Global American Inc. 3308180 User manual

2008.04
User’s Manual
Version 1.0
Half-size PCI-SBC 3308180

Copyrights
This manual is copyrighted and all rights are reserved. It does not allow any non
authorization in copied, photocopied, translated or reproduced to any electronic or
machine readable form in whole or in part without prior written consent from the
manufacturer.
In general, the manufacturer will not be liable for any direct, indirect, special, incidental
or consequential damages arising from the use of inability to use the product or
documentation, even if advised of the possibility of such damages. The manufacturer
keeps the rights in the subject to change the contents of this manual without prior
notices in order to improve the function design, performance, quality and reliability. The
author assumes no responsibility for any errors or omissions, which may appear in this
manual, nor does it make a commitment to update the information contained herein.
Trademarks
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
All other trademarks, products and or product's name mentioned herein are mentioned
for identification purposes only, and may be trademarks and/or registered trademarks of
their respective companies or owners.

Index
- i -
Table of Contents
Chapter 1 - Introduction............................................ 1
1.2 About this User’s Manual...........................................2
1.3 Warning .......................................................................2
1.4 Replacing the lithium battery ....................................3
1.5 Technical Support.......................................................3
1.7 Packing List.................................................................5
1.8 Ordering Information..................................................5
1.9 Specication ...............................................................6
1.10 Board Dimensions....................................................7
1.11 Installing the CPU .....................................................9
1.12 Installing the Memory.............................................10
Chapter 2 - Installation............................................ 11
2.1 Block Diagrams.........................................................12
2.2 Jumpers and Connectors ........................................13
Jumpers............................................................................14
JBAT1: Clear CMOS Setup ..........................................................14
JVLCD1: LCD Panel Voltage Select............................................ 14
JRS1: COM2 RS-232/422/485 Select........................................... 14
Connectors.......................................................................15
LPT1: Parallel Port Connector ....................................................15
FDD1: FDD 34-pin connector ......................................................16
IDE1: Primary 40-pin IDE Connector..........................................17
JP2I1: Options for PCI to ISA signal ..........................................18
USB1/ USB2/ USB3: USB Connector..........................................18
IDE2: Secondary IDE 44-pin Connector.....................................19
INV1: LVD Inverter Connector..................................................... 20
AUDIO1: AUDIO Interface............................................................20
LVDS1: LVDS LCD Connector.....................................................21
LCD1: TTL LCD Connector..........................................................22
JSMB1: External SMBus Connector...........................................22
EKB1: External keyboard/Mouse................................................ 23

Index
KBM1: PS/2 Keboard & Mouse ...................................................23
VGA1: CRT Connector................................................................. 23
LAN1: 10/1000 RJ-45.................................................................... 24
COM1: RS232 Connector.............................................................24
JCOM2: RS-422/485 Output Connector......................................24
IR1: Infrared Connector...............................................................24
COM2: RS232 Connector.............................................................25
JFRT1: Switches and Indicators................................................. 25
CPUF1: CPU Fan Power Connector ...........................................25
PWR1: Power Supply Connector................................................ 26
EATX1: ATX Feature Connector.................................................. 26
Chapter 3- Appendix .............................................. 27
3.1 I/O Port Address Map ...............................................28
3.2 Interrupt Request Lines (IRQ)..................................29
- ii -

Introduction
- 2 -
1.2 About this User’s Manual
This User’s Manual is intended for experienced users and integrators with
hardware knowledge of personal computers. If you are not sure about any
description in this User’s Manual, please consult your vendor before further
handling.
1.3 Warning
Single Board Computers and their components contain very delicate
Integrated Circuits (IC). To protect the Single Board Computer and its
components against damage from static electricity, you should always follow
the following precautions when handling it :
1. Disconnect your Single Board Computer from the power source when you
want to work on the inside.
2. Hold the board by the edges and try not to touch the IC chips, leads or
circuitry.
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that came
with the Single Board Computer, whenever components are separated
from the system.

