Glacier bay FSUZAS2721A1SA1 User manual

,Monday - Friday
V1-TAP-1
SKU# & Model #,
Please refer to page 4~7

Undermount Installation
Care and Cleaning
Service Parts
Package Contents
Hardware Included 3
4
8
13
14

1-855-HD-GLACIER or visit www.HomeDepot.com/GLACIERBAY.
/under
These screws can be installed with power tools.
Hardware not shown to actual size.
Under mount clip

NOTE: Please matching your purchased product for below list.
FSUZAS2721A1SA1 Single 11
FSUZAS3621A0SA1 Double 22
NOTE: Single bowl will be with 1 grid and 1 strainer and double
bowl will be with 2 grids and 2 strainers.
Part Description Quantity
Faucet
2
2
2
2
2
2
2
2
2
Topmount/Undermount template
4
L
SKU# Model# Bowls Picture Grid Strainers

FSUZAS3021A1SA1 Single
Single
11
FSUZAS3321B1SA1 11
FSUZAS3321A0SA1 Double
Single
22
FSUZAS3621A1SA1 1
1
1
2
11
SKU# Model# Bowls Picture Grid Strainers
NOTE: Please matching your purchased product for below list.
NOTE: Single bowl will be with 1 grid, 1 strainer, 1 strainer cover
and double bowl will be with 2 grids, 2 strainers and 2 strainers covers.
Part Description Quantity
Faucet
2
2
2
2
2
2
2
2
2
2
Topmount/Undermount template
5
L
M
Strainer
cover
Strainer cover
M

NOTE: Single bowl will be with 1 grid and 1 strainer and double
bowl will be with 2 grids and 2 strainers
Part Description Quantity
2
2
2
2
2
2
2
2
2
Topmount/Undermount template
6
NOTE: Please matching your purchased product for below list.
NOTE: For the above SKUs, please skip faucet assembly for top / under mount installation.
FSUZAS2721ACC Single 11
FSUZAS3621A0ACC Double 22
SKU# Model# Bowls Picture Grid Strainers

Part Description Quantity
2
2
2
2
2
2
2
2
2
Topmount/Undermount template
7
NOTE: Please matching your purchased product for below list.
NOTE: For the above SKUs, please skip faucet assembly for top / under mount installation.
FSUZAS3021A1ACC Single
Single
11
FSUZAS3321B1ACC 11
FSUZAS3321A0ACC Double
Single
22
FSUZAS3621A1ACC 1
1
1
2
11
SKU# Model# Bowls Picture Grid Strainers Strainer
cover
M
2
Strainer cover
M
NOTE: Single bowl will be with 1 grid, 1 strainer, 1 strainer cover and
double bowl will be with 2 grids, 2 strainers and 2 strainers covers.

Undermount Installation
HOMEDEPOT.COM/GLACIERBAY
8
Preparing the countertop
Preparing the cabinet
Position the template (provided with the sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
Trace the template and remove. Dry fit the sink to verify measurements.
Following the countertop manufacturer's instructions, carefully cut the
countertop on the traced line.
Construct a support frame to fit inside the cabinet opening. Provide
appropriate clearance for faucet, water supply lines, drain assembly,
garbage disposal and structural parts of the cabinet.
Apply painter's tape to the cabinets for marking and cutting purposes. This
will protect the cabinet from damage while cutting.
Outline the cutout on the front of the cabinet according to the actual sink.
Using a sharp saw blade, carefully cut the cabinet on the traced line.
NOTICE: lt is strongly suggested that you contact a professional
countertop fabricator when installing the sink as an undermount.
NOTICE: The cabinet must be installed, secured, plumb, and level
beffore installing the sink.
NOTICE: lt is recomncended to provide the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than
the apron front.
NOTICE: Double check the measurement of the cabinet cutout and make
any necessary adjustments by either adding filler strips or sanding the
opening.
NOTICE: A custom sink base cabinet and support framing is required for

Installing the strainer assembly
Installing the sink
HOMEDEPOT.COM/GLACIERBAY
Undermount Installation (continued)
9
4
Place the sink (A) into the installation hole to verify the fit, Adjust the cutout if necessary.
Install the strainer assembly as these steps describe. It is easier to install the strainer assembly
to the sink before the sink is installed to the cabinet.
1) Apply a small amount of plumber's putty (not included) in the notch around the drain hole of
the Sink (A). Place the strainer ring (E) on top of the drain hole in the sink (A).
2) Insert the screener (C) into the bowl (D) and place thiS assembly into the drain hole in the
Sink (A).
3) From underneath the sink (A), place the rubber washer (F), paper washer (G), locknut (H),
plastic joint (I), and connecting nut (J) over the drain hole in the Sink (A).
4) Tighten the locknut (H) and connecting nut (J) to hold the strainer assembly securely in
place.
Clean the sink apron and top rim of all debris. Ensure that the surface on underside of
countertop cutout opening is smooth and free of debris.
Lower the sink onto the supports and verify the sink is supported by the frame.
Push the sink in to ensure the apron is flush to the front of the cabinet.
Verify the sink is level. Make any adjustments and shim as needed.
NOTICE: The front sink apron must be secured to the front of the cabinet by
attaching fasteners through the cabinet front and into the support framing. Failure
of this step can lead to product damage.
NOTICE: The manufacturer is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink
for damage prior to beginning installation.
NOTICE: Metal edges may be sharp - use caution when handling.

HOMEDEPOT.COM/GLACIERBAY
Undermount Installation (continued)
10
6 7Securing the faucet assemblyInstalling the faucet assembly
L
21
Sink
Push
up
21
1 1
Push
up 21
2
3
3
Sink
21
Sink
Continue to push up
and turn clockwise
to tighten
Installing the countertop
5
Clean the bottom of the countertop and the top flange (or lip) of the sink
with denatured alcohol.
Apply a narrow bead of silicone adhesive seaiant around the side and back
of the sink.
Carefully position and secure the sink to the countertop following the
manufacturer's instructions.
Apply a thin bead of silicone sealant where the sink meets the countertop
and cabinet.
Immediately remove excess sealant.
Shut off the water supply.
Drill a hole with diameter of 1.38 in. in the counter top, and Insert the
faucet body (L) through the hole in the counter top.
From underneath the sink, secure the faucet assembly to the sink with
the FastmountTM system (21). Push the FastmountT M system (21 )
up over the threads until it stops against the bottom of the sink, then
hand turn (clockwise) to tighten.
CAUTION: Always shut off the water supply before removing an existing
faucet or replacing any part of a faucet. Open the faucet handle to relieve
water pressure and ensure that the water is completely shut off.