. PCI EXPANSION CARD INSTALLATION 16
5.6. AIR FLOW DUCT INSTALLATION 18
5.7. REINSTALL TOP COVER 19
5.8. DOCK HANDLE INSTALLATION 20
5.9. HARD DISK DRIVE INSTALLATION 20
5.10. APPEARANCE OF GS-SR113 22
5.10.1. FRONT VIEW OF GS-SR113 22
5.10.2. REAR VIEW OF GS-SR113 22
5.10.3. LED INDICATOR DESCRIPTION 23
5.11. CONNECTOR ICON DESCRIPTION 25

GS-SR113 System Installation Guide
ii
The author assumes no responsibility for any errors or
omissions that may appear in this document nor does the author
make a commitment to update the information contained herein.
Third-party brands and names are the property of their respective
owners.
Due to the rapid change in technology, some of the specifications might
be out of date before publication of this booklet.

GS-SR113 System Installation Guide
1
1. Safe, Care and Regulatory Information
Important safety information
Read and follow all instructions marked on the product and in the
documentation before you operate your system. Retain all safety
and operating instructions for future use.
 The product should be operated only from the type of
power source indicated on the rating label.
 If your computer has a voltage selector switch, make sure
that the switch is in the proper position for your area. The
voltage selector switch is set at the factory to the correct
voltage.
 The plug-socket combination must be accessible at all
times because it serves as the main disconnecting device.
 All products shipped with a three-wire electrical grounding-
type plug only fits into a grounding-type power outlet. This
is a safety feature. The equipment grounding should be in
accordance with local and national electrical codes. The
equipment operates safely when it is used in accordance
with its marked electrical ratings and product usage
instructions
 Do not use this product near water or a heat source.
 Set up the product on a stable work surface or so as to
ensure stability of the system.
 Openings in the case are provided for ventilation. Do not
block or cover these openings. Make sure you provide
adequate space around the system for ventilation when
you set up your work area. Never insert objects of any kind
into the ventilation openings.
 To avoid electrical shock, always unplug all power cables
and modem cables from the wall outlets before removing
covers.
 Allow the product to cool before removing covers or
touching internal components.

GS-SR113 System Installation Guide
2
Precautions for Products With Laser Devices
Observe the following precautions for laser devices:
 Do not open the CD-ROM drive, make adjustments, or
perform procedures on a laser device other than those
specified in the product’s documentation.
 Only authorized service technicians should repair laser
devices.
Precautions for Products With Modems,
Telecommunications, or Local Area Network
Options
Observe the following guidelines when working with options:
 Do not connect or use a modem or telephone during a
lightning storm. There may be a risk of electrical shock
from lightning.
 To reduce the risk of fire, use only No. 26 AWG or larger
telecommunications line cord.
 Do not plug a modem or telephone cable into the network
interface controller (NIC) receptacle.
 Disconnect the modem cable before opening a product
enclosure, touching or installing internal components, or
touching an uninsulated modem cable or jack.
 Do not use a telephone line to report a gas leak while you
are in the vicinity of the leak.
Federal Communications Commission (FCC)
Statement
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment

GS-SR113 System Installation Guide
3
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Properly shielded and grounded cables and connectors must be
used in order to meet FCC emission limits. Neither the provider
nor the manufacturer are responsible for any radio or television
interference caused by using other than recommended cables
and connectors or by unauthorized changes or modifications to
this equipment. Unauthorized changes or modifications could
void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC part 68 (applicable to products fitted with USA
modems)
The modem complies with Part 68 of the FCC Rules. On this
equipment is a label that contains, among other information, the
FCC registration number and Ringer Equivalence Number (REN)
for this equipment. You must, upon request, provide this information
to your telephone company.
If your telephone equipment causes harm to the telephone
network, the Telephone Company may discontinue your service
temporarily. If possible, they will notify in advance. But, if
advance notice is not practical, you will be notified as soon as
possible. You will be informed of your right to file a complaint
with the FCC.
Your telephone company may make changes in its facilities,
equipment, operations, or procedures that could affect proper
operation of your equipment. If they do, you will be notified in
advance to give you an opportunity to maintain uninterrupted
telephone service.
The FCC prohibits this equipment to be connected to party lines or
coin-telephone service.

