Glacier bay 67536-0508D2 Assembly instructions

THANK YOU
INSTALLATION AND CARE GUIDE
We appreciate the trust and condence you have placed in Glacier Bay through the purchase of this kitchen
faucet. We strive to continually create quality products designed to enhance your home. Visit us online to see
our full line of products available for your home improvement needs. Thank you for choosing Glacier Bay!
PULL-DOWN KITCHEN FAUCET
Questions, problems, missing parts?
Before returning to the store, call Glacier Bay Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday
9 a.m. - 6 p.m., EST, Saturday
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM/GLACIERBAY
THD 07/2015 REV.01
Model# SKU#
67536-0508D2 1001-407-752

2
Table of Contents
Important Information..............................2
Warranty ...................................................2
Pre-Installation.........................................2
Planning Installation ..............................2
Package Contents..................................3
Installation................................................4
Operation ..................................................13
Troubleshooting ......................................15
Care and Cleaning ................................... 14
Service Parts
........................................... 17
Adjustable
wrench
Safety
goggles
Phillips
screwdriver
SILICONE
Silicone
sealant
6mm
diameter
Electric
drill
Tools and Hardware Required ...............2
Important Information
□ Observe all local plumbing and building codes.
□ Cover the sink drain to avoid losing any parts.
□ Review the care and cleaning section included in this guide.
Warranty
LIMITED LIFETIME WARRANTY
Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our
limited lifetime warranty. Glacier Bay products are warranted to the original consumer purchaser to be free of
defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that proves defective.
Sensor mechanism and LED light excluded from Limited Lifetime Warranty and are covered by a 3-year warranty
from date of purchase. Simply, return the product / part to any of The Home Depot retail locations or call 1-855-HD-
GLACIER (1-855-434-5224) to receive the replacement item. Proof of purchase (original sales receipt) from the
original consumer purchaser must be made available for all Glacier Bay warranty claims.
This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse or normal wear and
tear. This warranty excludes all industrial, commercial & business usage, whose purchasers are hereby, extended
a ve year limited warranty from the date of purchase, with all other terms of this warranty applying except the
duration of warranty.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives you specic legal rights and you may also have other
rights that vary from state to state and province to province. Please see a store or contact 1-855-HD-GLACIER for
more details.
Pre-Installation
PLANNING INSTALLATION
Before beginning the installation of this product, ensure all parts are present. Compare parts with the Package
Contents list. If any part is missing or damaged, do not attempt to install the product. Contact customer service
for replacement parts.
TOOLS AND HARDWARE REQUIRED
Channel
lock pliers

3
Pre-Installation (continued)
PACKAGE CONTENTS
Part Description Quantity
A 1Faucet body
B 1
C Metal washer 1
Rubber washer
D 1
E Protective cap 1
Nut
H 2
IGasket 1
Bolt
FWrench 1
G Escutcheon 1
LWeight clip 1
JMounting nut 2
K 1Hose & Sprayhead
Part Description Quantity
MWeight 1
NQuick connect
assembly 1
O 1
P Battery pack 1
Sensor control box
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER for further assistance.
R 1
SSoap assembly 1
Soap pump
T 1
USoap bottle 1
Soap dispenser
mounting nut
Q"AA" Battery 4
Sensor Control Box
Soap Pump Assembly
P
A
L
M
B
C
D
E
F
J
I
H
G
K
R
S
T
U
Q
N
O

4
Installation
1 Installing the faucet assembly
□Install the faucet body (A)-including supply
hoses and sensor cable (1)-through the hole
in the sink.
CAUTION: Always turn off the water supply before
removing an existing faucet or replacing any part of a
faucet. Open the faucet handle to relieve water pressure
and ensure that the water is completely shut off.
NOTE: This step is for no escutcheon installation (optional).
If the escutcheon will be used, install the faucet assembly
as described in step 2.
2Installing the escutcheon
□Screw the bolts (H) into the escutcheon (G) and
ensure that the gasket (I) is pressed onto the
escutcheon (G) before the escutcheon (G) is
installed over the three holes in the sink.
□Secure the escutcheon (G) to the sink using the
mounting nuts (J) provided. Hand tighten only.
NOTE: If the sink is uneven, use silicone under the
gasket (I).
NOTE: This step is for escutcheon installation (optional).
If the escutcheon will not be used, install the faucet
assembly as described in step 1.
□Shut off the water supply. Remove the old
faucet.
□Clean the mounting surface.
□Proceed to step 4.
A
1
G
H
I
J

