Gigaset C610-C610A, QUG, Grossbritannien, A31008-M2325-L101-1-7643
GIGASET HELPLINE: 0845 3670812
Quick Start Guide
Pack contents
If you have purchased a model
with multiple handsets the
package should contain two bat-
teries, a battery cover, a belt clip
and a charging cradle 9with
mains adapter Jfor each addi-
tional handset.
21
345
7
6
8
1one Gigaset C610A base
2one mains adapter
3one Gigaset C610H handset
4one phone cord
5two batteries
6one battery cover
7one belt clip
8one user guide
plus one quick start guide
Connecting the base station
¤First connect
the mains
adapter 1.
¤Then connect
the telephone
jack 2and
insert the
cables into the
cable ducts.
Please note:
uThe mains
adapter must always be connected, as the phone will not operate without a
mains connection.
uOnly use the mains adapter and phone cord supplied. Pin connections on tele-
phone cables can vary.
uThe LED display should light up at the base station. If not, please
ensure the power lead is fully inserted.
Connecting the charging cradle (if included)
¤Plug the mains adapter into the plug
socket 2.
¤Connect the flat plug from the mains
adapter 1.
If you need to disconnect the plug from the charg-
ing cradle, press the release button 3and discon-
nect the plug 4.
1
2
4
3
Final check list
To ensure your product is set up correctly please check the
following
uHave you used phone cord supplied
uHave you fully inserted the power cable into base station
uHave you inserted batteries correctly
uHave you charged the batteries for 10 hours
uHave you set up Date/Time
PLEASE NOTE:
For a dial tone press the call button cfor approx. 2 seconds. Short press opens
redial list.
Message Indication Key fon handset will flash to indicate one or all of the following
events:
umissed calls (if caller ID is enabled for your line numbers will be shown)
unew messages on the answering machine (also indicated by flashing message
counter on base station)
unew Text messages (SMS) received
If you have problems setting up or operation this product please call
GIGASET HELPLINE
0845 3670812
Issued by
Gigaset Communications GmbH
Frankenstr. 2a. D-46395 Bocholt
© Gigaset Communications GmbH 2011
All rights reserved. Subject to availability.
Rights of modification reserved.
www.gigaset.com
A31008-M2325-L101-1-7643
Preparing the handset
Initial charging and discharging of the batteries
The correct charge level can only be displayed if the batteries are first fully charged
and discharged.
¤Insert the batteries the right
way round.
The polarity is indicated in/on
the battery compartment.
¤First insert the battery cover at
the top a.
¤Then press the cover buntil it
clicks into place.
If you need to open the battery cover, for
instance to replace the batteries, place
your fingertip in the cavity on the casing
and pull the battery cover upwards.
a
b
¤Place the handset in the base/charging cradle for
10 hours.
¤Then remove the handset
from the base/charging cradle
and do not replace it until the
batteries are fully discharged.
10 h
Setting the date and time
Set the date and time so that the correct date and time can be assigned to incoming
calls, and so that the alarm can be used.
Date/Time
Date:
14.10.2009
Time:
00:00
Date/Time
Date:
31.01.2011
Time:
00:00
¤Press the key below §Time§ on the
screen display to open the input
field.
The Date/Time submenu is shown on
the display.
¤The active input position flashes.
Enter day, month and year as an
8-digit number via the keypad,
e.g. 4Q
2Q
for 14/10/2011.
Press the right or left control key to
change the input position and cor-
rect an entry.
¤Enter the hours and minutes as
four digit numbers via the keypad,
e.g. QM5for 07:15 am.
Change the input position with
the control key if necessary.
¤Press down on the control key to switch to the
time input field.
Setting the date and time
Display in idle status
uReception signal between the base and handset:
– good to poor: ÐiÑÒ
–noreception:|flashes
Green: Eco Mode activated
uÃ: answering machine is activated
uBattery charge status:
–yy{{(empty to full)
–yflashes red: batteries almost empty
–xyx{x{(charging)
uINT 1: Internal name of the handset
If Eco Mode+ is activated, the ¼icon is displayed in
the top left (see chapter “ECO DECT” of user manual.
¤Press the key below §Save§ on the display
screen to confirm your entry.
The display shows Saved. You will hear a con-
firmation tone and the handset will automat-
ically return to idle status.
i à ¤V
07:15
INT 1 14 Oct
Calls SMS
Frequently asked questions
Q: There is no dial tone.
A: Press call button for 2 seconds (long press) to obtain dial tone. A short press opens
the redial list.
Q: The line is crackling / not clear.
A: Have you used the new line cable provided? Please do not use an old cable.
Q: Message indicator flashing on handset and I cannot retrieve my message.
A: Message indicator will flash to indicate missed call as well as new message or text
message.
Please check it is not indicating a new missed call or text message.
Q: The caller ID is not functioning.
A: Have you subscribed to this service (CLIP) from your provider?
Q: Can I record my own announcement on the answer machine.
A: Yes. Please refer to Chapter
“Operating the answer machine of the Gigaset C610A base station”
of your user manual (p. 47).
Q: The display is not clear.
A: The display is protected by a plastic film, please make sure you have removed the
protective film.
Q: The handset is not registered.
A: If your handset is not registered, please refer to Chapter “Registering handsets”
of your user manual (p. 55) to instructions how to register handsets manually.
For more QUESTIONS AND ANSWERS please refer to chapter “Service (Customer
Care)” of user manual (p. 69).
