Gigabyte TO22-Z61 User manual

TO22-Z61
TO22-Z62
AMD EPYC™ DP Compute Nodes
User Manual
Rev. 1.0

Copyright
© 2019 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specications and features in this manual may be made by GIGABYTE without
prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
Documentation Classications
In order to assist in the use of this product, GIGABYTE provides the following types of documentation:
 User Manual: detailed information & steps about the installation, conguration and use of this
product (e.g. motherboard, server barebones), covering hardware and BIOS.

User Guide: detailed information about the installation & use of an add-on hardware or
software component (e.g. BMC rmware, rail-kit) compatible with this product.
Quick Installation Guide: a short guide with visual diagrams that you can reference easily for
installation purposes of this product (e.g. motherboard, server barebones).
Please see the support section of the online product page to check the current availability of these
documents.
For More Information
For related product specications, the latest rmware and software, and other information please visit our website at
http://www.gigabyte.com
For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our reseller
portal: http://reseller.b2b.gigabyte.com
For further technical assistance, please contact your GIGABYTE representative or visit
https://esupport.gigabyte.com/ to create a new support ticket
For any general sales or marketing enquiries, you may also message GIGABYTE server directly by email:
server[email protected]

Conventions
The following conventions are used in this user's guide:
NOTE!
Gives bits and pieces of additional
information related to the current topic.
CAUTION!
Gives precautionary measures to
avoid possible hardware or software problems.
WARNING!
Alerts you to any damage that might
result from doing or not doing specic actions.

Server Warnings and Cautions
Before installing a server, be sure that you understand the following warnings and cautions.
WARNING!
To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against it.
Pay particular attention to the plug, electrical outlet, and the point where the cord extends from
the server.
WARNING!
To reduce the risk of personal injury from hot surfaces, allow the drives and the internal
system components to cool before touching them.
WARNING!
This server is equipped with high speed fans. Keep away from hazardous moving fan
blades during servicing.
CAUTION!
• Do not operate the server for long periods with the access panel open or removed. Operat-
ing the server in this manner results in improper airow and improper cooling that can lead to
thermal damage.
• Danger of explosion if battery is incorrectly replaced.
• Replace only with the same or equivalent type recommended by the manufacturer.
• Dispose of used batteries according to the manufacturer’s instructions.

Electrostatic Discharge (ESD)
CAUTION!
ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU
PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,
PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-
TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER
WHEN HANDLING PARTS.
Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by
their edges without any component and pin touching. After removing a board from its protective
wrapper or from the system, place the board component side up on a grounded, static free sur-
face. Use a conductive foam pad if available but not the board wrapper. Do not slide board over
any surface.
System power on/off: To remove power from system, you must remove the system from rack.
Make sure the system is removed from the rack before opening the chassis, adding, or removing
any non hot-plug components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be present
on power, telephone, and communication cables. Turn off the system and discon-nect the cables
attached to the system before servicing it. Otherwise, personal injury or equipment damage can
result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage drives, boards, and
other parts. We recommend that you perform all procedures in this chapter only at an ESD work-
station. If one is not available, provide some ESD protection by wearing an antistatic wrist strap
attached to chassis ground (any unpainted metal surface on the server) when handling parts.
ESD and handling boards: Always handle boards carefully. They can be extremely sensi-tive to
electrostatic discharge (ESD). Hold boards only by their edges. After removing a board from its
protective wrapper or from the system, place the board component side up on a grounded, static
free surface. Use a conductive foam pad if available but not the board wrapper. Do not slide
board over any surface.
Installing or removing jumpers: A jumper is a small plastic encased conductor that slips over
two jumper pins. Some jumpers have a small tab on top that can be gripped with n-gertips or
with a pair of ne needle nosed pliers. If the jumpers do not have such a tab, take care when us-
ing needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with the

pliers, never the wide sides. Gripping the wide sides can dam-age the contacts inside the jumper,
causing intermittent problems with the function con-trolled by that jumper. Take care to grip with,
but not squeeze, the pliers or other tool used to remove a jumper, or the pins on the board may
bend or break.
CAUTION!
Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery
only with the same or equivalent type recommended by the manufacturer. Dispose of used bat-
teries according to the manufacturer’s instructions.

