Gira 1010 00 User manual

GIRA
Info
Weather station
Installation Instructions
Weather station 9/06 Page 1 of 4
System information
This device is a product of the Instabus-KNX/EIB sys-
tem and complies with KNX directives.
Detailed technical knowledge obtained in Instabus
training courses is a prerequisite to proper under-
standing.
The functionality of this device depends upon the soft-
ware.
Detailed information on loadable software and attain-
able functionality as well as the software itself can be
obtained from the manufacturer’s product database.
Planning, installation and commissioning of the unit is
effected by means of KNX-certified software.
An updated version of the product database and the
technical descriptions are available in the Internet at
www.gira.de.
Function
• The weather station serves to collect and to trans-
mit weather data and events. Up to four analog
transducers as well as a digital combination sensor
(order no. 1025 00, measuring wind intensity,
brightness and rain; with DCF77 receiver) can be
connected.
• The weather station evaluates both voltage and
current signals:
Voltage signals: 0 ... 1 V DC 0 ... 10 V DC
Current signals: 0 ... 20 mA DC 4 ... 20 mA DC
• The current inputs 4 ... 20 mA can be monitored for
wire breakage (parameter setting).
Weather station Order no.: 1010 00
Safety instructions
Attention:
• Electrical equipment must be installed and fit-
ted by qualified electricians only and in strict
observance of the relevant accident preven-
tion regulations.
• Failure to observe any of the installation in-
structions may result in fire and other hazards.
•U
Sand GND must not be interconnected with
the corresponding terminals of another device
(risk of irreparable damage).
• The terminal block for the connection of the
combination sensor must be plugged on be-
fore the mains voltage is switched on and dur-
ing operation to prevent the digital input from
unintentional contact with live wires. This
would endanger the safety of the entire sys-
tem.
As a result, the device and any connected sen-
sors may be irreparably damaged.

GIRA
Info
Weather station
Installation Instructions
Weather station 9/06 Page 2 of 4
Installation
Snap the device onto a 35 x 7.5 top hat rail as per EN
50022.
For operation, the 4-channel analog input needs an
external 24 V power source, e.g order no. 1024 00.
This source can additionally supply the connected
sensors as e.g. WS 10W, WS 10R, the combination
sensor or their heatings.
Prior to switching on the voltage, plug on the terminal
block for the connection of a combination sensor,
even if no such sensor is used.
Connection
+Us: power supply of external transducers
GND: ref. potential for +Usand inputs
K1...K4
K1 ... K4: measured-value inputs
EIB: EIB connecting terminal
24 V AC: external power supply voltage
(A): programming key
(B): programming LED
(C): status LED, three-colour
(red, orange, green)
(D): transducer
(E): system connector, 6-pole,
for future extensions
(F): connecting terminal, 4-pole,
for combination sensor
(wind, rain, brightness, twilight)
Wiring diagram
Safety warnings
The terminal block for the connection of the com-
bination sensor must be plugged on before the
mains voltage is switched on and during opera-
tion to prevent the digital input from unintention-
al contact with live wires. This would endanger
the safety of the entire system.
As a result, the device and any connected sen-
sors may be irreparably damaged.

GIRA
Info
Weather station
Installation Instructions
Weather station 9/06 Page 3 of 4
Power supply of sensors connected
• The connected sensors can be supplied from ter-
minals +Usand GND (see fig. c). These terminals
are provided in duplicate and internally intercon-
nected.
• The total current consumption of all sensors sup-
plied this way must not exceed 100 mA.
• In the event of overload or short-circuit between
+Usand GND, the power will be switched off. After
removal of the fault, the power is switched on again
automatically.
• Sensors connected can also be supplied externally
(e.g. if their current consumption exceeds 100 mA).
In such case, they must be connected between ter-
minals K1... K4 and GND.
Attention:
Usand GND must not be interconnected with the
corresponding terminals of another device (risk
of irreparable damage.
Sensors suitable for connection
For any of the following transducers, the software pro-
vides preset values.
If other sensors are used, the parameters to be set
must be determined beforehand.
Commisioning
After switching on the device for the first time, the
weather station starts a module scan (status LED:
‘Orange / on’).
As a new device comes by default without configura-
tion, the status LED shows then ‘Red / quickly blink-
ing’.
After connection, a combination sensor is ready for
operation (as programmed in the weather station).
After downloading a project configuration into the
weather station, the status LED shows ‘Green / on’.
Status LED
OFF: no power supply
Orange/ON: weather station scanning
Red/slowly blinking: error: undervoltage at combi-
nation sensor connec-
tion / short-circuit Us
Red/quickly blinking: error: no project configuration/
false parameters
Green/slowly blinking: address assignment, scan
completed, configuration OK
Green/quickly blinking: parameter download into
combination sensor
Green/ON: scan completed,
everything OK
Slowly blinking = 1/s; quickly blinking = 2/s
Type Use Model Order
No.
Wind, brightness,
Twilight, rain
outdoor Combination
sensor
1025 00
Brightness outdoor WS 10H 0576 00
Twilight outdoor WS 10D 0572 00
Temperature outdoor WS 10T 0577 00
Wind outdoor WS 10W 0580 00
Rain outdoor WS 10R 0579 00

GIRA
Info
Weather station
Installation Instructions
Weather station 9/06 Page 4 of 4
Technical Data
Power supply
Supply voltage: AC 24 V ± 10 %
Current consumption: 250 mA max.
KNX/EIB voltage: 21 - 32 V DC
KNX/EIB power consumption:150 mW typ.
Ambient temperature: -5 °C ... +45 °C
Storage/transport temp.: -25 °C ... +70 °C
Humidity
Ambient/storage/transport: 93 % r.h. max.,
no condensation
Protective system: IP 20 as per
EN 60529
Installation width: 4 modules / 72 mm
Weight: approx. 150 g
Connections
Inputs, power supply: screw terminals
single-wire: 0.5 mm2to 4 mm2
stranded wire
(without ferrule): 0.34 mm2to 4 mm2
stranded wire
(with ferrule): 0.14 mm2to 2.5 mm2
KNX/EIB: connecting and branch
terminal
Combination sensor: 4-pole connecting terminal
Sensor inputs
Number: 4 x analog, 1x digital
Evaluable sensor
signals (analog): 0 … 1 V DC, 0 … 10 V DC,
0 … 20 mA, 4 … 20 mA
Voltage measurement
impedance: approx. 18 k
Current measurement
impedance: approx. 100
External sensor power
supply (+Us): 24 VDC, 100 mA max.
Acceptance of guarantee
We accept the guarantee in accordance with the corresponding legal provisions.
Please return the unit postage paid to our central service department giving a brief description of the
fault:
Gira
Giersiepen GmbH & Co. KG
Service Center
Dahlienstrasse 12
D-42477 Radevormwald
Gira
Giersiepen GmbH & Co. KG
Postfach 1220
D-42461 Radevormwald
Telefon: +49 / 21 95 / 602 - 0
Telefax: +49 / 21 95 / 602 - 339
Internet: www.gira.de