Glab AUX BANK UP/DOWN WITH MIDI IN FOOTSWITCH User manual

AUX BANK UP/DOWN
WITH MIDI IN FOOTSWITCH
Instrukcja obsługi
User Manual
Bedienungsanleitung

1
Dear Customer!
Thank you for choosing our product.
G LAB AUX BANK UP/DOWN with MIDI IN FOOTSWITCH is an expansion module for
GSC-3 and GSC-2 controllers with two footswitches to switch the banks which enable
working with ten presets in the bank and a MIDI IN input enabling to control the GSC by
other device sending the Program Change MIDI commands.
Version 1.1

2
Structure
1 - BANK DOWN footswitch
2 - BANK UP footswitch
3 - MIDI IN channel setting switch

3
4 - MIDI IN connector
5 - MIDI THRU connector
6 - Cable with AUX connector to connect GSC controllers
Connecting the controller
Before connecting the GSC-2 controller check if it posses firmware version 2.20 or
higher. If it doesn’t it is needed to upgrade controller program by using G2SOFT.

4
Before connecting the expansion module it is needed to set AF2 (AUX input function
No. 2) at LOOP button settings (footswitch No. 8) and to choose cb2 or cb3 change bank
mode (by using BANK UP/BANK DOWN footswitches). The module should be
connected to the AUX connector. The cable is 350 mm long and its surplus should be
put inside the module.
Controlling via MIDI
Connect cable with MIDI signal to the MIDI IN input and set MIDI channel to
receive the commands by using MIDI CHANNEL switch. The arrow-head indicates
set channel (A, B, C, D, E, F letters correspond with 10, 11, 12, 13, 14, 15
channels numbers and “0” digit indicates channel No. 16).
The module receives program Change commends in the range from 1 to 100
(program No. 100 corresponds with preset No. P00). It posses MIDI THRU output with
copy of MIDI IN signal.

5
Technical parameters
Dimensions: depth 115 mm
width 90 mm
heigh 62 mm
Weight 350 g
Power supply 12V from AUX output

6
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer for help.

7
Declaration of Conformity
ELZAB S.A., ul. Kruczkowskiego 39, 41-813 Zabrze, Poland,
declare under sole responsibility, that the following product:
G LAB AUX BANK UP/DOWN WITH MIDI IN FOOTSWITCH
conforms with requirements of the EC Council Directives:
●2006/95/EEC Low Voltage Directive,
●2004/108/EEC Electromagnetic Compatibility,
and holds CE mark. Above named product conforms with the following standards:
●PN-EN 60065:2004 /EN 60065:2002/ Audio, video and similar apparatus -
Safety requirements.
●PN-EN 55103-1:2000 /EN 55103-1:1996/ Electromagnetic compatibility -
Product family standard for audio, video, audio-visual and entertainment
lighting control apparatus for professional use - Part 1: Emission
●PN-EN 55103-2:2001 /EN 55103-2:1996/ Electromagnetic compatibility -
Product family standard for audio, video, audio-visual and entertainment
lighting control apparatus for professional use - Part 2: Immunity
Jerzy Biernat
President of the ELZAB S.A. Board of Directors
Copy of original EC declaration of conformity is available for download on our
webside http://www.glab.com.pl

8
DO NOT PLACE THIS PRODUCT INTO THE WASTE CONTAINER !
This device is marked with a cross-lined waste container symbol
according to 2002/96/EU Directive on Waste Electric and Elec-
tronic Equipment.
Such marking informs that after usage equipment can not be
trashed together with other household waste.
An user obligation is to return wasted equipment to a party collecting wasted
electric and electronic equipment. Parties collecting such equipment organise
a system, including local collection points, shops and other units, allowing to
return such equipment. This Directive assures an user free of charge utilisation of
such delivered equipment.
This device is made of materials which can be recycled or utilised after becoming
out of use. Proper handling of wasted electric and electronic equipment reduce
demand for row materials and contribute in avoiding harmful consequences for
environment and health of people caused by dangerous components and not
proper storing and utilising of such equipment.
User Manual, Drawing No. G54INA00

Drawing No. G04INA00
COMPANY ADDRESS
ELZAB SA
ul. Kruczkowskiego 39, 41-813 Zabrze, Poland
phone: [phone], fax: [phone]
Sales & Export Department ......................................
phone: [phone] ext. 34, 39, 64
[phone] ext. 308, 366, 468
e-mail: [e-mail]
Technical Support .....................................................
phone: [phone] ext. 64
[phone] ext. 308
e-mail: [e-mail]
www.glab.com.pl
G LAB is a brand of ELZAB SA