- 7 -
Table of Contents
Chapter 1 Hardware Installation ................................................................................... 11
1-1 Installation Precautions.................................................................................. 11
1-2 Product Specications.................................................................................... 12
1-3 System Block Diagram................................................................................... 14
Chapter 2 System Appearance.....................................................................................15
2-1 Front View...................................................................................................... 15
2-2 Rear View....................................................................................................... 15
2-3 Front Panel LED and Buttons ........................................................................ 16
2-4 Front System LAN LEDs................................................................................ 17
2-5 Hard Disk Drive LEDs .................................................................................... 18
Chapter 3 System Hardware Installation ......................................................................19
3-1 Installinging Node into The Shelf ................................................................... 20
3-2 Installing the Hard Disk Drive......................................................................... 21
3-2-1 Installing the Hard Disk Drive on the Middle Tray (TO22-Z62 Only).......................22
3-2-2 Removing Hard Disk Drive Middle Tray (TO22-Z62 Only)......................................23
3-2-3 Removing Hard Disk Drive Cage (TO22-Z62 Only)................................................24
3-3 Removing System Cover ............................................................................... 25
3-4 Installing the CPU .......................................................................................... 26
3-5 Removing and Installing the Heatsink............................................................ 27
3-6 Installing Memory........................................................................................... 28
3-6-1 Eight Channel Memory Conguration.....................................................................28
3-6-2 Installing Memory ...................................................................................................28
3-6-3 DIMM Population Table ..........................................................................................29
3-7 Installing the PCI Expansion Card ................................................................. 30
3-8 Replacing and Installing the OCP Card (TO22-Z62 Only) ............................. 32
3-9 Replacing the Fan Assembly.......................................................................... 33
3-10 Cable Routing (TO22-Z61)............................................................................ 34
3-11 Cable Routing (TO22-Z62)............................................................................ 36
Chapter 4 Motherboard Components ...........................................................................39
4-1 Motherboard Components ............................................................................. 39
4-2 Jumper Setting .............................................................................................. 40
Chapter 5 BIOS Setup ..................................................................................................41
5-1 The Main Menu .............................................................................................. 43

- 8 -
5-2 Advanced Menu ............................................................................................. 45
5-2-1 iSCSI Conguration ................................................................................................46
5-2-2 QLogic 577xx/578xx 10 Gb Ethernet BCM57810...................................................47
5-2-3 VLAN Conguration................................................................................................60
5-2-4 CPU Conguration..................................................................................................62
5-2-5 SATA Conguration.................................................................................................64
5-2-6 USB Conguration..................................................................................................65
5-2-7 AST2500 Super IO Conguration...........................................................................67
5-2-8 Serial Port Console Redirection .............................................................................70
5-2-9 PCI Subsystem Settings.........................................................................................75
5-2-10 Network Stack ........................................................................................................77
5-2-11 CSM Conguration .................................................................................................78
5-2-12 Trusted Computing .................................................................................................80
5-2-13 NVMe Conguration ...............................................................................................81
5-3 AMD CBS Menu............................................................................................. 82
5-3-1 Zen Common Options ............................................................................................83
5-3-2 DF Common Options..............................................................................................86
5-3-3 UMC Common Options ..........................................................................................87
5-3-4 NBIO Common Options..........................................................................................94
5-3-5 FCH Common Options ...........................................................................................95
5-4 Chipset Setup Menu....................................................................................... 97
5-4-1 North Bridge ...........................................................................................................98
5-4-2 Error Management................................................................................................101
5-5 Server Management Menu........................................................................... 102
5-5-1 System Event Log ................................................................................................104
5-5-2 View FRU Information ..........................................................................................105
5-5-3 BMC Network Conguration .................................................................................106
5-5-4 IPv6 BMC Network Conguration.........................................................................108
5-6 Security Menu .............................................................................................. 110
5-6-1 Secure Boot.......................................................................................................... 111
5-7 Boot Menu.................................................................................................... 115
5-7-1 UEFI NETWORK Drive BBS Priorities ................................................................117
5-7-2 UEFI Application Boot Priorities ................................................................. 118
5-8 Save & Exit Menu......................................................................................... 119
5-9 ABL POST Codes ........................................................................................ 120
5-9-1 StartProcessorTestPoints .....................................................................................120
5-9-2 Memory test points ...............................................................................................120
5-9-3 PMU Test Points ...................................................................................................120
5-9-4 Original Post Code ...............................................................................................121
5-9-5 CPU test points.....................................................................................................122
5-9-6 Topology test points..............................................................................................122