GS-SR113 System Installation Guide
4
The FCC also requires the transmitter of a FAX transmission be
properly identified (per FCC Rules Part 68, Sec. 68.381 (c) (3)).
/ for Canadian users only /
Canadian Department of Communications Compliance
Statement
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus as set out in the radio
interference regulations of Industry Canada.
Le présent appareil numérique n'émet pas de bruits
radioélectriques dépassant les limites applicables aux appareils
numériques de Classe B prescrites dans le règlement sur le
brouillage radioélectrique édicté par Industrie Canada.
DOC notice (for products fitted with an Industry
Canada-compliant modem)
The Canadian Department of Communications label identifies
certified equipment. This certification means that the equipment
meets certain telecommunications network protective, operational
and safety requirements. The Department does not guarantee the
equipment will operate to the user satisfaction.
Before installing this equipment, users ensure that it is permissible
to be connected to the facilities of the local Telecommunications
Company. The equipment must also be installed using an
acceptable method of connection. The customer should be aware
that compliance with the above conditions might not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any
repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines and internal

GS-SR113 System Installation Guide
5
metallic water pipe system, if resent are connected together. This
precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.
NOTICE: The Load Number (LN) assigned to each terminal device
denotes the percentage of the total load to be connected to a
telephone loop which is used by the device, to prevent overloading.
The termination on a loop may consist of any combination of
devices subject only to the requirement that the sum of the Load
Numbers of all the devices does not exceed 100.
/ for European users only /

GS-SR113 System Installation Guide
6
2. Preface
This installation guide will assist you in installing all the essential
components for the rack mount server system. For your
protection, please read and understand all of the safety and
operating instructions regarding your Gigabyte Server and retain
for future reference. The procedures in this guidebook assume
that you are a system or network administrator experienced in
installing similar hardware.
Manual Organization:
Chapter 3 “Introduction” provides the basic product information
and the key features of the product.
Chapter 4 “Contents Package” lists the essential hardware
installation components.
Chapter 5 “System Installation Procedure” provides the fully
instructions for configuration hardware to your system.

GS-SR113 System Installation Guide
7
3. Introduction
Welcome to the Gigabyte GS-SR113 Rack mount Server System
Installation Guide. The guidebook provides instructions for
configuration hardware for the GS-SR113 to your system.
In order to get the optimal usage of your server, please pay
attention to the following tips:
 Go through the installation guide carefully before starting the
system installation processes.
 Keep the system away from static and magnetic field.
 Do not apply any cleaning solutions directly to the system.
3.1. Features
The Gigabyte GS-SR113 is an ultra thin, rack-optimized server
that offers superior performance and scalability to your
networking system. It contains the several features that provide
respective performance for your networking solutions. The key
features of the server include:

GS-SR113 System Installation Guide
8
Features Description
Motherboard  GA-8IRXRR-D
Processor Supported  Supports Single Intel P4
Northwood Processor up to 2.20
Ghz and above
 400MHz FSB
BIOS  Award BIOS on 4Mb flash RAM
 Multiple boot options
 Supports user setting for hardware
monitoring
 Support PXE
 DMI 2.0 compliant
Chipset  Intel Brookdale 845 D (MCH+ICH2)
Memory Supported  2*25 degree angle DIMM sockets
 Supports 2 DDR-266 up to 2 GB
 Supports ECC memory module
 No registered DIMM support
Integrated Intel®
Network Adapter
Features
 Dual Intel® 82550PM Ethernet
controllers
 Supports Wake on LAN
 Adapter Fault Tolerance (AFT)
 Adaptive Load Balancing (ALB)
 Fast EtherChannel (FEC)
Intelligent
Management System
 Standard supports IPMI v 1.0 for
system monitoring.
 Integrated Winbond W83910F
BMC chips
Hot Swap Hard Disk
Drive Bays
 1 Easy Swap
 2 IDE ATA100/133 Hot Swap HDD
RAID Supported  Promise PDC 20267 IDE Raid
0,1,10

