Glasdon Electra Bin Specifications

ELECTRA®BIN
Operator Instruction Leaet
To Secure a Sack in Position (Sack Retention Model).
To Open.
IMPORTANT NOTE: ENSURE THAT ALL RELEVANT PERSONNEL READ THESE INSTRUCTIONS PRIOR TO USE
Using the triangular-shaped
key provided, turn the key
anti-clockwise to unlock the
door.
1.
5.
Pull the sack retention
system forwards.
Pull the rear sack band
upwards.
Drop the sack down
through the sack bands.
1
The door is tted with a
magnetic strip to help retain
the door when unlocked.
2.
Slide the liner out of the
bin by pulling on the liner
handle.
3.
To Empty and Replace Solid Liner.
4.
Lift the liner inside the bin and
rest it on the internal shelf using
the liner handle.
6. 7.
The magnet will take a small
amount of force to override.
The magnet is designed to
keep the door shut whilst
the liner / refuse sack is
emptied.

ELECTRA®BIN
Operator Instruction Leaet
8.
Press the edges of the bag
over the edge of the sack
bands. Press the rear sack band
downwards to add tension and
secure the sack in place.
Push the sack retention
system back inside the bin.
Close the door and lock the
bin using the triangular key,
turning the key clockwise.
9. 10.
2
To Empty and Replace the Ashtray Liner.
Open the bin
(as shown in
diagrams 1-2) and
remove main bin
liner or pull the
sack retention
forwards. Lift
Ashtray from
brackets and
remove from the
bin.
Empty Ashtray
liner and
replace by
hooking back
onto the
brackets.
To Assemble the Freestanding Base (60L Model)
Place the Free Standing
Base on the ground, with the
pre-xed screws protruding
upwards.
Place the Electra Litter Bin on
the Free Standing Base and
align holes in the base of the
bin with the four screws.
Secure in position using
the M10 washer [ITEM
3] and M10 Nut [ITEM 4]
and tighten using an M10
Spanner.
Ensure the base is secured
in position and place in an
appropriate location.
ITEM 1 - Free Standing Base Kit x1
ITEM 2 - M10 Screw x4
ITEM 3 - M10 Washer x4
ITEM 4 - M10 Nut x4
TOOLS REQUIRED
10mm Spanner / Socket x 1

ELECTRA®BIN
Operator Instruction Leaet
12.
Place the bin in the desired location.
Inspect the condition of the concrete you
wish to install in to. If installing into paving
slabs- ensure xings are not positioned
within 110mm of the edge of a slab (as
doing so may cause the slab to break).
13.
Move the bin to one side to
allow the holes to be drilled.
Ensure the holes are clearly
visible.
Mark the positions of the
four ground xing holes in
the base of the bin onto the
concrete base below using
a marker pen.
11.
KIT CONTENTS:
ITEM 1 - Anchor Rawl Plug x 4
ITEM 2 - Screw (M10 x 60mm) x 4
ITEM 3 - M10 x 50mm Washer x 4
14.
Using a powerful drill - drill the four
16mm diameter xing holes to a
minimum depth of 80mm. Afterwards,
take care to ensure the concrete dust
is removed from the holes using an air
blower or sweeping brush.
15.
Take the four Anchor Rawl
Plugs (ITEM 1) and using a
hammer gently tap them
into the four ground xing
holes.
16.
Place the bin back into
position. Take care to align
the ground xing holes.
3
17.
Take the M10 Screws (ITEM 2) and
Washers (ITEM 3) and t them
through the base of the bin and
into the ground anchor sleeves t-
ted into the concrete.
18.
Tighten the M10 Screws using a
Socket Wrench tted with a17mm
Socket or 17mm Spanner -
(maximum recommended torque
setting is 40Nm).
TOOLS REQUIRED:
Marker Pen
Drill with Ø16mm Masonry Drill Bit
Hammer
17mm Socket Set or 17mm Spanner
Lubricant or Grease
To Install the Litter Bin
(Ground Fixing).

ELECTRA®BIN
Operator Instruction Leaet
To Install the Litter Bin (Concrete-In).
Lay the bin on its back
(onto a soft surface which
will not cause damage to
the product). Attach the
four concrete xings (ITEM
4) through the ground xing
holes as shown. Use a 17mm
Spanner or Socket Wrench to
secure.
Prepare a hole.
• Electra 60L- 500mm long,
350mm wide, 400 deep.
• Electra 85L- 500mm long,
500mm wide, 400mm deep.
Fill the base with an 80mm deep
layer of ne gravel. Place support
blocks under the positions where
the concrete xings will rest at the
base of the hole.
19. 20. 21.
Fit the bin into the hole to test
the depth and level of the
hole. Adjust the support blocks
and depth of the gravel until
the base supports the bin so
that the base sits level with
the ground surface and is
vertically level.
4
KIT CONTENTS: TOOLS REQUIRED:
ITEM 4 - Adjustable Depth Concrete-in Fixing x 4 Equipment to excavate hole.
ITEM 5 - M10 x 50mm Washer (Zinc Plated) x 4 Concrete Mix.
ITEM 6 - M10 Wing Nut x 8 Spirit Level.
ITEM 7 - Screw (M10 x 100mm) x 4 17mm Socket Set or 17mm Spanner.
ITEM 8 - M10 x 50mm Washer (Stainless) x 4 Lubricant or Grease.
22. 23. 24.
Pour in the concrete mix to
the desired level.
Use a spirit level to check
the alignment in all
orientations.
Glasdon U.K. Limited
Preston New Road
BLACKPOOL
Lancashire FY4 4UL
Tel: [phone]
Fax: [phone]
email: [email protected]
web: www.glasdon.com
AND ELECTRA®BIN ARE TRADEMARKS OF GLASDON GROUP
OR ITS SUBSIDIARIES IN THE U.K. AND OTHER COUNTRIES
•A planned maintenance schedule of regular inspection is recommended, replacing
components as necessary.
• Replacement components are available direct from GLASDON UK LIMITED.
• GLASDON UK LIMITED cannot be held responsible for claims arising from incorrect installation,
unauthorised modifications or misuse of the product.
Issue 1 August 2015 Stock No. C000/0480 DWG No. 07B-354-31
© Copyright August 2015 Glasdon UK Ltd reserve the right to alter specifications without prior notice.
400mm
500mm
Wipe away any excess
concrete around the base.
4
Issue 2 February 2016
February 2016