- 9 -
5-9-7 Extended memory test point.................................................................................122
5-9-8 Gnb Earlier init......................................................................................................123
5-9-9 PMU test points ....................................................................................................126
5-9-10 ABL0 test points ...................................................................................................126
5-9-11 ABL5 test points ...................................................................................................126
5-10 Agesa POST Codes..................................................................................... 130
5-10-1 Universal Post Code.............................................................................................130
5-10-2 [0xA1XX] For CZ only memory Postcodes ...........................................................130
5-10-3 S3 Interface Post Code ........................................................................................133
5-10-4 PMU Post Code....................................................................................................133
5-10-5 [0xA5XX] assigned for AGESA PSP Module ........................................................133
5-10-6 [0xA9XX, 0xAAXX] assigned for AGESA NBIO Module .......................................136
5-10-7 [0xACXX] assigned for AGESA CCX Module .......................................................138
5-10-8 [0xADXX] assigned for AGESA DF Module..........................................................139
5-10-9 [0xAFXX] assigned for AGESA FCH Module........................................................139
5-11 BIOS POST Beep code (AMI standard)....................................................... 141
5-11-1 PEI Beep Codes...................................................................................................141
5-11-2 DXE Beep Codes .................................................................................................141

- 10 -
This page intentionally left blank

- 11 - Hardware Installation
1-1 Installation Precautions
The motherboard/system contain numerous delicate electronic circuits and components which
can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully
read the service guide and follow these procedures:
• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
• When connecting hardware components to the internal connectors on the motherboard,
make sure they are connected tightly and securely.
• When handling the motherboard, avoid touching any metal leads or connectors.
• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist
strap, keep your hands dry and rst touch a metal object to eliminate static electricity.
• Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
• Before unplugging the power supply cable from the motherboard, make sure the power
supply has been turned off.
• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
• Before using the product, please verify that all cables and power connectors of your
hardware components are connected.
• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
• Do not place the computer system on an uneven surface
.
• Do not place the computer system in a high-temperature environment.
• Turning on the computer power during the installation process can lead to damage to
system components as well as physical harm to the user.
• If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certied computer technician.
Chapter 1 Hardware Installation

Hardware Installation - 12 -
1-2 Product Specications
CPU AMD EPYC™ 7001 series processor families
Socket 2 x SP3 Socket
Chipset System on Chip (SoC)
Memory 16 x DIMM slots
DDR4 memory supported only
8-channel memory architecture
8-channel RDIMM/LRDIMM
1.2V modules: 2667/2400/2133 MHz
LAN 2 x 1Gb/s BASE-T LAN ports (Intel® I350-AT2)
1 x Dedicated management port
Expansion Slots
(TO22-Z61)
2 x PCIe x16 (Gen3 x16) slots, Low prole, half length
1 x OCP mezzanine slot (Gen3 x16)
(TO22-Z62) 2 x PCIe x16 (Gen3 x16) slots, Low prole, half length
1 x OCP mezzanine slot (Gen3 x16), occupied by CNVO124, 4 x U.2 HBA
Video Integrated in Aspeed® AST2500
2D Video Graphic Adapter with PCIe bus interface
1920x1200@60Hz 32bpp, DDR4 SDRAM
Storage
(TO22-Z61)
Front side: 2 x 2.5" hybrid NVMe/SATA/SAS + 2 x 2.5" SATA/SAS hot-swap bays
Storage
(TO22-Z62)
Front side: 4 x 2.5" hybrid NVMe/SATA/SAS
Internal: 4 x 2.5" NVMe xed bays
Internal
Connectors
1 x COM header
1 x TPM header
1 x IPMB header
1 x Function jumper
Front Panel
LED/Buttons
1 x Power Button
1 x ID Button
1 x System Status LED
Rear Panel I/O 2 x USB 3.0 ports
1 x 10/100/1000 Server Management LAN port
2 x RJ-45 ports
TPM 1 x TPM header with LPC interface
Optional TPM2.0 kit: CTM000

