Gill 7100 User manual

7/19/2020
www.gillathletics.com
7100 - ESSENTIALS POLE VAULT STANDARD
INST7100
800-637-3090
All rights reserved. Page 1 of 6
Copyright 2012 by Gill Athletics.
ASSEMBLY INSTRUCTIONS
Specifications:
The upright and riser are made of steel tubing. The
bases, uprights and risers are powder coated black.
The offsets are powder coated white. Height adjustment
from 6' to 16' reading English and Metric. Upright
detaches from base rails for storage. Wide stance base
for added stability. 8 base anchors included. Meets
High School and NCAA specifications.
The base measures 21" x 48" and allows the standard
to adjust from 0"-32" behind the 'zero' line.
Operation:
To adjust the height of the riser, loosen the clamping
knob, position the riser at the desired height, and
re-tighten the knob.
Caution: Over-tightening the knob can result in
damaged threads, which may cause the knob to seize
in place and may require a new knob and/or riser.
Tools you will need:
17mm wrench
13mm wrench
Crescent wrench

www.gillathletics.com
Copyright 2012 by Gill Athletics.
All rights reserved.
800-637-3090
7/19/2020
INST7100
Page 2 of 6
7100 - ESSENTIALS POLE VAULT STANDARD
ASSEMBLY INSTRUCTIONS
Step 2
Assemble the offset and bolt it to the riser.
Make sure that the bar rest pins point
towards the landing pit
Step 1
Attach the bar rest pins to the 63" long, 1"
Sqr. tube of the offset.
Detail A
Detail B
M10 Flat Washer
M10 x 35
Hex Bolt
M10 Lockwasher
Detail C
M10 Nyloc Hex Nut
M10 Flat Washer
M10 x 55
Hex Bolt
B
C
A
75mm Bar Rest Pin
M10 Nyloc Hex Nut
M10 Flat Washer

Detail D
M8 x 25 Hex Bolt
M8 Flat Washer
M8 Nyloc Hex Nut
Upright
Slide Base
Detail E
Step 4
Attach the bolts into the side channels at
the open end of the base as shown below.
M10 x 40 Hex Bolt
M10 Flat Washer
M10 Flat Washer
M10 Nyloc Hex Nut
Step 3
Bolt the upright to the slide base using four
M8x25 hex bolts, four M8 flat washers, and
four M8 Nyloc hex nuts.
www.gillathletics.com
Copyright 2012 by Gill Athletics.
All rights reserved.
800-637-3090
7/19/2020
INST7100
Page 3 of 6
7100 - ESSENTIALS POLE VAULT STANDARD
ASSEMBLY INSTRUCTIONS
D
E

P71002 - Replacement Uprights & Risers
www.gillathletics.com
Copyright 2012 by Gill Athletics.
All rights reserved.
800-637-3090
7/19/2020
INST7100
Page 4 of 6
7100 - ESSENTIALS POLE VAULT STANDARD
ASSEMBLY INSTRUCTIONS
P71001 - Replacement Offsets with Hardware
P71003 - Replacement Base with Hardware
P71429
75mm Bar Rest Pin with Nut
M2861
Clamping Knob

www.gillathletics.com
Copyright 2011 by Gill Athletics.
All rights reserved.
800-637-3090
7/19/2020
INST7100
Page 5 of 6
7100 - ESSENTIALS POLE VAULT STANDARD
ASSEMBLY INSTRUCTIONS
P71004
Replacement Cap Set
(For one Standard)
P71005
Replacement Wheel Kit
(Includes 2 wheels, axle, and hardware)
Part QTY.
M10 x 35 Hex Bolt 4
M10 Lockwasher 4
M10 Flat Washer 16
M10 x 55 Hex Bolt 4
M10 Nyloc Hex Nut 6
M10 x 40 Hex Bolt 2
M8 x 25 Hex Bolt 4
M8 Flat Washer 4
M8 Nyloc Hex Nut 4
P71006
Replacement Hardware
(For One Standard)

THIS WARNING IS GIVEN IN COMPLIANCE
WITH CALIFORNIA’S PROPOSITION 65:
WARNING
This product contains chemicals known to the
State of California to cause cancer, birth defects
or other reproductive harm.
www.gillathletics.com
7100 - ESSENTIALS POLE VAULT STANDARD
ASSEMBLY INSTRUCTIONS
800-637-3090
Copyright 2012 by Gill Athletics.
All rights reserved. Page 6 of 6
INST7100
7/19/2020
Tools Required:
(1) Drill
(1) 7/8" Masonry Bit
(1) Hammer
(1) 3/4" Wrench or Socket
Instructional information from www.mktfastening.com.
PitRunway
Open end
of standard.
Pins face the pit.
Open end
of standard.
Proper alignment of standards is critical before 1.
drilling anchor holes. See the last page for more
information.
After standards have been properly positioned, 2.
mark the hole placement.
Drill recommended diameter hole to depth of shield.3.
Clean hole of debris.4.
Insert shield in hole threaded end first and tap with 5.
hammer for proper positioning.
Place base rail back over holes.6.
Insert included 1/2"-13 bolt and 1/2" washer 7.
through rails into shield and tighten.