5
Installation (continued)
3 Installing the faucet assembly
□Install the faucet body (A)-including supply
hoses and sensor cable (1)-through the hole
in the escutcheon (G).
NOTE: This step is for escutcheon installation (optional).
If the escutcheon will not be used, install the faucet
assembly as described in step 1.
4 Securing the faucet assembly
□Install the rubber washer (B) and metal washer (C)
onto the threaded shank.
□Thread the mounting nut (D) onto the shank using
the wrench (F) provided to tighten rmly.
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER for further assistance.
G
A
1D
C
B
D
1
3
F
D
F
4
2

6
Installation (continued)
5 Installing the protective cap
□Screw the protective cap (E) onto the threaded
mounting shank (1).
6
Installing the pulldown hose
□Before installing the hose (K), ensure that the
protective cap (1) is on the end of the hose (K).
□Insert the small end of the pulldown hose (K) into
the spout (2) and feed through faucet body (A)
and the threaded mounting shank (3) in the
direction shown below.
7 Attaching the quick connector
to the hose
□Before installing the quick connector, remove
and discard the protective cap (1) from the
pulldown hose (K).
□Attach the quick connector (N) by screwing it
onto the threaded end of the hose (K) in a
clockwise motion. Hand tighten only.
K
1
K
1
2
N
1
E
1
E
1
2
1
A
2
3
K

HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER for further assistance.
7
Installation (continued)
NOTE: The side of the control box (O) with "in" and "out"
showing must face the front of the cabinet (away from the
back of the cabinet).
8Installing the sensor cable
□Install the data cable (1) to the control box connection (2). Ensure the arrows on the data cable (3) and the
control box connection (4) are aligned to one another to ensure proper installation. Ensure they are tightly
connected by rmly pushing together.
□Secure the connection by hand tightening the nut (5) in a clockwise direction onto the threaded sensor cable.
CAUTION: If the connections are not made properly, the
sensor feature will not work.
5
1
1
2
3
4
2

8
Installation (continued)
9Installing the batteries
□To open the battery housing, squeeze the sides while pulling the cover (1). DO NOT pull on the wire.
See g 1.
□Install the four AA batteries (Q) included by matching the positive (+) and Negative (-) ends on the battery (Q)
to the (+) and (-) markings in the battery pack (P). The negative ends of the battery (Q) should always
connect to the spring end of the battery slots in the battery pack (P). See g 2.
□Reinstall the battery pack cover (2) by pushing up and snapping into place. See gure 3.
NOTE: When the sensor ashes 10 times continuously
and slowly, the batteries have lost their charge. Replace
the batteries (Q).
NOTE: This step is for batteries installation (optional). If the
batteries will not be used, install as described in step 12.
Figure 1 Figure 2 Figure 3
P
(+)
(-)
P
1(-)
1
(+)
(-)
Q
P
Q
P
P

HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER for further assistance.
9
Installation (continued)
10Installation using the battery
pack
NOTE: This step is for battery installation (optional). If the
battery will not be used, install as described in step 12.
NOTE: After installing the battery pack, the light on the
sensor will ash and the faucet will sound when you move
your hand in the sensor area. If not, check to ensure the
batteries are installed correctly.
□Insert the battery pack cable (1) into the control box connection (2).
The light
will ash
The faucet
will sound
2
1
P

11Placing the battery pack into
the battery pack seat
□There are 2 options to secure the battery pack (P) under the counter: Tape Installation or Screw Installation.
□Screw Installation: Drill holes in the wall using a 6mm (15/64”) diamater drill bit. Install the battery pack
seat (1) using the molly anchors (3) and screws (4) provided. Place the battery pack (P) into the battery
pack seat (1).
□Tape Installation: Attach one side of the double sided tape (2) to the battery pack seat (1). Firmly attach the
battery pack seat (1) to the cabinet wall. Place the battery pack (P) into the battery pack seat (1).
NOTE: This step is for battery installation (optional). If the
batteries will not be used, skip to step 12. Before installation,
select the location for the battery pack seat (1) and verify
that the battery pack (P) will reach battery pack seat (1).
Installation (continued)
10
Screw Installation
(15/16") dia.
1
43
6mm
1
OR
Tape Installation
2
1
1
1
2
1
P3