Gilbert & Bennett SH101 User manual

Page 1 of 307/28/21 Customer Service: 847-821-9646
ROUND HAND-
HAMMERED 100%
COPPER FIRE TUB
SH101 USER MANUAL
DO NOT allow small children near ame. Hot
embers can y out of the re tub in windy
conditions. Adequate re extinguishing material
should be readily available.
Some parts may contain sharp edges. Wear
protective gloves as necessary.
Always use mesh spark guard when re is lit.
The re bowl is hot! Do not touch or allow children
near re bowl while it is in use.
Keep a re extinguisher, garden hose, or bucket of
sand nearby to smother re if necessary.
Spark guard handle will be hot when in use. To
remove, use a heat-proof barbeque mitt or poker
tool to grasp handle.
Your re bowl is made of metal. There may be
roughness on the surface and design. This “one of a
kind” look enhances the beauty of the product and
is not a defect.
Finish will not look the same after burning.
Add at least 1 inch of sand to the bottom of the re
tub. This will distribute the heat more evenly.
CARBON MONOXIDE HAZARD - Burning charcoal
inside can kill you. It gives off carbon monoxide,
which has no odor. NEVER burn wood or charcoal
inside homes, vehicles, or tents.
DO NOT use this unit on a wood deck or other
combustible surfaces such as dry grass, leaves,
mulch, etc. DO NOT use this near heat sensitive
or combustible structures such as vinyl or wood
siding.
WARNING: Combustion by-products produced
when using this product include carbon monoxide
and other chemicals known to the State of
California to cause cancer and birth defects or
other reproductive harm.
CAUTION
NOTES
CAUTION
IMPORTANT SAFETY INSTRUCTIONS
Please read and follow all Safety Statements, Warnings, Notes and Assembly Instructions before
attempting to assemble and use this unit.
FOR OUTDOOR USE ONLY!
Approved items for burning are wood, self-starting
re logs and charcoal.
DO NOT put vinyl cover on until re bowl is
completely cooled and embers are extinguished.

Page 2 of 307/28/21 Customer Service: 847-821-9646
Parts Description Quantity
ASpark Guard 1
B Copper Fire Bowl 1
Parts Description Quantity
CStand with Legs 1
DVinyl Cover 1
Assembly
Please check enclosed parts shipped with this product. If any parts are missing, do not return the item to the retailer.
Please contact us for replacement parts by calling Customer Service at 847-821-9646.
1. Hold COPPER FIRE BOWL (B) above the
STAND (C) and gently lower into place.
2. Place SPARK GUARD (A) onto COPPER FIRE
BOWL (B).
A
B
D
C

Page 3 of 307/28/21 Customer Service: 847-821-9646
Copyright © 2021
Midwest Air Technologies, Inc.
6700 Wildlife Way
Long Grove, IL 60061
Thank you for your purchase of a quality Gilbert & Bennett™ Fire Pit. With proper care and maintenance your
Gilbert & Bennett™ product will provide you with years of entertainment.
Your re pit is made of metal, and will be susceptible to rust and other changes due to exposure from
smoke, heat and weather.
Helpful Tips for Proper Maintenance
• Remove ash when the product has cooled down after each and every use.
• Cover your product with vinyl weather cover when product is cool and not in use.
• Place at least an inch of sand in the base of the pit to help distribute heat evenly.
• Do not overll your pit with fuel when in use.
Color change to the metal on the outside of your pit is normal, and should be expected. The color change
occurs due to the effects of weather, heat, and smoke. To limit this color change, burn clean high-quality
wood and keep your re pit covered when not in use. You can also clean your product after each with soap,
water, and the metal-appropriate polish and touch paint up with a high-temperature paint if so desired.
If you have any questions, concerns, or comments about your Gilbert & Bennett™ product, you can contact
us at [email protected], or by calling us at 847-821-9646.