Introduction
- 3 -
1.4 Replacing the lithium battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery
type recommended by the manufacturer.
Do not throw lithium batteries into the trashcan. It must be disposed of in
accordance with local regulations concerning special waste.
1.5 Technical Support
Please do not hesitate to call or e-mail Technical Support if you have any
questions:
Phone [phone]
Click for Technical Support

Introduction
- 4 -
This page intentionally left blank.

Introduction
- 5 -
1.7 Packing List
If any of the above items is damaged or missing, contact your vendor
immediately.
1 x 3308180 Half-size PCI SBC
or
1 x CPU Heat Sink or Cooler
1 x Driver CD
1 x Quick Installation Guide
1.8 Ordering Information
3308180B Half-size PCI Intel® Pentium® / Celeron® M socket 478
SBC with CRT/LCD, Audio & LAN
3308180A Half-size PCI with embedded Intel® µFC-BGA
Celeron® M 600MHz SBC with CRT/LCD, Audio & LAN
BackplanesClick for - PCI Backplanes for expansion

Introduction
- 6 -
1.9 Specification
Form Factor Half-size PCI SBC
Processor Intel® μFC-PGA Pentium® M up to 1.8GHz (FSB
400MHz)
Chipset Intel® 852GM + Intel® ICH4
System Memory 1 x 184-pin DIMM socket up to 1GB DDR
200/266/333 Mz SDRAM
VGA Controller
Intel® 852GM Extreme Graphics 2 (2D/3D) up
to 64MB with CRT/LVDS/TTL (Dual independent
display)
Ethernet 1 x Intel® 82562ET PCI 10/100 Base-T Ethernet
I/O Chips Winbond W83627HG
BIOS Phoenix-Award BIOS
Audio AC’97 Codec, onboard supports MIC-in/Line-in/
Line-out
IDE Interface 1 x Ultra DMA 100/66/33, supports 2 IDE devices
1 x Ultra DMA 33, supports 2 IDE devices
Serial Port 2 x COM port (COM1: RS-232, COM2: RS-
232/422/485 Selectable
Parallel Port 1 x SPP/EPP/ECP mode
FDD 1 x Floppy connector
KBMS Standard PS/2 Keyboard and Mouse
Universal Serial Bus 6 x USB 2.0
Expansion Interface 1 x CF II
Hardware Monitor
Chip Integrated in W83627HG
RTC Real Time Clock
Operating Temp. 0ºC ~ 60ºC (32ºF ~ 140ºF)
Watchdog Timer 255-level Reset
Dimension (L x W) 185 x 122mm (7.3” x 4.8”)

Introduction
- 7 -
1.10 Board Dimensions

Introduction
- 8 -

Introduction
- 9 -
1.11 Installing the CPU
The processor socket comes with a screw to secure the CPU. As showing in
the picture as bellow, loose the screw rst before inserting the CPU.
Place the CPU into the socket by making sure the notch on the corner of the
CPU corresponding with the notch on the inside of the socket. Once the CPU
has slide into the socket, lock the screw.
Make sure that heat sink of the CPU top surface is in complete contact to
avoid the CPU overheating problem.
If not, it would cause your system or CPU to be hanged, unstable, damaged.

Introduction
- 10 -
1.12 Installing the Memory
To install the Memory module, locate the Memory DIMM slot on the board
and perform as below:
1. Hold the Memory module so that the key of the Memory module align
with those on the Memory DIMM slot.
2. Gently push the Memory module in an upright position and a right way
until the clips of the DIMM slot close to lock the Memory module in place,
when the Memory module touches the bottom of the DIMM slot.
3. To remove the Memory module, just pressing the clips of DIMM slot with
both hands.
Lock Lock

