Gill 740134 User manual

pull pin and clamping knobs.
beam is locked in position with a stainless steel spring loaded
sleeves set into the wall of a water jump pit. The beam is 12 feet wide
The 740134 Water Jump Barrier is designed to be using ground
The barrier adjusts to three heights; 30, 33, and 36 inches. The
The beam is constructed of 4 inch square 11 gauge steel tube, covered on
three sides with 1/2 inch thick Vultrak track surface.
The leg assemblies are fabricated from 2-1/2 " and 3-1/2" Sch 40 steel pipe
with spring assist. The legs are painted with powder coat for a durable finish.
The leg assemblies are installed into PVC ground sleeves 32 inches deep.
NCAA compliant and IAAF certified.
740134 - WATER JUMP BARRIER - GROUND SLEEVED
www.gillathletics.com
Page 1 of 4
INST740134
6/12/2015
All rights reserved.
800-637-3090
Copyright 2012 by Gill Athletics.
INSTRUCTIONS
Ground Sleeve
knobs for height adjustments
Spring loaded pull pin & clamping
Ground Sleeve
117"
12feet (74014412)

The ground sleeves must be installed at the same time as the front wall of the water jump pit. The
ground sleeves will be cast into the concrete of the front wall of the water jump pit.
It is critical that the ground sleeves be located correctly and held plumb during the entire concrete
pour. The bolts in the bottom of the ground sleeves must be oriented so that they are parallel with
the front wall.
The ground sleeves must be set so that the top of the ground sleeves are level with the finished
elevation of the running track.
Some provision to drain the ground sleeves is recommended.
Make sure that no concrete enters the ground sleeve during the pour.
740134 - WATER JUMP BARRIER - GROUND SLEEVED
www.gillathletics.com
Page 2 of 4
INST740134
6/12/2015
All rights reserved.
800-637-3090
Copyright 2012 by Gill Athletics.
INSTRUCTIONS
4"
32"
A
A
SECTION A-A
117"
BB
Front Wall
SECTION B-B
Bolt at the bottom of
the ground sleeve

State of California to cause cancer, birth defects
THIS WARNING IS GIVEN IN COMPLIANCE
WITH CALIFORNIA'S PROPOSITION 65:
or other reproductive harm.
WARNING
This product contains chemicals known to the
Bolt the upper legs to the bottom of the beam in
four places per leg.
Slide the lower legs into the ground sleeves.
Slide the spring into the top of the lower leg.
Make sure the clamping knobs are backed out.
With at least two people, lift the beam and slide
the upper legs onto the lower legs.
Pull the pin out to adjust to the designed height.
Tighten the clamping knobs to secure the beam.
O-Ring
(MISC00267)
(74013435)
Ground Sleeve
Steeple Chase Upper Leg
(74014020)
(74013430)
Steeple Chase Lower Leg
Place two o-rings on the lower on
ground sleeve and one at the bottom.
each lower leg. One at the top of the
(74014025)
Spring
5/16" Flat Washer
(HDWE050020E0)
3/8"-16 x 1" Hex Bolt
(HDWE011240E0)
2"
31"
All rights reserved.
www.gillathletics.com
Copyright 2012 by Gill Athletics.
All rights reserved.
800-637-3090
6/12/2015
INST740134
Page 3 of 4
740134 - WATER JUMP BARRIER - GROUND SLEEVED
INSTRUCTIONS
Copyright 2012 by Gill Athletics. [email protected]

REPL741401
Press the bushing (BUSH00088) into the pull pin collar so1. that it is flush with the inside wall of the pipe.
Slide the spring (SPNG00041) onto the shaft of the pull pin2. stud (7401402004). Then slide the pull pin collar cap
(7401402003) onto the pull pin stud. Next screw the knob
(HAND00088) onto the pull pin stud and Loc-Tite the
threads.
Screw the pull pin collar cap into the pin collar. Make sure3. to Loc-Tite the threads.
ITEM NO. PART NUMBER Description
1 7401402003 Pull Pin Collar
Cap
2 7401402004 Pull Pin Stud
3 HAND00088 Ball Knob
4 BUSH00088 Shaft Bushing
5 SPNG00041 Spring
ITEM NO. PART NUMBER Description
1 7401402003 Pull Pin Collar
Cap
2 7401402004 Pull Pin Stud
3 HAND00088 Ball Knob
4 BUSH00088 Shaft Bushing
5 SPNG00041 Spring
740134 - WATER JUMP BARRIER - GROUND SLEEVED
www.gillathletics.com
Page 4 of 4
INST740134
6/12/2015
All rights reserved.
800-637-3090
Copyright 2011 by Gill Athletics.
INSTRUCTIONS
2
31
5
4