GS-SR113 System Installation Guide
9
 Dual ATA100 Channels
Mass Storage System  Three low-profile shelves for hot-
swappable drives
 One slim type flexible FDD drive
 One slim type CD-ROM drive
System Form Factor  1U, ultra thin, rack-optimized
design
System Dimensions  19” W*23” D*1.74” H
I/O expansion slots  4 full-length 32bit/33 MHz PCI slots
Built-in I/O ports  One Floppy Port (up to 2.88MB)
 One 25pin Parallel Port (EPP/ECP)
 Two 9pin 16550 based serial Ports
 4 USB ports
 One standard 15pin VGA
connector
 Two RJ45 LAN ports
 P/S 2 Keyboard and Mouse
Connectors
Power supply  250W maximum continuous
required power
Operating
Temperature
 41 to 95 degrees F (5 to 35
degrees C)

GS-SR113 System Installation Guide
10
4. Contents Package
When opening the package, please ensure the system
components are not damaged during the shipping. Using the
following checklist to verify the contents. If any component is
missing or damaged in the system, please contact your vendor
immediately.
Component Content List
 Chassis
 Power Supply (Installed)
 8IRXR-D Motherboard (Installed)
 Slim type CD-ROM drive (Installed)
 Slim type Floppy drive (Installed)
 Three Hard Disk Drive Trays
 One CPU heat sink pack (including one heat sink, one
thermal conductivity compound, and two cooler bracket)
 Two Dock Handle with two tow screws
 Driver and Application CD
 System Installation Guidebook
 GA-8IRXRR Motherboard manual

GS-SR113 System Installation Guide
11
5. System Installation Procedures
Please remove the protective thin films (Top and bottom)
from the system when installing.
5.1. Chassis Removal
Step 1. Unscrew the two thumbscrews from the back of the
system. (Fig-1)
Figure 1 Figure 2
Step 2. Standing at the front of the system. Gently apply force to
the indentures with your thumbs and push toward the rear of the
chassis for about 3/4 of an inch. Top cover may be lifted straight
up. (Fig-2)
Step 3. After removing the top cover, you will see a plastic airflow
duct over the CPU and Memory. Rise up the airflow duct. (Fig-3)
Step 4. Install CPU and other essential components.

GS-SR113 System Installation Guide
12
Figure 3
5.2. CPU Installation
Step 1. Please make sure the CPU type and speed that are
supported by the motherboard.
Step 2. To Install the CPU, lift up the bar that located next to the
socket. (Fig-4)
Figure 4
Step 3. The noticed corner should point toward the end of lever.
The CPU will only fit in the orientation as shown. (Fig-5)

GS-SR113 System Installation Guide
13
Figure 5
Step 4. Then, align the CPU and insert it into the socket. (Fig-6)
Step 5. Push the lever back to the original position to finish the
CPU installation. (Fig-7)
Figure 6 Figure 7

GS-SR113 System Installation Guide
14
5.3. Heat Sink Installation
Step 1. Put the Heat sink on the CPU.
Figure 8 Figure 9
Step 2. Before putting the heat sink on the CPU, please well
remember to apply the thermal conductivity compound on the
CPU.
Step 3. Seat the heat sink in the retention modules with the four
screws. (Fig-8)
Step 3. Secure the heat sink firmly with two cooler brackets.
There are two dark mark printed on the heat sink. Align the center
of the cooler bracket to the dark mark and push it down (Fig-9).
Step 4. Hook one end of the cooler bracket to the CPU socket as
shown in the Fig-10. Hook the other end of the cooler bracket by
gripping it to another side of retention module.

GS-SR113 System Installation Guide
15
Figure 10
5.4. Memory Installation
The motherboard contains two slanted DIMM (Dual Inline Memory
Module) sockets. The systems BIOS will auto detect the size if the
memory after installing. To install memory, simply push the
memory modules into the DIMM sockets. (Fig 11)
Figure 11

GS-SR113 System Installation Guide
16
5.5. PCI Expansion Card Installation
GS-SR113 provides one expansion riser slot for two peripheral
cards, 32Bit/33 MHz full-height. To install the peripheral, please
go through the following steps.
Step 1. There are two screws holding the riser bracket. First,
remove the screw on the top of the bracket, then, remove another
screw located at the rear of the server. (Fig -12 & 13).
Figure 12 Figure 13
Step 2. Carefully pull up and remove the PCI riser bracket. (Fig-
14).
Figure 14