- 13 - Hardware Installation
System
Management
Aspeed® AST2500 management controller
Avocent® MergePoint IPMI 2.0 web interface:
Network settings
Network security settings
Hardware information
Users control
Services settings
IPMI settings
Sessions control
LDAP settings
Power control
Fan proles
Voltages, fans and temperatures monitoring
System event log
Events management (platform events, trap settings, email settings)
Serial Over LAN
vKVM & vMedia (HTML5)
Form Factor Propriety Form Factor; 6.5" x 19.4",, 12 layers PCB
Power Power Consumption: 480W (Max)
Ambient
Temperature
Relative
Humidity
Operating temperature: 10°C to 35°C
Operating humidity: 8-80% (non-condensing)
Non-operating temperature: -40°C to 60°C
Non-operating humidity: 20%-95% (non-condensing)
System
Dimension
440 x 87 x 820
* We reserves the right to make any changes to the product specications and product-related information without prior
notice.

Hardware Installation - 14 -
1-3 System Block Diagram
TO22-Z61
TO22-Z62
M.2
Intel
i350
NCSI
2A~2D
PCIe3.0
x
16
PCIe3.0
x
8
PCIe3.0
x
16
PCIe3.0 x 2
PCIe3.0
x 1
2 x USB2.0
LPC
RGMII
PCIe3.0
x 4
M.2
PCIe3.0
x
4
2 x USB3.0
PCIe x16 Slot
PCIe x16 Slot
MDI
2 x 1G LAN
TPM
VGA
COM
Switch
ASPEED
AST2500
BMC
MAC
To CMC
Switch MLAN
RTL8211
Rear 2 x USB 3.0
8 Channels
DDR4
8 Channels
DDR4
2666/2400/2133 MHz2666/2400/2133 MHz
PCIe3.0
x
16
PCIe3.0
x
8
2-bay 2.5"
NVMe/SATA HDD
“Zen” Core
Sockets SP3
CPU_1
2-bay 2.5"
SATA/SAS HDD
PCIe3.0
x
16
NCSI
OCP Mezz.
6 x SATAIII SlimLine SAS
10.6GT/s; 11.7GT/s; 12.8GT/s
4x16 GOP
“Zen” Core
Sockets SP3
CPU_0
Board to
Board Conn.
Board to
Board Conn.
M.2
PCIe3.0
x
16
2A~2D
PCIe3.0
x
16
PCIe3.0
x
8
PCIe3.0
x
16
PCIe3.0 x 2
PCIe3.0
x 1
2 x USB2.0
LPC
RGMII
PCIe3.0
x 4
PCIe3.0
x
16
2 x USB3.0
PCIe x16 Slot
PCIe x16 Slot
MDI
2 x 1G LAN
TPM
VGA
COM
Intel
i350
NCSI
NCSI
ASPEED
AST2500
BMC
To CMC
Switch MLAN
RTL8211
MAC
Rear 2 x USB 3.0
8 Channels
DDR4
8 Channels
DDR4
2666/2400/2133 MHz2666/2400/2133 MHz
10.6GT/s; 11.7GT/s; 12.8GT/s
4x16 GOP
6 x SATAIII
SlimLine SAS
Switch
4-bay 2.5"
NVMe/SATA HDD
4-bay 2.5"
NVME HDD
M.2
PCIe3.0
x
4
PCIe3.0
x
8
“Zen” Core
Sockets SP3
CPU_1
OCP Mezz.
“Zen” Core
Sockets SP3
CPU_0
Board to
Board Conn.
Board to
Board Conn.