Installation
- 11 -
2Chapter 2
Installation
Chapter 2 - Installation

Installation
- 12 -
2.1 Block Diagrams
Analog
R.G.B.
VGA
Intel®
82852GM
Pentium M socket 479
for Intel® CPU
FSB
400MHz
Hub Link
USB I/F
IDE ATA I/F Intel®
ICH4
SM Bus
Audio
Memory Bus
Super IO
COM1
COM2
LPT1
FDD
IrDA
KB
MS
Codec
AC’97
SMBus
LPC I/F
6 x USB
2 x IDE
1 x CF
1 x 184pin DDR
DIMM socket
PCI Bus
PICMG PCI GF
LVDS
1 x RJ-45
10/100 base-T
TTL LCD
LAN
Controller

Installation
- 13 -
2.2 Jumpers and Connectors
PWR1
EATX1
COM2
Socket 479
JRS2
FDD1
IDE1
IDE2
JP2I1
USB1
USB2
USB3
LVLCD1
JSMB1
EKB1 KBM1
LVDS1
LCD1
JBAT1
BAT1
INV1
AUDIO1
CPUF1
IR1
JCOM2
LAN1
JFRT1
COM1
VGA1
25
6
5
2
2120
19
24
15 23
16 17 18
22
26
10
9
3
7
8
11
12
13
14
4
LPT1
1

Installation
- 14 -
Jumpers
JBAT1: Clear CMOS Setup (9)
Pin Mode
1-2 Keep CMOS (Default)
2-3 Clear CMOS
JVLCD1: LCD Panel Voltage Select (10)
The voltage of LCD panel could be selected by JVLCD1 in +5V or +3.3V.
Pin Voltage
1-2 +5V
2-3 +3.3V (Default)
1 3
JRS1: COM2 RS-232/422/485 Select (26)
It can be congured COM2 to operate in RS-232, RS-422 or RS-485 mode
Pin Mode
1-2 (Short) RS-232 (Default)
3-4 (Short) RS-422
5-6 (Short) RS-485
65
2
1

Installation
- 15 -
LPT1: Parallel Port Connector (1)
Pin Description Pin Description
1 STB 14 #AFD
2 PD0 15 #ERR
3PD1 16 #INIT
4 PD2 17 #SLIN
5 PD3 18 GND
6 PD4 19 GND
7PD5 20 GND
8 PD6 21 GND
9 PD7 22 GND
10 #ACK 23 GND
11 BUSY 24 GND
12 PE 25 GND
13 SLCT 26 N/C
Connectors
1
13
14
26

Installation
- 16 -
FDD1: FDD 34-pin Connector (2)
12
33 34
Pin Description Pin Description
1 GND 2 #RWC
3 GND 4 N/A
5 GND 6 #DS1
7 GND 8 #INDEX
9 GND 10 #MOA
11 GND 12 #DSB
13 GND 14 #DSA
15 G ND 16 #MOB
17 GND 18 #DIR
19 GND 20 #STEP
21 GND 22 #WD
23 GND 24 #WE
25 GND 26 #TRAK
27 GND 28 #WP
29 GND 30 #RDATA
31 GND 32 #HEAD
33 GND 34 #DSKCHG

Installation
- 17 -
IDE1: Primary 40-pin IDE Connector (3)
Pin Description Pin Description
1 IDE RESET 2 GND
3 DATA7 4 DATA8
5 DATA6 6 DATA9
7DATA5 8 DATA10
9 DATA4 10 DATA11
11 DATA3 12 DATA12
13 DATA2 14 DATA13
15 DATA1 16 DATA14
17 DATA0 18 DATA15
19 GND 20 N/C
21 REQ 22 GND
23 IO WRITE 24 GND
25 IO READ 26 GND
27 IO READY 28 IDESEL
29 DACK 30 GND
31 IRQ14 32 N/C
33 ADDR1 34 ATA66 DETECT
35 ADDR0 36 ADDR2
37 #CS0 38 #CS1 (#HD SELET1)
39 IDEACTP 40 GND