Gill 7040 User manual

PART # DESCRIPTION QTY.
1 M476 1.5" Sq End Plug, Black (14-20 gage) 2
2 M477 1.5" x 3" End Plug, Black, (10-14 ga) 1
3 M2015 Felt Dot, 1" dia x 1/8" thick, adhesive backed 12
4 M2861 Knob 3/8"-16 x 1", Nylon tip, black TPE, Logo 1
5 M2207 5/16"-18 x 1.5" Hex Bolt 4
6 M2273 Washer, Flat, 5/16 12
7 M1254 5/16"-18 Nylock Hex Nut 8
2008 by Gill Athletics. All rights reserved.
GILL ATH
7040 - SCHOLASTIC HIGH JUMP STANDARDS
7040_inst1
www.gillathletics.com
10/26/2012
ASSEMBLY INSTRUCTIONS
Copyright 
800-637-3090
Upright
2
(2) 1/2" Wrenches
(1) Flat head screwdriver
Tools required:
First attach the wheels and the rubber feet to the base (see page 2).
Second fasten the upright to the base as shown below.
To adjust the height of the riser, loosen the knob (1), position the
riser at the desired height, and re-tighten the knob. Read the height
scale at the top of the lower riser guide as indicated by the white
pointer decal. The scale on one side of the upright is for the lower
bar rest and the scale on the other side is for the higher bar rest.
The scale reads in both feet & inches and metric (centimeters).
Caution: Over-tightening the knob can result in damaged threads,
which may cause the knob to seize in place and may require a new
knob and/or riser.
Base
4
1
3
Riser
Base
5
6
6
7
Upright/Riser

THIS WARNING IS GIVEN IN COMPLIANCE
WITH CALIFORNIA'S PROPOSITION 65:
WARNING
This product contains chemicals known to the
State of California to cause cancer, birth defects
or other reproductive harm.
touches the wheel. The wheel should spin freely.
the nylon insert is fully engaged, but not to the point where the nut
holding the wheel on the axle. The nut should be tightened so that
in place with a second nylock nut. Do not over tighten the nut
wheel (4) with installed bearings (5) onto the axle bolt and secure it
with a nylock nut (8). This nut must be fully tightened. Slide the
washers (6) and the hole in the side of the base. Secure it in place
To assemble the wheels, first feed the axle bolt (7) through the
(2) and nut (3)
Fasten the rubber feet (1) to the bottom of the base with a screw
Part # Description Qty
1 M726 Black Rubber Foot 4
2 M2229 6-32 x 5/8" Screw, Slotted Truss Head 4
3 M2228 6-32 Flange Whiz-Nut 4
4 M718 61 mm skate wheel 2
5 M717B Ball Bearing 4
6 M2273 Washer, Flat, 5/16 4
7 M2834 5/16"-18 x 2" Hex Bolt Full Thread 2
8 M1254 5/16"-18 Nylock Hex Nut 4
2008 by Gill Athletics. All rights reserved.
GILL ATH
7040 - SCHOLASTIC HIGH JUMP STANDARDS
7040_inst2
www.gillathletics.com
10/26/2012
ASSEMBLY INSTRUCTIONS
Copyright 
800-637-3090
1
7
6
6
8
4
5
8
5
2
3

P704030
• Minus clamping knob
M2861
P7040R
Knob with nylon tip
P704040L
Upright & Riser
Left side
P704040R
Upright & Riser
Right side
P7040L
Complete Standard
Complete Standard
Right side only
Left side only
Single Riser with knob
Hardware for a single standard
700160
P704005
Single Base with
wheels and hardware
GILL ATH
2008 by Gill Athletics. All rights reserved.
www.gillathletics.com
REPLACEMENT PARTS
7040_inst3
7040 - SCHOLASTIC HIGH JUMP STANDARDS
10/26/2012
Copyright 
800-637-3090