- 15 - System Appearance
Chapter 2 System Appearance
2-1 Front View
No. Decription
1. ID LED
2. VGA Port
3. 10 GbE LAN Port x 2
4. Server Management LAN Port
5. System Status LED
6. Power Button
7. ID Button
• Please Go to Chapter 2-3 Front Panel LED and Buttons for detail description of
function LEDs.
2-2 Rear View
No. Decription
1. Bus Bar Power Connector
HDD #1
HDD #0
HDD #3
NVMe Compatible
HDD #2
NVMe Compatible
5
6
7
1 3
24
1

System Appearance - 16 -
2-3 Front Panel LED and Buttons
No. Name Color Status Description
1. ID Button
with LED
Blue On System identication is active.
N/A Off System identication is disabled.
2. System
Status LED
Green On System is operating normally.
Amber
On
Critical condition, may indicates:
System fan failure
System temperature
Blink
Non-critical condition, may indicates:
Redundant power module failure
Temperature and voltage issue
Chassis intrusion
N/A Off
Non-critical condition, may indicates:
Redundant power module failure
Temperature and voltage issue
Chassis intrusion
2
1

- 17 - System Appearance
2-4 Front System LAN LEDs
No. Name Color Status Description
1. 1GbE
Speed LED
Yellow On 1Gbps data rate
Green On 100 Mbps data rate
N/A Off 10 Mbps data rate
2.
1GbE
Link/
Activity LED
Green
On Link between system and
network or no access
Blink Data transmission or receiving is occurring
N/A Off No data transmission or receiving is occurring
1 12 2 1 2

System Appearance - 18 -
2-5 Hard Disk Drive LEDs
RAID SKU HDD Fault
Locate HDD
Access
HDD Present
(No Access)
No RAID configuration
(via HBA)
RAID configuration
(via HW RAID Card or
SW RAID Card)
Disk LED
(LED on
Back Panel)
Amber
Removed HDD Slot
(LED on Back Panel)
Disk LED
Removed HDD Slot
Green ON(*1) OFF BLINK (*2)
BLINK (*2)
OFF
OFF
OFF
ON
OFF
ON(*1)
OFF
OFF
ON
OFF
ON
(Low Speed: 2 Hz)
(*3)
(*3)
OFF
OFF
--
--
Green
Amber
Green
ON(*1) OFF --
--
--
--
--
Green
OFF OFF --
Amber
Amber OFF OFF
Rebuilding
OFF
LED1
LED 2 HDD Present No HDD
Green ON OFF
NOTE:
*1: Depends on HBA/Utility Spec.
*2: Blink cycle depends on HDD's activity signal.
*3: If HDD is pulled out during rebuilding, the disk status of this HDD is regarded as faulty.
/('
/('

- 19 - System Hardware Installation
Pre-installation Instructions
Computer components and electronic circuit boards can be damaged by discharges of static
electricity. Working on computers that are still connected to a power supply can be extremely
dangerous. Follow the simple guidelines below to avoid damage to your computer or injury to
yourself.
• Always disconnect the computer from the power outlet whenever you are working inside
the computer case.
• If possible, wear a grounded wrist strap when you are working inside the computer case.
Alternatively, discharge any static electricity by touching the bare metal system of the
computer case, or the bare metal body of any other grounded appliance.
• Hold electronic circuit boards by the edges only. Do not touch the components on the
board unless it is necessary to do so. Do not ex or stress the circuit board.
• Leave all components inside the static-proof packaging until you are ready to use the
component for the installation.
Chapter 3 System Hardware Installation

System Hardware Installation - 20 -
3-1 Installinging Node into The Shelf
Before you install the node into the rack:
• Make sure the system is not turned on or connected to AC power.
Follow these instructions to install a node into the shelf:
1. Installthenodeintotheshelfandmakesureitseatedrmly.