Glen 6072 User manual

Cooker Hood 6072
Auto Clean 90 cm 1400
U S E R ' S G U I D E
TH
4 Generation
Auto Clean System

Note : It is recommended to use a 4" dia pipe for chimneys with airflow 1000m³/h and
a 6" dia for chimneys with 1250m³/h airflow.
Installing the duct covers
Fix the bracket with 2 plugs and screws at the required height for the duct cover. Screw
the short duct with 2 screws on the bracket. Insert the 2 nuts in the holes on the lower
part of the long duct. Put the long pipe over the short one by pulling apart the laterals of
the duct. Insert the nuts supplied, and working from the inside of the chimney, using
the two screws fix the long duct. In a few models the long duct can be fixed by using
two screws which must be inserted into the holes at the bottom of the duct. (In some
models (6054/6055) you will find only one long duct cover).
Electric connection
Make sure that the supply voltage ratings correspond with the specifications provided
in the User's Guide
USING YOUR CHIMNEY
Switch on the chimney 5 minutes before you start
cooking. Before using the chimney please ensure that all
plastic films on the filter and stainless steel body are
removed.
There are three speed settings, choose the speed as per your requirement..
Light
LED lamps are provided in the chimney to enable proper lighting up of the cooking
area. The light works independently of whether the fan is switched on or off, as it is
provided with a separate on/off switch.
MAINTENANCE
When performing maintenance operations, disconnect the plug from the socket.
Auto clean chimney
Easy cleaning | Longer life | Better performance
Using the auto clean
Push the auto clean button to run the cleaning program. The element starts heating
o
from the normal temperature to a max of 90 C temperature. It stays at this temperature
for atleast 3 minutes. During this time, the oil in the blower melts and collects in the oil
cup. Once completed the elements cool down and finish the program in about 2 mins.
The filters can be removed easily by unlocking. Dip the filters for 10-15 minutes into a
boiling hot soap solution and then wash in running water. Dry and reinstall the filters.
The chimney surface should be cleaned with a damp cloth. No abrasive chemicals
should be used.
Please note that your Chimney is made from Magnetic Stainless Steel and needs to be
cleaned regularly and kept dry otherwise it may react to the moisture and dust and
develop a rust kind of formation.”
SETTING UP YOUR CHIMNEY
The chimney must be mounted over the center of the
cooking area. The minimum distance between the
cooktop and the bottom of the chimney must be 750 mm.
Please ensure that the wall on which the chimney is being
installed is level properly if not either get it leveled or
install the chimney on a leveled ½ ” plywood
Attach the spigot to the hood using the four screws. In a
few models the spigot may already be mounted.
Fastening the chimney to the wall
Mark the position of the holes on the wall. Before drilling
make sure that no wiring and tubes will be damaged. Drill
two fastening holes, drive in the wall plugs and screw in
the screws until their heads are about 6 mm from the wall.
Place the chimney to the wall in order to check that it
seats properly. Then mark the positions of the two holes.
Take it off from the wall now, drill the holes and fit the
plugs. Place the hood once again to the wall, and
introduce the screws from the inside of the appliance.
The chimney can be used either in re-circulation or the
exhaust mode. It is however recommended that wherever
possible it should be used in exhaust mode for best
results.
Exhaust mode
The chimney must be connected by the spigot (supplied as part of the hood) to a duct to
vent all the exhausted air outside the kitchen. Over horizontal areas, if any, the duct
must be slanted about 10% downwards. The maximum recommended length of
ducting is 10feet with a maximum of two bends. The suction power of the chimney
considerably decreases in case the length of the number of bends increase further.
750 mm
IDENTIFYING YOUR CHIMNEY
ON/OFF LIGHT AUTO CLEAN
The body of your Glen chimney is made up of high quality Stainless Steel. The Chimney body
is warranted against rust formation for life time.
SS Hood
Touch
Panel
Grease
Filter

SPECIFICATIONS
Voltage : 230 V AC 50Hz
Airflow m³/h : 1400
Power Motor : 265 W
LED Light 2 x 1.5 W
Size : 90 cms
GUARANTEE
Glen Appliances Pvt. Ltd. guarantees to get the Chimney Hood or any part thereof repaired
free of charge for a period of one year from the date of purchase, should any defect develop
due to faulty or defective workmanship or material. However, the plastic breakable parts,
lamps, push buttons, filter locks, and items subject to normal wear and tear due to
operation are not covered under guarantee. The stainless steel body of the chimney is
warranted against rust formation for life time. The warranty excludes baffle filters, GI
clamps, GI back panel & GI chimney tube support bracket. The warranty will not be
applicable if food/dust particles are left on the body for very long time.
Terms to Guarantee
* The Bill/Cash Memo should be presented.
* No repair work should be carried out by any unauthorised person.
* Chimney Hood should be used as per the directions given in the user’s guide.
* Any defects caused by improper or reckless use are not covered
under guarantee.
* The Serial no. has not been tampered with.
* No modification/alteration of any nature is made in the Chimney Hood.
The company accepts no responsibility for any consequential losses arising out of
misuse or negligence on the part of the user.
DEALER'S STAMP & SIGNATURE
Packing List Main unit, spigot, plastic wall plugs, screws
Housing : Metal Housing
Speed Control : 3 speed
Net Weight : 22 Kgs
Gross Weight : Kgs28.
Dimensions (mm) (w x d x h)
Chimney : 895 x 400 x 520
Carton : 965 x 565 x 49.5
CHIMNEY
SERIAL NO. BILL NO. DATE OF PURCHASE
NAME OF OWNER
ADDRESS
Imported & Marketed by/In case of customer
complaints Contact Manager - Customer Support
Glen Appliances Pvt. Ltd.,
I-34, DLF Ind. Area, Phase-I, Faridabad, India.
Helpline : 9266655555
E-mail : [email protected]
Website : www.glenindia.com