Glacier bay VDR2522A1 User manual

,Monday - Friday
SKU#
Model# VDR2522A1 /
VDR3322A1 /
VDR3322A0
V1-TD-2

Topmount Installation
Undermount Installation
Care and Cleaning
Service Parts
Package Contents
Hardware Included 3
4
8
12
15
16

1-855-HD-GLACIER or visit www.HomeDepot.com/GLACIERBAY.
/under
(NOT INCIUDED)
HARDWARE REQUIRED (NOT INCIUDED) HARDWARE REQUIRED (NOT INCIUDED)
HARDWARE REQUIRED (NOT INCIUDED)
HARDWARE REQUIRED
Undermount CIips (10 recommended )
These screws can be installed with power tools.
Hardware not shown to actual size.

SKU# Model# Bowls Picture
VDR2522A1
VDR3322A1
VDR3322A0
Single
Single
Double
NOTE: The manual only displays the assembly for double bowl
sink, but the assembly instruction is including but not limited to
below SKU & configuration
4
NOTE: Please matching your purchased product for below pages

Q
R
S
Part Description Quantity
N
O
Mounting nut
Soap assembly
Soap pump
L
N
M
O
P
T
FastMount™
Faucet assembly
Weight
Quick connector
Weight clip
Q
R
S
T
Topmount/Undermount template
5

Q
R
S
Part Description Quantity
N
O
Mounting nut
Soap assembly
Soap pump
L
N
M
O
P
T
FastMount™
Faucet assembly
Weight
Quick connector
Weight clip
Q
R
S
T
Topmount/Undermount template
P
1
1
1
6

Q
R
S
Part Description Quantity
N
O
Mounting nut
Soap assembly
Soap pump
L
N
M
O
P
T
FastMount™
Faucet assembly
Weight
Quick connector
Weight clip
Q
R
S
T
2
2
2
2
2
2
2
2
2
Topmount/Undermount template
P
7

.
.
Installing the strainer assembly
Topmount Installation
Installation Types
8

4
Shut off the water supply.
Insert the faucet body (L) through the hole in the
sink.
5Securing the faucet assembly
From underneath the sink, secure the faucet
assembly to the sink with the FastMount™
system (M). Push the FastMount™ system (M)
up over the threads until it stops against the
bottom of the sink, then hand turn (clockwise)
to tighten (Fig 1).
Installing the faucet assembly
Sink
Sink
Push
up
Screw
Fig 1
L
CAUTION: Always shut off the water supply before
removing an existing faucet or replacing any part of a
faucet. Open the faucet handle to relieve water pressure
and ensure that the water is completely shut off.
7Installing the weight
Insert the weight (O) onto the clip (P) by sliding
it down onto the clip (P).
Install the weight clip (P) at the point of the
hose marking “weight here”.
6Attaching the quick connector
to the receiving block
Push the quick connector (N) firmly upward and
attach it to the receiving block (1). Pull down
moderately to ensure the connection has been
made.
1
Weight
here
Weight
here
Topmount Installation (continued)
9

8Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
into the soap assembly (O).
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly(O) to the sink with
9
10
Making the water supply connections
Thread the nut (1) on the supply line onto the outlet of the
water supply valve (2) and tighten with a wrench. Do not
overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
1
2
Q
O
S
T
Topmount Installation (continued)
These screws can be installed with power tools.
10